advertisement
2. TECHNICAL DATA
2.1 Functional Data
Tuning
Self-tuning range
Sensitivity
Frequency
Relay Outputs
Presence Relay
Presence Time
Delay Time
Fault Output
Fully Automatic
20 to 1500 µH
Four step switch selectable
High 0.02 %
∆
L/L
Medium High 0.05 %
∆
L/L
Medium Low 0.10 %
∆
L/L
Low 0.50 %
∆
L/L
Four step switch selectable
Frequency dependent on loop size
Presence Relay
Fault Relay
Fail-safe
Switch selectable:
1 Second
4 Minutes
40 Minutes
No fixed time-out (dependant on inductance change) Approx.
1 hour for 3 %
∆
L/L
Switch selectable:
0 Seconds
10 Seconds
20 Seconds
30 Seconds
Separate fault monitor output relay
Operates under the following conditions:
1. Loop open/short circuit
2. Detector/power fault
Response Times
Drift Compensation Rate
Visual Indications
Reset
Surge protection
Turn – on 60 milliseconds
Turn – off 60 milliseconds
Approx. 1 %
∆
L/L per minute
1 X Power LED - Red
1 x Channel Status LED - Green
Reset by push button on front of enclosure
Loop isolation transformer, gas discharge tubes, and Zener
Diode clamping on loop input
301UM0031_01 TD136 Enhanced Vehicle Detector User Manual Page: 6 of 29
advertisement
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION
- 6 TECHNICAL DATA
- 6 Functional Data
- 7 Electrical Data
- 7 Environmental Data
- 7 Mechanical Data
- 8 Approvals
- 9 OPERATING PROCEDURE
- 9 Hardware Set-Up
- 9 Switch Setting Selections
- 9 Frequency Switch
- 10 Sensitivity
- 10 Automatic Sensitivity Boost
- 10 Filter Mode
- 10 Pulse Relay
- 10 Presence Time
- 11 Reset Switch
- 11 Power Fail (Option)
- 11 Front Panel Indicator
- 12 PRINCIPAL OF OPERATION
- 12 Detector Tuning
- 12 Detector Sensitivity
- 13 Modes of Operation
- 13 Response Times
- 14 INSTALLATION GUIDE
- 14 Product Safety Requirements
- 14 Operational Constraints
- 15 Loop and Feeder Specification
- 16 Sensing Loop Geometry
- 16 Loop Installation
- 18 CONFIGURATION
- 18 PD131 Enhanced Detector - Order number 301FT
- 19 PD132 Enhanced Detector - Order number 301FT
- 19 PD134 Enhanced Detector - Order number 301FT
- 20 APPLICATIONS
- 21 CUSTOMER FAULT ANALYSIS
- 21 Fault Finding
- 22 DU100 – Detector Diagnostic Unit
- 22 Interpretation of DU100 Readings
- 22 8.3.1 Frequency
- 23 8.3.2 Frequency drift
- 23 8.3.3 Sensitivity
- 23 8.3.4 Time
- 24 8.3.5 Crosstalk
- 24 Functional Test
- 25 APPENDIX A - FCC ADVISORY STATEMENT
- 26 APPENDIX B – INSTALLATION OUTDOORS
- 26 IEC 60950-22:2005 – Outdoor cabinet
- 26 IEC 60950-22:2005 - Northern Europe
- 26 IEC 60950-1:2005 – Overvoltage Category
- 27 APPENDIX C –REQUEST FOR TECHNICAL SUPPORT FORM
- 34 INTRODUCTION
- 35 TECHNICAL DATA
- 35 Functional Data
- 36 Electrical Data
- 36 Environmental Data
- 37 Mechanical Data
- 37 Approvals
- 38 OPERATING INSTRUCTIONS
- 38 Hardware Set-up
- 38 Switch Setting Selections
- 38 Frequency Switch
- 39 Sensitivity
- 39 Presence Time
- 40 Delay Time
- 40 Reset Switch
- 40 Front Panel Indicator
- 41 PRINCIPAL OF OPERATION
- 41 Detector Tuning
- 42 Detector Sensitivity
- 42 Modes of Operation
- 42 Response Times
- 43 INSTALLATION GUIDE
- 43 Product Safety Requirements
- 43 Operational Constraints
- 44 Loop and Feeder Specification
- 45 Sensing Loop Geometry
- 45 Loop Installation
- 47 CONFIGURATION
- 47 Vehicle Detector - Order number 305FT
- 49 APPLICATIONS
- 50 CUSTOMER FAULT ANALYSIS
- 50 Fault Finding
- 51 DU100 – DETECTOR DIAGNOSTIC UNIT
- 51 Interpretation of DU100 readings
- 51 8.2.1.1 Frequency
- 52 8.2.1.2 Frequency drift
- 52 8.2.1.3 Sensitivity
- 52 8.2.1.4 Time
- 53 8.2.1.5 Crosstalk
- 53 Functional Test
- 54 APPENDIX A - FCC ADVISORY STATEMENT