- Computers & electronics
- Audio & home theatre
- Remote controls
- RCA
- RCU600M - Universal Remote Control
- User manual
Secondary Key Descriptions for AUDIO Operations. RCA RCU600M - Universal Remote Control
Add to My manuals16 Pages
RCA RCU600M - Universal Remote Control takes control of your home theater equipment with its ability to operate up to 6 devices, including TVs, VCRs, DVD/CD systems, satellite receivers, cable boxes, and audio systems. It features dedicated keys for each component, simplifying operation, and a large, backlit keypad for easy navigation even in low-light conditions. The remote also offers advanced functions like sleep timer, on-screen menu access, and code search capabilities for easy programming.
advertisement
RCU600M_IB_resized.qxd 3/24/04 4:10 AM Page 5
Secondary Key Descriptions For AUDIO Operations
Certain keys on the six-component universal remote have dual functions. Secondary key functions are printed in blue on the remote and are used for AUDIO operations.
Not all functions work for all brands. Experiment with your AUDIO system to determine which functions work with your components.
See the enclosed AUDIO Code List to operate your brand of equipment.
Press the AUDIO key to enable the Audio Mode.
AM•FM: allows you to select the AM•FM band on your AUDIO receiver.
CD , TAPE , TUNER , TV , VIDEO 1 , VIDEO 2: For some AUDIO systems, these keys will select the corresponding component input.
DELAY, ON , DELAY+: increases or decreases the delay between the surround and main speakers when the receiver is in the Surround Sound Mode.
DSP ON•OFF: enables the receiver’s Digital Signal Processing Mode.
DSP MODE: When the DSP mode is enabled, pressing this key allows the user to cycle through the various DSP Modes.
FRONT , CENTER , REAR , TEST: adjusts the levels of the front, center, and rear speakers used with LEVEL+/ LEVEL. The test tone must be enabled first by pressing the TEST key.
FUNCTION: selects the different AUDIO input components. The number keys also select the function labeled below the keys when in Audio Mode.
LEVEL+/LEVEL-: sets the level of the speakers during Test Tone Mode.
PRESET: cycles through preset channels while the Tuner input on your
AUDIO system is active.
Program for TV—Direct Entry Method
In order for the six-component universal remote to control your TV, you must program it with the TV code that matches your TV. These instructions explain the preferred method of programming the remote—the Direct Entry method. To program your remote to control your TV, follow these steps:
1. Manually turn on the TV.
2. Locate the enclosed TV Code List. Find your brand of TV.
Note : If your brand is not listed, use one of the Code Search methods to program this remote control. (See section on
Code Search.)
3. Press and hold the CODE SEARCH key until the indicator light illuminates.
Then release the CODE SEARCH key.
4. Press and release the TV key. The indicator light blinks and then remains lit.
5. Use the number keys to enter the first code listed for your brand. After you enter a valid three-digit code, the indicator light turns off.
Note : If you enter an invalid code, the
LED flashes rapidly for two seconds.
Start over at step 3.
6. Aim the remote at your TV and press the ON•OFF key. If your TV turns off, you have found the correct code.
7. Enter the code in the box provided on this page for future reference.
8. If your TV doesn’t turn off, repeat steps
3-6 above, entering the next code for your brand.
If none of the codes work or your brand is not listed, use one of the Code Search methods to program this remote.
(See Code Search section on page 10.)
CODE
SEARCH
INDICATOR
LIGHT
TV (BLINK)
ON•OFF
TV CODE
(OFF)
5
advertisement
Related manuals
advertisement
Table of contents
- 2 Product Diagram
- 3 Introduction
- 3 Battery Information and Installation
- 3 Key Descriptions
- 4 Primary Key Descriptions for VIDEO Operations
- 5 Secondary Key Descriptions for AUDIO Operations
- 5 Program for TV—Direct Entry Method
- 6 Program for VCR—Direct Entry Method
- 7 Program for DVD/CD Systems—Direct Entry Method
- 7 Program for SATELLITE—Direct Entry Method
- 8 Program for CABLE BOX—Direct Entry Method
- 9 Program for AUDIO Systems—Direct Entry Method
- 9 Operating AUDIO System Functions
- 10 Code Search Methods
- 10 Manual Code Search
- 10 Auto Code Search
- 11 Code Retrieval
- 11 Sleep Feature
- 11 Programming the Sleep Timer
- 11 Canceling the Sleep Timer
- 12 On-screen Menus
- 12 Accessing a Menu System
- 12 Highlighting and Selecting Menu Items
- 12 Exiting a Menu System
- 14 Troubleshooting
- 15 Limited 90-Day Warranty