advertisement
PACKING LIST
Main Unit............................................1pc
Li-ion Battery.....................................1pc
AC Power Adaptor.............................1pc
9V Car Power Adaptor.......................1pc
ACCESSORIES LIST
Install the battery into the remote control as illustrated below:
A/V Cable............................................1pc
Remote control with battery.............1pc
Earphone............................................1pc
Carrying Case....................................1pc
+
Lithium Cell
Cr2025
3V sc2
Attach the rechargeable battery pack onto the play's bottom as illustrated below:
BACK VIEW
SIDE VIEW
NOTE:
This unit works either on the battery pack supplied or the AC power: unplug the AC Power adapter from the DC input jack to work on the battery pack (after fully charged); plugging the AC Power adapter while the battery pack is attached initiates the charging of this battery, the charge LED indicator lights up red once, and then turns off (about 5 seconds), after that, the indicator will steady on red. When the battery is fully charged the indicator turns off again. Fully charging a run-out battery pack may take 5 hours or longer. A fully charged battery pack can endure approximately 2.5 hours of continuous DVD playback. This playing time may vary with the surrounding environment, the volume level of the speaker and the battery condition. It is advised that you wait 10-20 minutes before recharging the battery pack if it has turned flat during operation.
Connecting to a car adaptor
IMPORTANT: The 9V car power adaptor is designed for use with vehicles that have a 12V, negative ground electrical system.
WARNING:
Disconnect the car power adaptor when not in use. Not in use in 24V vehicles.
To the cigarette lighter socket
!
!
!
!
CAUTIONS:
!
Use the unit only with 9V car power adaptor, use with other car power adaptor could damage the unit.
The recommended 9V car power adaptor is for use with this unit only. Do not use it with other equipment.
In the interests of road traffic safety, do not operate the unit or view video program while driving a vehicle.
Make sure the unit is fastened securely to prevent from moving outside of the vehicle in an accident
When the inside of the cigarette lighter socket is dirty with ashes or dust, the plug section may become hot due to poor contact.
Be sure to clean the cigarette lighter socket before use.
!
After use, disconnect the 9V car power adaptor from both the unit and cigarette lighter socket.
FUSE REPLACEMENT
FUSE
2
1
2
3
4
5
6
7
8
9
10
11
12
13
OVERVIEW OF THE DVD PLAYER:
1
5
6
7
8
9
10
2
3
4
11 12 13 15
14
RIGHT VIEW
28
29
26
27 25
24
FRONT VIEW
22
23
20
21
18
19
16
17
1. LCD SCREEN
2. L&R SPEAKERS
3. BRIGHTNESS ADJUST KEYS
4. COLOUR ADJUST KEYS
5. AUDIO KEY
6. DISPLAY KEY
7. SUBTITLE KEY
8. F.FWD KEY
9. F.BWD KEY
10. VOLUME + & - KEYS
11. DISC COVER
12. LOCK KEY
13. DISC COVER OPEN KEY
14. NAVIGATION UP KEY
15. NAVIGATION LEFT KEY
16. NAVIGATION DOWN KEY
17. ENTER KEY
18. NAVIGATION RIGHT KEY
19. SETUP KEY
20. PLAY/PAUSE KEY
21. STOP KEY
22. PREVIOUS KEY
23. NEXT KEY
24. DC 9V INPUT SOCKET
25. POWER ON/OFF SWITCH
26. COAXIAL SOCKET
27. S-VIDEO SOCKET
28. A/V OUTPUT SOCKET
29. PHONES SOCKET
30. REMOTE SENSOR
31. POWER INDICATOR
31 30
GET A QUICK GLANCE AT
THE REMOTE CONTROLLER
POWER DISPLAY SETUP
TFT ON/OFF
1
VOLUME
4
REPEAT
1/ALL
MENU
7
SUBTITLE
0
PLAY
2
5
8
+10
3
6
9
CLEAR
STOP
TITLE SELECT
AUDIO PAUSE/STEP SLOW
F.BWD
F.FWD
PREV NEXT
ANGLE ZOOM PROGRAM SEARCH
14
15
16
17
18
19
20
21
22
23
24
25
26
1. POWER button
2. VOLUME buttons
3. REPEAT 1/ALL button
4. MENU button
5. SUBTITLE button
6. PLAY button
7. TITLE button
8. AUDIO button
9. PAUSE/STEP button
10. F.BWD button
11. F.FWD button
12. ANGLE button
13. ZOOM button
14. DISPLAY button
15. SETUP button
16. TFT ON/OFF button
17. NUMERIC buttons
18. CLEAR button
19. STOP button
20. SELECT button
21. NAVIGATION buttons
22. SLOW button
23. NEXT button
24. PREV button
25. SEARCH button
26. PROGRAM button
3
USING THE REMOTE CONTROLLER:
NOTE:
The operating range of this remote controller may vary according to the brightness of the room.
Avoid bright light (sunshine or artificial light) aiming directly at the remote sensor. This may cause the remote controller not to work properly.
Do not block the remote controller from the remote sensor by solid objects placed between them.
Use of this remote controller while operating the remote controller of another appliance is not recommended as such operation may cause the remote controller not to work reliably.
REMOTE SENSOR
7 m
30 30
INFRARED EMITTER OF REMOTE CONTROLLER
IMPORTANT:
Uninstall the battery when the player is not to be used for a long period of time to prevent battery from leaking, which may result in harm.
USING THE AC ADAPTER:
Always turn off the DVD player via the Power on/off Key prior to connecting or disconnecting the AC ADAPTER.
Be sure to use the supplied AC adapter. Using a different type of adapter may cause malfunction or damage to the product.
When the AC adapter is used for prolonged periods of time, it may heat up. This is normal and is not a cause for concern.
When not using the adapter, unplug it from the wall outlet.
Keep the AC adapter free from moisture, cold, and dust. Otherwise, a risk of fire or electric shock may be resulted in.
To power outlet
WARNINGS:
Only use the AC adapter supplied with this player.
Be sure to unwind the AC adapter cable (DC output cable) before using, as electromagnetic interference may cause problems with other devices.
Always turn off the DVD player when inserting or removing the AC adapter.
Before storing the battery pack, make sure it is completely drained.
Be sure to recharge the battery at least once every six months to ensure proper battery life.
4
CONNECT DVD PLAYER TO OTHER APPLIANCES
It is recommended you connect the player to a multi-system TV.
Ensure that this player and other appliances (TV set and amplifier) that will be connected to the player are set to OFF mode and that the AC cords are disconnected from the wall outlet.
Avoid blocking ventilation holes of the connected appliances and make sure air around there can circulate freely.
Read carefully and follow the instructions before connecting other appliances.
Observe the color coding when connecting audio and video cables.
AUDIO R AUDIO L VIDEO IN
S-VIDEO
AV AUDIO/VIDEO INPUT
YUV INPUT
TV SET
A/V cable
S-video cable
(optional)
Coaxial digital audio cable
To coaxial digital audio input connector
Decoder or Amplifier with Dolby Digital
(AC-3/DTS) processing
(All sold separately)
After connection is firmed and securely done, plug AC ADAPTER to an applicable wall outlet and turn on the player.
1
S-VIDEO OUTPUT CONNECTORS
The S-video output connector separates the color (C) and luminance (Y) signals before transmitting them to the TV set in order to achieve a sharper picture. (S-video cable is not supplied)
Use the S-video cable when connecting the player to a TV set equipped with an S-Video input connector for the best picture clarity possible.
2
COAXIAL DIGITAL AUDIO OUTPUT
When a DVD recorded in Dolby Digital/DTS is played, Dolby digital/DTS bitstream is output from the player's OPTICAL digital audio output connector. When the player is connected to a Dolby Digital/DTS decoder , you can enjoy theater-like audio quality at your home. [A coaxial audio cable (not included) is required when an optional Dolby digital/DTS decoder is used.]
HOW TO USE A PAIR OF EARPHONES OR HEADPHONES
You can attach a pair of headphones or earphones with a stereo mini-jack plug to the earphones socket for private listening as illustrated as on the right:
CAUTION:
Listening at high volume for a long moment could damage users' ears
.
NOTE:
1. Turn the Volume down before connecting.
2. The speakers are disconnected once earphones are attached to the
Earphones Socket.
3. Adjust the volume to a comfortable level using the Volume keys.
Adjust the volume
5
OPERATIONS
PREPARATION
Power on the TV set and select video input mode.
Power on the audio system which is connected to the player.
GET STARTED
1. Press POWER switch to turn on the player.
2. Press open key to open the disc tray.
3. Place a disc onto the disc tray.
4. Press CD cover to close the disc tray and the playback starts automatically.
5. When a menu screen appears on the TV, move the navigation buttons or press the numeric buttons to select a preferred track number, then press SELECT button to start playback.
ADJUST THE VOLUME
Press the VOLUME+ button to increase or button to reduce the volume.
VOLUME-
SKIP AHEAD OR BACK
Press NEXT SKIP or PREV SKIP button once during play to skip a chapter(DVD) or a track (Video CD/CD) ahead or backwards.
RAPID ADVANCE/ REVERSE
During playback, press F.FWD button or F. BWD button several times to scan the disc forward or backward at X2, X4,
X8, X20 normal speed.
Press PLAY button to resume normal play.
PAUSE OR STEP PLAY
During playback, press PAUSE/STEP button to pause; in pause mode, each time the PAUSE/STEP button is pressed, the player will only play one frame; to resume normal play, press PLAY button again.
STOP PLAYBACK
Press STOP button during playback to stop playback; the player activates its resume function when STOP is pressed in
STOP mode; press PLAY button again, playback resumes at the point it stopped previously; open the disc tray or press the
STOP button one more time to clear the resume function.
SLOW-MOTION PLAY (DVD/VCD)
Press SLOW button on the remote control during playback, the disc will be played at 1/ 2 normal speed at first, each time this button is pressed, the play speed becomes slower
(down to 1/7 normal speed.)
Press PLAY button, normal play will resume.
REPEAT 1/ALL
Press REPEAT 1/ALL button during play, it will repeat play one chapter/title or repeat all(for DVD disc), or repeat play a track or all tracks (for VCD / CD).
NOTE: repeat 1/all for VCD/CD disc will ONLY work in
PBC OFF mode.
SEARCH FOR PREFERRED SCENE
1. Press SEARCH button during play and highlight the item to be played (Title, Chapter, or Chapter time)by navigation buttons
2. Input the desired number or time via the numeric buttons.
3. Press SELECT button to confirm and the playback from the located scene starts.
4. To exit search menu, press SEARCH button directly.
PROGRAM PLAY(UP TO 16 MEMORIES)
1. Press PROGRAM during playback to display the program menu.
2. Select location(s) to be memorized via navigation buttons and then enter desired Titles/Chapters numbers via numeric buttons.
Note: Inputting leading zero is not necessary. Press +10 key to be on the tenth chapter/title/track. If the chapter/title/track number is behind the cardinal 10, press +10 key first and then the unit digit. Some figure inputs may be useless, because it 's greater figure than total title/chapter/track number on the disc.
Example: Track 3, press "3"
Track 12, press "+10" and then "2"
Track 21, press "+10" twice and then "1"
3. To start programmed playback, select PLAY on the menu; pressing PROGRAM button again to exit programming.
4. To clear programmed items, select the items and then press
CLEAR button on the remote control. To clear all items, select the <CLEAR> on the menu, and then press SELECT button on remote control.
5. You can also cancel program mode by clearing all the items in the program menu.
ZOOM PLAY
Press the ZOOM key continuously to zoom in the picture by
2, 3, and 4 times, zoom out by 1/2, 1/3, 1/4 normal size.
Press this key once more when the picture is at 1/4 size to return to the normal size display.
Scroll to view the enlarged picture using Navigation buttons.
ON SCREEN DISPLAY INFORMATION
When the player is in operation, press DISPLAY button continuously on the remote control, the screen will display parts of information(current disc type, title number, chapter number, playtime, audio language, audio type, subtitle language and multi angle, etc) in a sequence.
CHANGING AUDIO SOUNDTRACK
LANGUAGE(DVD/VCD DISC)
It is possible to change the audio soundtrack language to a different language from the one selected at the initial settings (This operation works only with discs on which multiple audio soundtrack languages are recorded).
Press AUDIO button during DVD disc play, the sound track language changes with the current sound track number shown on the TV screen.
Pressing AUDIO button during VCD disc play will change audio output mode: MONO L, MONO R and stereo.
NOTE: When no soundtrack languages are recorded, pressing this button will not work.
6
OPERATIONS
MULTI-ANGLE VIEWING (DVD ONLY)
Press ANGLE button during playback to display the number of angles being played and then select a desired angle to view the scene.
Note: only the DVDs shot with multi-angle scenes have this function.
CHANGING SUBTITLE LANGUAGE (DVD ONLY)
Press SUBTITLE button during playback, the subtitle language shown on the screen will change as a response to each press;
When the desired language appears, release the button to view the subtitle in that language.
Note: this function only works on the DVDs recorded with multi-language subtitles.
ENJOYING VIDEO CDS WITH PBC FEATURE
After loading a VCD 2.0/1.0 with PBC, the TV screen shows the Disc formats and then a menu.
Select desired track by means of numeric buttons: use one corresponding key of numeric buttons 1~ 9 to choose track 1 to track 9 ; 0 key to choose track 10; If the track number exceeds 10, press +10 button first, and then numeric buttons
1 ~ 9.
During playback, press MENU button to return main menu(DVD).press this button to select PBC ON/OFF mode(VCD)
TITLE button Play the title (DVD)
LCD ON/OFF Press the TFT ON/OFF button to turn on or off the LCD display.
MP3 PLAYBACK
1.
Load the Mp3 disc onto the disc tray and the TV screen will show all its folders after a few seconds.
2. Select the folder you want by the navigation buttons and then SELECT button to confirm.
3. The files in this folder are displayed and select your
4.
favourable song via navigation buttons and press SELECT button to start playback.
Press NEXT and PREV button to select track directly.
5.
Press REPEAT 1/all button change play mode.
REPEAT 1- repeat one file.
REPEAT DIR- repeat all tracks in the current album
REPEAT ALL- repeat all tracks in current disc.
REPEAT OFF-cancel repeat modes.
KODAK PICTURE CD / JPEG CD PLAYBACK
Slide show of Kodak Picture CD after being loaded begins automatically;
Folders of JPEG picture CD after being loaded are displayed on the TV screen; use the navigation buttons to select the desired folder and then press SELECT button to confirm.
The files in this folder are displayed and you can select your favourable pictures using the up/down navigation buttons and press SELECT button to start playback.
Preview of the picture will be displayed while you scroll across the filenames.
KODAK PICTURE CD / JPEG CD OPERATIONS
1. PLAY MODES
Press 1/all button during play to change the play modes.
REPEAT 1- repeat one file
REPEAT DIR- repeat all picture in the current album
REPEAT ALL- repeat all pictures in current disc.
REPEAT OFF- cancel repeat modes.
During playback, press STOP to enter preview mode.
7
2.
SKIP TO NEXT/PREVIOUS PICTURE
Press NEXT button to skip to the next picture or PREV button to the previous picture.
If no key is pressed for a few seconds, it will skip to next picture automatically.
3.
PICTURE ROTATIONS
Press RIGHT and LEFT navigation buttons to rotate the picture Clockwise and anti-clockwise respectively.
4.
PICTURE FLIPS
Press UP navigation button to flip the picture vertically.
Press DOWN navigation button to flip the picture horizontally
5.
PICTURE ZOOM IN/OUT
Press ZOOM button continuously ,the picture zooms in by 2,
3, 4 times or zooms out by 1/2, 1/3, 1/4 the original size.
Press this button once more when the picture getting 1/4 size to return to the normal play.
If the picture is enlarged, you may use the navigation buttons to view blocked parts of the picture.
6.
SLIDE SHOW TRANSITION MODES
During slide show playback, press the PROGRAM button cyclically to select one of the following modes to play.
WIPE TOP
WIPE BOTTOM
WIPE LEFT
WIPE RIGHT
DIAGONAL WIPE LEFT TOP
DIAGONAL WIPE RIGHT TOP
DIAGONAL WIPE LEFT BOTTOM
DIAGONAL WIPE RIGHT BOTTOM
EXTEND FROM CENTER H
EXTEND FROM CENTER V
COMPRESS TO CENTER H
COMPRESS TO CENTER V
WINDOW H
WINDOW V
WIPE FROM EDGE TO CENTER
RANDOM
NONE
COLOR AND BRIGHTNESS ADJUSTMENT(FOR THE
LCD SCREEN)
Use the Color +/- and Brightness+/- keys to adjust the color intensity and brightness respectively.
INITIAL SETTINGS
Initial settings page is for you to make your preferred settings up for your player. Once the initial settings are done they are retained in the CPU of the player until otherwise modified.
COMMON PROCEDURES FOR INITIAL SETTINGS
1. Press SETUP button.
2. Use the navigation buttons to select the item you want to modify, press SELECT button to confirm, setting page with further setting items displayed shows on the TV screen. Again use navigation buttons to make changes.
Press again SELECT button to confirm modifications.
3. Use navigation buttons to switch to another setting on the main setting page.
4. Press SETUP button to exit main setting page.
INITIAL SETTINGS
1.SYSTEM SETUP
TV SYSTEM
LCD MODE
TV TYPE
PASSWORD
RATING
DEFAULT
EXIT SETUP
1.1 TV SYSTEM - It is used to select the TV mode.
Options: NTSC / PAL/ AUTO
Please select this option as per your TV set.
1.2
LCD MODE - It is used to select the LCD MODE.
Options: 4:3 16:9
1.3 TV TYPEit is used to select the TV scan mode, please set as per your TV set.
Options: 4:3PS :
4:3LB :
Normal Pan & scan mode normal Letter box mode
16:9 : 16:9 wide screen mode
1.4 PASSWORD/CHANGE - input password to unlock the system. The steps are as follows:
1.4.1 Enter SYSTEM SETUP , select the PASSWORD item by scrolling the down navigation button, and then press the right navigation button to select the input box.
1.4.2 Input user's password"0000" to unlock it, in this case, select the input box again to change the password by inputting another new four numeric numbers and then press SELECT button to confirm. When the password is changed, you are needed to input the new one to unlock the system.
1.4.3 Once you forget your own password, use the supervisor's password "8200" to unlock it.
NOTE : If wrong password was input in unlock status, the system will lock.
1.5 RATING Set the rating of this player. If you want to change the rating of parental lock, please input the password to unlock first.
Options: 1 KID SAFE/2 G/ 3 PG/ 4 PG 13/ 5 PG-R/ 6R/7
NC-17/ 8 ADULT
1.6 DEFAULT Reset to factory settings.
Options: RESTORE
2. LANGUAGE SETUP
OSD LANGUAGE
AUDIO LANG
SUBTITLE LANG
MENU LANG
EXIT SETUP
3. AUDIO SETUP
AUDIO OUT
EXIT SETUP
3.1 AUDIO OUT Set digital output code format.
Options:
SPDIF/OFF: I f you are not connecting to an amplifier via digital output, please select this option.
SPDIF/RAW: Used in general home theatre, select this can output 5.1 channels audio.
SPDIF/PCM: S elect this it can only output 2 channel, but you will get higher quality audio output.
4. VIDEO SETUP
BRI
CON
HUE
SATURATION
EXIT SETUP
4.1 BRI-- to set the brightness for the display.
Options: 0/2/4/6/8/10/12
4.2 CON--to set the contrast effect for display.
Options: 0/2/4/6/8/10/12
4.3 HUE--to set the colour impression for display.
Options: -6/-4/-2/0/+2/+4/+6
4.4 SATURATION--to set the saturation level for display.
Options: 0/2/4/6/8/10/12
5. SPEAKER SETUP
DOWNMIX
EXIT SETUP
2.1 OSD LANGUAGE It is used to select different On Screen
Display language for different user.
Options: ENGLISH
(The number of these options depends on the customer's need.)
2.2 AUDIO LANG select preferred audio language.(DVD only, need disc software support)
2.3 SUBTITLE LANGSelect preferred subtitle language.
(DVD only, need disc software support)
2.4 MENU LANG Select preferred disc menu language.
(DVD only, need disc software support)
5.1 DOWNMIX
Options: LT/RTLeft/Right mix mode
STEREOStereo mode
8
advertisement