“Heat Strip” - Heat Strip Mode (Select Models). Oliver Travel Trailers Legacy Elite I, Legacy Elite II
Add to My manuals298 Pages
advertisement
DOMETIC THERMOSTAT
MODE DESCRIPTION
c. “Auto”: Fan speed will vary depending on difference between the temperature set-point and room air temperature. The compressor and the fan will cycle On and Off with thermostat. Compressor shuts off first followed by fan in approximately 15 seconds. See “B.
Auto Fan” on page (8) for more information.
2. This mode of operation is a customer option usually selected when temperatures are below
70ºF and customer needs warmth in living space rather than cool down. This reverses refrigerant flow in the air conditioner, causing warm air to be dispensed inside rather than cold, and cold air is dispensed outside rather than warm.
3. This mode of operation can cause a dilemma where the outside coil, which is now dispensing cold air can freeze up due to cold air blowing across the coil mixed with outside temperature. A system freeze up can render heat pump inoperable. There is a defrost feature that will prevent this from happening. See “D. Defrost Cycle” on page (9) for more information.
E. “Heat Strip” - Heat Strip Mode (Select Models)
1. In Heat Strip Mode, system will cycle heat strip On and Off based on room air temperature and temperature set-point on CT thermostat. There are 3 fan speeds in Heat Strip Mode.
a. “Low”: Fan operates continuously at low speed. Heat strip cycles On and Off.
b. “High”: Fan operates continuously at high speed. Heat strip cycles On and Off.
c. “Auto”: Fan operates in low speed and will cycle On and Off with thermostat.
F. “Fan” - Fan Mode
1. There are 3 fan speeds in Fan mode.
a. “Low”: Fan operates continuously at low speed. b. “High”: Fan operates continuously at high speed. c. “Auto”: Fan is Off.
SPECIAL FEATURES
A. Capacitive Touch Interface
The capacitive touch interface provides a clean, modern user interface.
Capacitive touch interface requires skin contact to function, therefore it will NOT work through gloves, bandages, etc...
Moisture, including wet fingers, on the capacitive touch interface can cause sensors to become unresponsive until the water evaporates.
60
B. Auto Fan
When auto fan is selected fan speed will vary depending on room temperature and temperature set-point. In auto fan compressor and fan cycle On and Off with thermostat.
When difference is:
> 5ºF Fan operates on HIGH
< 4ºF Fan operates on LOW
8
advertisement
Related manuals
advertisement
Table of contents
- 29 Notes on using the manual
- 31 Specifications
- 31 Components
- 32 Installation
- 32 Operation
- 33 Cleaning
- 34 Winterization and storage
- 35 10 Troubleshooting
- 36 12 Customer service
- 42 Explanation of symbols and safety instructions
- 43 2 General information
- 43 3 Intended use
- 44 4 Installation
- 47 5 Operation
- 51 6 Maintenance, cleaning, and storage
- 51 7 Disposal
- 52 8 Replacement parts
- 52 Limited two-year warranty
- 54 INTRODUCTION
- 54 DOCUMENT SYMBOLS
- 55 FAMILIARIZATION
- 55 Features
- 55 System Initialization
- 55 Factory Preset Settings
- 55 Quick Reference
- 56 PROGRAMMING AND OPERATION
- 56 On / Off
- 56 Temperature Format ºF / ºC
- 57 Inside Temperature
- 57 Mode Selection
- 58 Fan Speed
- 58 Temperature Set-Point
- 59 MODE DESCRIPTION
- 59 “Off” - Off Mode
- 59 “Cool” - Cool Mode
- 59 “Furnace” - Furnace Mode
- 59 “Heat Pump” - Heat Pump Mode (Select Models)
- 60 “Heat Strip” - Heat Strip Mode (Select Models)
- 60 “Fan” - Fan Mode
- 60 SPECIAL FEATURES
- 60 Capacitive Touch Interface
- 60 Auto Fan
- 61 Compressor Time Delay
- 61 Defrost Cycle
- 61 Low Ambient Heat Pump Lock Out
- 61 Power Interruption
- 61 LCD Error Code
- 62 GENERAL INFORMATION
- 62 Frost Formation On Cooling Coil
- 62 Heat Gain
- 62 Condensation
- 63 MAINTENANCE
- 63 Air Filter
- 63 CT Thermostat
- 63 SERVICE - UNIT DOES NOT OPERATE