- Vehicles & accessories
- Motor vehicle electronics
- Car media receivers
- Kenwood
- KMD-PS970R
- Instruction manual
advertisement
![Auto TP Seek Function. Kenwood KMD-PS970R, kmdps 970 r dab | Manualzz Auto TP Seek Function. Kenwood KMD-PS970R, kmdps 970 r dab | Manualzz](http://s3.manualzz.com/store/data/059496060_1-9a041cc84c84b6705cbdbe1cb90d85e9-360x466.png)
switches reception to the FM band. However, the MW/LW band is not returned to when the TI button is pressed again.
Switching to a Different Traffic Information Station:
Use the
4
/
¢ buttons to make an auto seek of the TI stations in a certain band.
NOTE
• When you are listening to a tape or disc, you cannot change to another TI station.
• When the auto TP seek function is turned on and reception starts to weaken, the tuner automatically seeks traffic information stations with better reception.
• If you are tuned to a station that is not a traffic information station itself but which provides EON services, you can still have traffic information received.
• Holding the TI button down for one second or more when the TI function is on in the disc control mode results in a change to the frequency display of the traffic information station for five seconds.
Auto TP Seek Function
When the TI function is on and poor reception conditions are experienced when listening to a traffic information station, another traffic information station with better reception will be searched for automatically. This function is on, when unit is first powered on.
Turning Auto TP Seek Function On/Off:
1
Hold down the MENU button for one second or more.
"MENU" is displayed and the menu mode is turned on.
2
Press the
¢ button repeatedly until the Auto TP Seek function appears in the display.
Press the
4 button to search in the other direction.
The function setting is indicated by "ATPS ON" or "ATPS OFF" in the display, indicating that the function is on or off, respectively.
3
4
Switching settings
Press either the AM button or FM button.
The display and setting will change.
If the traffic information station you are tuned to experiences poor reception, this function automatically seeks another TP station.
Press the MENU button to end the menu mode.
Presetting Volume for Traffic Information/News
Preset the volume level to be used for traffic information and news broadcasts.
1
2
3
Tune into the station for which you want to set the volume.
Adjust the volume to the desired level.
Hold down the TI VOL ADJ button for two seconds or more.
The volume level blinks once in the display to indicate that the data has been stored.
Future traffic information/news broadcasts are heard at the preset level.
NOTE
• The volume cannot be lowered by this function during tuner reception. The volume is only set when it is louder than the listening volume of the tuner.
• You can arrange only to listen to traffic information or news bulletins with at preset volume with the volume set at minimum.
— 15 —
advertisement
Related manuals
advertisement
Table of contents
- 3 Safety Precautions
- 6 Power
- 7 Switching Modes
- 7 Volume
- 7 Attenuator
- 7 Loudness
- 8 Menu System
- 9 Selecting Tuning Mode
- 10 Tuning
- 10 Local Seek Function
- 10 Monaural Reception
- 10 Station Preset Memory
- 11 Auto Memory Entry
- 12 Preset station seek with Programme service name
- 12 Clock display
- 12 Kenwood intelligent Twin IF (K2I)
- 13 RDS (Radio Data System)
- 13 EON (Enhanced Other Network)
- 13 Alarm
- 14 AF (Alternative Frequency) Function
- 14 Restricting RDS Region (Region Restrict Function)
- 14 Traffic Information Function
- 15 Auto TP Seek Function
- 15 Presetting Volume for Traffic Information/News
- 16 Text Scroll
- 16 Radio Text
- 16 Programme Type (PTY) Function
- 18 News Bulletin Function with PTY News Timeout Setting
- 20 Playing MDs
- 20 Playing Other Disc mode
- 20 Switching Display for Discs
- 21 Clock display
- 21 Fast Forwarding and Reversing Disc Play
- 21 Track Search
- 22 Disc Search
- 22 Track / Disc Repeat
- 22 Track Scan
- 22 Disc Scan
- 23 Text / Title Scroll
- 23 Random Play
- 24 Presetting Disc Names
- 25 Disc Name Preset Play (DNPP)
- 25 Magazine Random Play
- 26 Audio Control Setting
- 27 Switching Graphic Display
- 28 Switching Spectrum Analyzer Display
- 28 Dimmer
- 28 Automatic Dimmer Function
- 28 TEL Mute
- 29 Selectable Illumination
- 29 Touch Sensor Tone
- 29 Non-fading preout
- 30 Adjusting Time
- 30 Mask Key
- 31 Dual Zone System
- 32 Faceplate Angle Adjustment
- 32 Manual Open Switch Setting
- 32 Black Mask
- 33 Dimmer level adjustment
- 33 External Amp Control
- 33 Navigation Mute Function
- 34 Basic Operations of steering remote control
- 36 Accessories
- 36 Installation Procedure
- 37 Connecting Cables to Terminals
- 38 Installation
- 39 Removing the Unit
- 40 Attaching Steering Remote Control
- 41 Troubleshooting guide
- 44 Specifications