Parallel Upgrade. Cisco Nexus 7700 18-Slot Switch , Nexus 7000 4-Slot Switch , Nexus 7000 9-Slot Switch , Nexus 7000 10-Slot Switch , Nexus 7000 18-Slot Switch , Nexus 7700 2-Slot Switch , Nexus 7700 6-Slot Switch , Nexus 7700 10-Slot Switch
Add to My manuals32 Pages
advertisement
![Parallel Upgrade. Cisco Nexus 7700 18-Slot Switch , Nexus 7000 4-Slot Switch , Nexus 7000 9-Slot Switch , Nexus 7000 10-Slot Switch , Nexus 7000 18-Slot Switch , Nexus 7700 2-Slot Switch , Nexus 7700 6-Slot Switch , Nexus 7700 10-Slot Switch | Manualzz Parallel Upgrade. Cisco Nexus 7700 18-Slot Switch , Nexus 7000 4-Slot Switch , Nexus 7000 9-Slot Switch , Nexus 7000 10-Slot Switch , Nexus 7000 18-Slot Switch , Nexus 7700 2-Slot Switch , Nexus 7700 6-Slot Switch , Nexus 7700 10-Slot Switch | Manualzz](http://s3.manualzz.com/store/data/059688875_1-544f92e8a9128c0d1008fb9b25e8da34-360x466.png)
Cisco Nexus 7000 Series NX-OS Software Upgrade and Downgrade Guide
Parallel Upgrade
Parallel Upgrade
Parallel Upgrade
Starting with Cisco NX-OS Release 5.2(1), multiple linecards can be simultaneously upgraded, and the infrastructure support is available. This decreases the ISSU time when compared with an ISSU upgrade that is done serially (one card at a time).
To start a parallel upgrade, use the following command: install all kickstart image system image parallel
Up to three linecards can be upgraded in parallel with this command. During the upgrade process, the upgrade of the linecards is displayed in the output as follows:
Non-disruptive upgrading.
[# ] 0%
Module 5 upgrade completed successfully.
.
Module 3 upgrade completed successfully.
.
Module 6 upgrade completed successfully.
.
Non-disruptive upgrading.
[####################] 100% -- SUCCESS
Non-disruptive upgrading.
[# ] 0%
Module 9 upgrade completed successfully.
.
Non-disruptive upgrading.
[####################] 100% -- SUCCESS
Note This command will be ignored for a downgrade to a release below Cisco NX-OS Release 5.2.(1).
Parallel Upgrade with Fabric Extenders
Beginning with Cisco NX-OS Release 6.1(1), a parallel upgrade on the Fabric Extenders is supported if the user types the parallel keyword in the command.
For releases prior to Cisco NX-OS Release 6.1(1), only a serial upgrade of Fabric Extenders is supported.
The upgrade process switches to a serial upgrade even for the I/O modules present. Even if the user types the parallel keyword in the command, the upgrade will be a serial upgrade.
Prerequisites for Upgrading the Cisco NX-OS Software
Upgrading the Cisco NX-OS software has the following prerequisite:
Save, commit, or discard any active configuration sessions before upgrading or downgrading the Cisco NX-OS software image on your device. On a device with dual supervisors, the active supervisor module cannot switch over to the standby supervisor module during the Cisco NX-OS software upgrade if you have an active
4
Cisco Nexus 7000 Series NX-OS Software Upgrade and Downgrade Guide, Release 5.x
OL-20634-05
advertisement
Related manuals
advertisement
Table of contents
- 3 About Software Images
- 4 About In-Service Software Upgrades on Devices with Dual Supervisor Modules
- 5 Virtualization Support
- 6 Parallel Upgrade
- 6 Parallel Upgrade
- 6 Parallel Upgrade with Fabric Extenders
- 6 Prerequisites for Upgrading the Cisco NX-OS Software
- 7 Cisco NX-OS Software Upgrade Guidelines
- 9 Cisco NX-OS Software Downgrade Guidelines
- 10 Upgrading a Device with Dual Supervisor Modules
- 11 Benefits of Using the install all Command
- 12 ISSU Failure Conditions
- 12 Upgrade Procedure Summary
- 13 Detailed Upgrade Procedure
- 15 Upgrading a Device with a Single Supervisor Module
- 16 Upgrade Procedure Summary
- 16 Detailed Upgrade Procedure
- 18 Downgrading from a Higher Release
- 19 Performing a Traditional Upgrade or Downgrade (Chassis Reload)
- 21 Example Outputs from Cisco NX-OS Software Upgrades
- 21 Example Nondisruptive Upgrade of a Device with Dual Supervisors
- 26 Example Disruptive Upgrade of a Device with Dual Supervisors
- 29 Example Disruptive Upgrade of a Device with a Single Supervisor
- 30 Obtaining Documentation and Submitting a Service Request
- 30 Feature History for Software Upgrade and Downgrade