advertisement
Section 3: Operation
Intelligent Lens System (ILS)
The ILS button launches a control screen used to adjust the Focus, Horizontal (X) and Vertical (Y) Offset, and
manually override the intelligent lens system settings.
When the channels are changed, the ILS automatically moves the lens to adjust the focus, Horizontal (X) and
Vertical (Y) offset, and zoom based on the pre-defined settings. All manual override settings are lost. This feature should only be used to make quick changes. Proper adjustments should be made in the Channel: Lens menu when time permits.
When ILS is enabled ( Automatic ILS is checked) and the channel has been specified, it begins adjusting each motor. The proper lens type must be selected from the Advanced: Lens menu beforehand. The position of each motor is then saved onto the system in the specific channel file. This is not a global feature - instead it is controlled on a per channel basis. When this feature is enabled, the ILS for the currently selected channel is turned ON. NOTES: 1) Using the knobs on the lens mount to adjust these positions does not save the settings to the channel. They are designed for temporary use and will therefore be lost once the channel changes. 2)
Only Advanced users can modify channel settings. 3) Keep clear of rotating parts. Remotely operated motors may start to spin without warning. 4) In case of emergency, unplug the line cord to immediately halt movement of the lens mount.
To Enable ILS Per Channel
1. From the Main menu, select one of the available channels.
2. Enable Test Patterns checkbox to select a test pattern.
3. Select the ILS button from the Main menu to launch the ILS screen (
).
4. Select Automatic ILS to automatically apply the per channel settings.
To Edit Active Channel ILS Settings
1. Ensure Automatic ILS is checked.
Figure 3-9 Intelligent Lens System
2. Adjust the focus, Horizontal (X) and Vertical (Y) offset or zoom one step at a time by clicking the applicable button or hold the button down for continuous movement. If you hold a button down, a Pending message will display until you release the button. NOTE :
This over-writes the intelligent lens system settings.
To Temporarily Alter the Active Channel ILS Settings
1. De-select the Automatic ILS checkbox.
2. Adjust the focus, Horizontal (X) and Vertical (Y) offset, and zoom. NOTE : This does not over-write the system settings for the ILS.
3. To revert back to the ILS settings, check Automatic ILS .
Start Features or Presentations
To start a different feature or presentation, click its corresponding display Channel button. NOTE: By clicking a channel button, test patterns are automatically turned OFF to present show content.
3-16 CP2000-ZX User Manual
020-100006-05 Rev. 1 (05-2009)
advertisement
Related manuals
advertisement
Table of contents
- 44 Guidelines for Using the CDP
- 45 Icons
- 45 Pull-Down Lists
- 46 Using Slide Bar Controls
- 46 Editing Text or Numerical Values
- 46 Channel Menu
- 47 Lamp Menu
- 47 Lens Control Menu
- 48 Configuration Menu
- 49 Status Menu and Alarm Conditions
- 49 Test Patterns Menu
- 53 Power ON or OFF
- 53 Turn the Lamp ON or OFF
- 53 Open or Close the Douser (Shutter)
- 53 Display a Test Pattern
- 53 Move the Auxiliary Lens
- 54 Intelligent Lens System (ILS)
- 54 To Enable ILS Per Channel
- 54 To Edit Active Channel ILS Settings
- 54 To Temporarily Alter the Active Channel ILS Settings
- 54 Start Features or Presentations
- 55 Status: System Menu
- 58 Status: Test Menu
- 59 Status: Status Summary Menu
- 59 Status: SMPTE Errors Menu
- 60 Status: Interrogator Menu
- 61 How to Respond to an Alarm Window
- 61 Setting Alarm Triggers
- 62 Channel: Page 1 and Page 2 Menus
- 62 Channel: Page 1 Menu
- 64 Channel: Page 2 Menu
- 65 Channel: 3D Control Menu
- 67 Channel: Lamp Per Channel Menu
- 68 Channel: Lens Menu
- 69 Channel: Lens Menu Disabled
- 70 Advanced: Preferences Menu
- 71 Advanced: Lamp Menu
- 72 Advanced: Lamp History Menu
- 73 Advanced: Lens Menu
- 74 Advanced: Test Patterns Menu
- 75 Advanced: User Menu
- 76 Admin: Source Menu
- 78 Admin: Screen Menu
- 80 Admin: MCGD Menu
- 82 Admin: TCGD Menu
- 83 Admin: Network Menu
- 84 Admin: General Menu
- 85 Admin: Lamp Menu
- 88 Using the Web User Interface
- 88 Using the CDP
- 88 If the Lamp Fails to Ignite
- 89 Using LiteLOC™
- 89 Adjusting Lamp Position (LampLOC™)
- 91 When to Replace a Lamp
- 91 Lamp Rotation
- 91 Maintaining Footlamberts
- 92 Focus
- 92 Offsets
- 92 Zoom
- 94 Hardware Instructions
- 94 Web User Interface Instructions
- 96 3D Test Pattern
- 96 Image Breakup
- 96 No 3D Effect
- 96 Ghosting / Cross-talk
- 96 Motion Artifacts
- 96 Single 3D Input Not Working
- 98 Projector Variables: Using an Anamorphic Lens
- 99 Projector Variables: Using a Wide Converter Lens
- 99 Theatre Variables: Masking
- 103 Wear Protective Clothing
- 103 Cool the Lamp Completely
- 105 Filling the Coolant Reservoir
- 107 Lamp Fan
- 107 Igniter
- 108 Airflow Interlocks
- 108 Laminar Airflow Device (LAD)