advertisement
4
5
6
1
2
3
Hints for Timer Recording
• If there is a power failure or the VCR is unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If the tape runs out before the end time, the VCR will switch to the Stop mode immediately, eject the tape and the VCR power will be turned off. The TIMER indicator will flash.
• If a tape is not in the VCR or does not have the safety tab, the
TIMER indicator flashes and timer recording cannot be performed. Please insert a recordable tape.
To Stop an Automatic Timer Program already started
Press [STOP/EJECT] on the VCR .
To Check, Correct, or Cancel an Automatic Timer Program
1
2
3
Turn the power on by pressing [POWER].
Select main menu by pressing [MENU].
Select "TIMER PROGRAMMING" by pressing [PLAY] or
[STOP]. Then, press [F.FWD].
4 Select the program number which you want to check by pressing [PLAY] or [STOP]. The details of the selected program appears on the TV screen.
• Go to the digit you want to change by pressing [F.FWD] or
[REW]. Then, enter correct numbers by pressing [PLAY] or
[STOP].
• You may cancel the entire program by pressing [REW] during the program number flashes.
5 Press [C.RESET/EXIT] to exit.
Press [POWER] to return to timer stand-by mode.
6
SPECIAL FEATURES
Copying a Video Tape
You can make copies of video tapes made by friends or relatives for your enjoyment.
Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
Connect the recording VCR(this unit), the playing VCR (another source) and your TV using the following diagram.
Audio/Video cables
(not supplied)
[Recording VCR]
(this unit)
[TV set]
(Use for monitoring)
AUDIO
OUT
LEFT RIGHT
VIDEO
IN
[Playing VCR]
(another source)
AUDIO
L
OUT IN
R
VIDEO
OUT IN
ANT
IN
OUT
RF cable
(supplied)
ANT in
• For best results during dubbing, use the VCR’s front panel controls whenever possible. The remote control might affect the playing VCR’s operation.
• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended.
• You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs in place of the playing VCR.
To Monitor the Recording
1 Turn on the TV and set the TV to channel 3.
If channel 3 is already occupied for broadcasting, change the RF output to CH 4, and change the TV channel to CH4.
(See “RF Output Channel” on page 3 for the detail.)
2 Press [VCR/TV] on the remote control of the recording
VCR so that the VCR/TV indicator comes on.
MTS (Multi-Channel Television Sound) System
When you play a VHS tape, or receive a broadcast on the VCR tuner channel you are watching, the status shown below will appear when you press [DIS-
PLAY] on the remote control. When you record the MTS broadcast signal, you need setting the MTS mode.
STOP 12:00AM
CH 32
STEREO
SAP
SP 0:00:00 HIFI
1)
2)
1 Press [MENU] and select "TV STEREO" or "SAP" by pressing [PLAY] or [STOP]. Then, press [F.FWD] for fix mode. To exit, press [C.RESET/EXIT].
• Although a program may be broadcast in both stereo and second audio, you must select the Recording mode in TV
STEREO or SAP before you record a broadcast.
2 Press [MENU] and select "AUDIO OUT" by pressing
[PLAY] or [STOP]. Then, press [F.FWD]. Next, select
"HIFI" or "MONO" by pressing [PLAY] or [STOP]. To exit, press [C.RESET/EXIT].
• While the VCR is set in HIFI stereo mode, HIFI appears on the TV screen. While the VCR is set in monaural (MONO) mode, HIFI disappears from the TV screen.
MTS Recording / Monitor Mode
Type of broadcast
Regular
(monaural audio)
Display on the
TV screen
-None-
STEREO/SAP
Selection
-Invalid-
Hi-Fi audio track
(2-channel)
L-channel R-channel
Normal audio track
Mono
Mono Mono
Stereo broadcast
STEREO -InvalidL R L+R
Bilingual broadcast
Stereo &
Bilingual broadcast
SAP
STEREO
SAP
TV STEREO*
SAP*
TV STEREO*
SAP*
Main audio program
Sub audio program
L
Sub audio program
Main audio program
Sub audio program
R
Sub audio program
Main audio program
Sub audio program
L+R
Sub audio program
* You must select the recording mode in TV STEREO or SAP before you record a broadcast.
Insert a pre-recorded tape into the playing VCR.
Auto Rewind
Insert a tape with its safety tab into the recording
VCR.
Press [SPEED] on the remote control of the recording
VCR to select the desired recording speed (SP/SLP).
When a tape has reached the end during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the VCR will eject the tape and turn itself to off.
• The VCR will not rewind the tape automatically during timer recording or One Touch Recording.
Select the “L1” or “L2”position on the recording VCR.
See page 3, under “Using AUDIO/VIDEO Input Jacks”.
Press [REC/OTR] on the recording VCR.
Begin playback of the tape in the playing VCR.
Real Time Tape Counter
• This shows the elapsed recording or playback time in hours, minutes, and seconds. (The displayed time will not change during blank portions on the tape.)
• The indication will appear when the tape is rewound further than “0:00:00” on the tape counter.
– 6 – EN
advertisement