advertisement
![Menu Structure and Description of Parameters. Motrona BY340, BY641 | Manualzz Menu Structure and Description of Parameters. Motrona BY340, BY641 | Manualzz](http://s3.manualzz.com/store/data/060075051_1-1a285c377a63aa2743fde186af6c1629-360x466.png)
8.
Menu Structure and Description of Parameters
All parameters are arranged in a reasonable order of functional groups (F01 to F09)
You must only set those parameters which are really relevant for your specific application.
Unused parameters can remain as they actually are.
8.1.
Summary of the Menu
This section shows a summary of the parameter groups, with an assignment to the functional parts of the unit.
Gruppe Funktion Gruppe Funktion
F01 Impulse Scaling F03 Definitions for the Master Encoder
000
001
002
003
F02
Factor 1 (Master)
Factor 2 (Slave)
Reserve
Reserve
Operational Settings
026 Encoder Properties
027 Edge Counting
028 Counting Direction
029 Speed Display Factor
030 Speed Display Divider
031 Speed Display Dec.Point
004 Mode (Betriebsart)
005 Trim Time
F04 Definitions for the Slave Encoder
006
007
008
009
010
011
012
Integration Time
Correction Divider
Factor 1 Scaling
Factor 1 Minimum
Factor 1 Maximum
Sampling Time
Wait Time
032 Encoder Properties
033 Edge Counting
034 Counting Direction
035 Reserve
036 Reserve
037 Reserve
F05 Analog Output Settings
013 Max. Master Frequency
014
015
016
017
018
019
020
Ramp Time
Stop-Ramp Time
Alert 1
Alert 2
Phase Offset*
Slave Pulses Index*
Phase Adjust*
038 Analog Format
039 Offset Correction
040 Gain Correction
041 Max. Correction
042 Offset Total
043 Gain Total
044 Reserve
045 Reserve 021 Master Index Divider
022 Index Window
023 Max. Index Correction
024 Reserve
025 Reserve
*) Parameters for Index Modes are only available with Software version BY34002 and higher
By340_04b_oi_e.doc / Apr-16 Page 19 / 42
F06 Command Assignment
046 Key Up Function
047 Key Down Function
048 Key Enter Function
049 Input 1 Configuration
050 Input 1 Function
051 Input 2 Configuration
052 Input 2 Function
053 Input 3 Configuration
054 Input 3 Function
055 Input 4 Configuration
056 Input 4 Function
057 Reserve
F07 Serial Communication
058 Unit Number
059 Serial Baud Rate
060 Serial Format
061 Reserve
062 Reserve
063 Reserve
F08 Special Functions
064 Input Filter
065 Trigger Threshold 1
066 Trigger Threshold 2
067 Brightness
068 Frequency Control
069 Factor Store Configuration
070 Display Time
071 Reserve
F09 Keypad Protection Codes
072 Protect Group F01
073 Protect Group F02
074 Protect Group F03
075 Protect Group F04
076 Protect Group F05
077 Protect Group F06
078 Protect Group F07
079 Protect Group F08
080 Protect Group F09
081 Reserve
082 Reserve
083 Reserve
084 Reserve
085 Reserve
086 Reserve
087 Reserve
By340_04b_oi_e.doc / Apr-16 Page 20 / 42
advertisement
Related manuals
advertisement
Table of contents
- 4 Safety Instructions and Responsibility
- 4 General Safety Instructions
- 4 Use according to the intended purpose
- 5 Installation
- 5 Cleaning, Maintenance and Service Notes
- 6 Available Models
- 7 Introduction
- 8 Electrical Connections
- 10 Power Supply
- 10 Auxiliary Outputs for Encoder Supply
- 10 Impulse Inputs for Incremental Encoders
- 11 Control Inputs Cont.1 – Cont
- 11 Switching Outputs K1 – K
- 11 Serial Interface
- 11 Analog Output
- 12 Principle of Operation
- 12 Synchronization
- 13 Mechanical Phase and Position Considerations
- 14 Operating Modes
- 15 Keypad Operation
- 15 Normal Operation
- 15 General Setup Procedure
- 16 Direct Fast Access to Speed Ratio Setting
- 17 Change of Parameter Values on the Numeric Level
- 18 Code Protection against Unauthorized Keypad Access
- 18 Return from the Programming Levels and Time-Out Function
- 18 Reset all Parameters to Factory Default Values
- 19 Menu Structure and Description of Parameters
- 19 Summary of the Menu
- 21 Description of the Parameters
- 32 Description of Commands and Outputs
- 32 Commands
- 33 Outputs
- 34 Display of Actual Values
- 35 Steps for Commissioning
- 36 Running the Adjust menu
- 37 Set Directions of Rotation
- 37 Tuning the Analog Output
- 38 Setting of the Proportional Gain
- 38 Hints for final operation
- 39 Appendix for model BY
- 39 Relay Outputs
- 39 Front Thumbwheel Switches
- 40 Technical Specifications & Dimensions
- 41 Dimensions of model BY