- Home
- Domestic appliances
- Large home appliances
- High-pressure cleaners
- Briggs & Stratton
- BSPP 1950 PSI
- Owner's manual
advertisement
BSPP 1950 PSI Pressure Washer
ASSEMBLY
IMPORTANT: Read entire owner’s manual before you attempt to assemble or operate your new pressure washer.
Remove Pressure Washer From
Carton
• Remove the parts bag, accessories, and inserts included with pressure washer.
• Slice two corners at the end of carton from top to bottom so the panel can be folded down flat.
• Remove pressure washer from carton.
Carton Contents
Items in the carton include:
• Main Unit
• Goggles
• High Pressure Hose
• Spray Gun
• Adjustable Nozzle Extension
• Parts Bag (which includes the following):
• Hose Fittings
• Quick Connects
• Maintenance Kit
• Owner’s Manual
• Engine Manual
If parts are missing or damaged, contact the local Briggs &
Stratton service center.
PREPARING PRESSURE
WASHER FOR USE
To prepare your pressure washer for operation, you will need to perform these tasks:
1.
Add oil to engine crankcase.
2.
Add fuel to fuel tank.
3.
Connect high pressure hose to spray gun and pump.
4.
Connect water supply to pump.
5.
Attach nozzle extension to spray gun.
Add Engine Oil and Fuel
• Place pressure washer on a level surface.
CAUTION
Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.
• Refer to engine manual for oil and fuel fill information.
• Damage to equipment resulting from failure to follow this instruction will void warranty.
• Refer to engine owner’s manual and follow oil and fuel recommendations and instructions.
NOTE: Check oil often during engine break–in. Refer to engine owner’s manual for recommendations.
6
BSPP 1950 PSI Pressure Washer
Connect Hose and Water Supply to
Pump
IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.
1. Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 2).Tighten by hand.
Figure 2 — Connect High Pressure Hose to Spray Gun
Figure 5 — Connect the Garden Hose to Water Inlet
Connect high pressure hose here
2. Attach other end of high pressure hose to high pressure outlet on pump (Figure 3).Tighten by hand.
Figure 3 — Connect High Pressure Hose to Pump
6. Connect garden hose (not to exceed 50 feet in length) to water inlet (Figure 5). Pull back on collar of quick connect, slide fitting onto pump and let go of collar. Pull on hose to be sure of a tight connection.
CAUTION
There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.
• Damage to equipment resulting from failure to follow this instruction will void warranty.
7. Turn ON water and squeeze trigger on gun to purge pump system of air and impurities.
WARNING
High pressure spray can cause paint chips or other particles to become airborne.
3. Before connecting garden hose to water inlet, inspect inlet screen (Figure 4). Clean screen if it contains debris or replace if damaged. DO NOT RUN PRESSURE
WASHER IF SCREEN IS DAMAGED.
Figure 4 — Inspect Inlet Screen
Inspect inlet screen, DO NOT use if damaged; clean if dirty.
4. Run water through garden hose for 30 seconds to clean out any debris.
IMPORTANT: DO NOT siphon standing water for water supply. Use ONLY cold water (less than 100°F).
5. Attach female quick connect to garden hose.Attach male quick connect to water inlet on pump (Figure 5).
• Always wear eye protection when using this equipment or in vicinity of where equipment is in use.
• Before starting the pressure washer, be sure you are wearing adequate eye protection.
Checklist Before Starting Engine
Review the unit’s assembly to ensure you have performed all of the following.
1.
Check that oil has been added to proper level in engine crankcase.
2.
Add proper gasoline to fuel tank.
3.
Check for properly tightened hose connections (high pressure and water supply) and there are no kinks, cuts, or damage to high pressure hose.
4.
Provide a proper water supply at an adequate flow.
5.
Be sure to read "Safety Rules" and "How To Use
Pressure Washer" before using pressure washer.
7
advertisement
Related manuals
advertisement
Table of contents
- 2 Safety Rules
- 5 Know Your Pressure Washer
- 6 Assembly
- 8 Operation
- 11 Product Specifications
- 11 Maintenance
- 14 Storage
- 15 Troubleshooting
- 16 Replacement Parts
- 18 Notes
- 19 Warranty