PRE-OPERATION CHECKS. Sea-doo LRV 2002, 2003 LRV DI, LRV DI, LRV

Add to My manuals
88 Pages

advertisement

PRE-OPERATION CHECKS. Sea-doo LRV 2002, 2003 LRV DI, LRV DI, LRV | Manualzz

smo2003-005a.book Page 41 Friday, November 1, 2002 8:25 AM

PRE-OPERATION CHECKS

WARNING

The pre-operation check is very important prior to operating the watercraft.

Always check the proper operation of critical controls, safety features and mechanical components, before starting as listed hereinafter. If not done as specified here, severe injury or death might occur. Bring all safety equipment required by local laws.

Some of the following items may not have been previously covered in this guide, however they will be described in the MAINTENANCE or SPECIAL PROCEDURES section. Please refer to these sections to have more detailed information.

WARNING

Engine should be off and the safety lanyard should always be removed from its post prior to verifying any of the following points. Only start watercraft once all items have been checked and operate properly.

Hull

Jet pump water intake

Bilge

Battery

ITEM OPERATION

Inspect.

Inspect/clean.

Drain. Ensure plugs are secured.

Inspect tightness of cables and retaining strap(s).

Refill.

Fuel tank and oil reservoir

Engine compartment

Steering system

Throttle system

Check fuel line connections for tightness.

Verify for any fuel leak/odor.

Check operation.

Check operation.

Shifter system

Safety lanyard and engine start/stop button

Check operation.

Storage compartment covers and seat

Ensure they are closed and latched.

Check operation.

NOTE: See the detailed instructions hereinafter.

41

smo2003-005a.book Page 42 Friday, November 1, 2002 8:25 AM

Hull

Inspect hull for cracks or damage.

Jet Pump Water Intake

Remove weeds, shells, debris or anything else that could restrict the flow of water and damage cooling system or propulsion unit. Clean as necessary.

If any obstruction can not be removed, refer to an authorized SEA-DOO dealer for servicing.

F01J3ZY

TYPICAL

1. Inspect this area

1

Inspect leading edges of the impeller, if they have nicks or bends performance will be greatly reduced.

Bilge

Should water be present in the bilge, tilt the watercraft to the rear and unscrew drain plugs to completely empty the bilge.

Secure bilge drain plugs.

WARNING

Make sure drain plugs are properly secured prior to launching the watercraft in water.

Battery

WARNING

Verify tightness of battery cables to their posts and condition of battery retaining strap(s)/fasteners. Do not charge or boost battery while installed.

Fuel Tank and Oil Reservoir

With the watercraft horizontal, fill the fuel tank to specified level.

Check the oil level and refill reservoir as necessary.

Check fuel tank and oil reservoir retaining straps/fasteners.

Engine Compartment

WARNING

Should any leak or gasoline odor be present, do not start the engine.

Refer to an authorized SEA-DOO dealer before use.

Steering System

Assisted by another person, check steering operation for free movement.

When the handlebar is horizontal, the jet pump nozzle should be in the straight ahead position. Ensure the jet pump nozzle pivots easily and in the same direction as the handlebar.

WARNING

Check handlebar and corresponding steering nozzle operation before starting.

42

smo2003-005a.book Page 43 Friday, November 1, 2002 8:25 AM

Throttle System

Check throttle lever for free and smooth operation. It should return to its initial position immediately after it is released.

WARNING

Check throttle lever operation before starting the engine.

Shifter System

Check reverse gate operation for free movement. With shift lever in forward position, the gate should be in upward position. With the shift lever in neutral position, gate should be in middle position. With shift lever in reverse position, gate should be in downward position.

WARNING

Verify the reverse gate operation before starting the engine.

Storage Compartment

Covers and Seat

Ensure they are closed and latched.

WARNING

Make sure seat is securely latched.

Safety Lanyard and Engine

Start/Stop Button

Position shift lever in neutral. Ensure that both switches operate properly. Start engine and stop it using each switch individually.

WARNING

Should the safety lanyard cap is loose or fail to remain on its post, replace it immediately in order to avoid unsafe use.

43

advertisement

Related manuals

Download PDF

advertisement