Remote I/O Modules
Characteristics of Ethernet Remote I/O Modules
NOTE: To help prevent dust from entering the unused Ethernet ports on these adapter modules, cover the ports with the stopper:
External Ports
Two of the Ethernet ports allow implicit I/O exchanges with a remote I/O scanner adapter. (An implicit I/O exchange has a maximum frame size of 1400 bytes.) The ports can be implemented alone or in redundant mode.
You can use a maximum of 31 adapters in a single Ethernet remote I/O network.
For network topology planning, refer to the Quantum Ethernet I/O System
Planning Guide .
These modules have up to three 10/100 Base-T Ethernet ports:
Port
SERVICE
DEVICE
NETWORK
Description
The SERVICE port allows the diagnosis of Ethernet ports and provides access to external tools and devices (Control Expert, ConneXium Network Manager, HMI, etc.). The port supports these modes:
• access port (default): This mode supports Ethernet communications.
• port mirroring: In this mode, data traffic from one of the other 3 ports is copied to this port. This allows a connected management tool to monitor and analyze the port traffic.
• disabled
NOTE:
• You can configure the SERVICE port either on line or off line.
• In port mirroring mode, the SERVICE port acts like a read-only port. That is, you cannot access devices (ping, connection to Control Expert, etc.) through the SERVICE port.
• There is no SERVICE port on the BMXCRA31200 adapter module.
Refer to
Service Port Configuration , page 41
.
The DEVICE NETWORK copper port provides:
• connections for remote I/O communications
• cable redundancy
NOTE: Do not connect a device with a speed in excess of 100 Mbps to any port. If the device is configured for a speed that exceeds 100 Mbps, the
Ethernet link may not be established between the device and the module through the port.
Cable Redundancy
Use a daisy chain network configuration that implements the RSTP service to establish redundant communications between the adapter module and a remote I/
O scanner. The adapter operates normally when at least one of the 2 physical paths to the 140CRP31200 is valid. (For network topology planning, refer to the
Quantum Ethernet I/O System Planning Guide .)
Module Specifications
Product Certification
The Quantum EIO head/adapter modules meet these standards:
16 S1A48978.14
Characteristics of Ethernet Remote I/O Modules
Remote I/O Modules
Environmental Requirements
Parameter protection protection class over voltage class operating temperature storage temperature sinusoidal vibration
Reference
EN 61131-2
IEC 60527
EN 61131-2
EN 61131-2
IEC 60068-2-1
Ab&Ad (cold)
IEC 60068-2-2
Bb&Bd (cold)
IEC 60068-2-1
Ab&Ad (cold)
IEC 60068-2-2
Bb&Bd (cold)
IEC 60068-2-6fC
EN 61131-2
IEC 60068-2-27Ea operating shock altitude free fall, random
(packaged)
UL (UL508)
CSA (CSA22.2 no. 142)
C-tick
Hazardous locations (Cl1 div 2)
IEC61000-4-16
EMI EN 55011
CE
EN 61131-1
IEC 61131-2 (zone B and zone C, except surges on AC: zone B only)
Quantum EIO modules conform to these product certification and marine classification authorities:
Key
ABS
BV
DNV
GOST
GL
LR
RINA
Certification Body
American Bureau of Shipping
Bureau Veritas
Det Norske Veritas
Gosudarstvennyy Standart
Germanischer Lloyd
Lloyd's Register
Registro Italiano Navale
Country
United States
France
Norway
Russia
Germany
United Kingdom
Italy
The electrical isolation within a Quantum EIO system modules complies with the
1500 Vac/2250 Vdc 60s from IEEE 802.3 2008.
EN 61131-2
IEC 60068-2-32
Specification
IP20 protection class 1 category II
0 ... 60° C
-40 ... 85° C
• .5 ... 8.4 Hz at 3.5 mm constant amplitude
• 8.4 ... 150 Hz at 1g constant acceleration
• 10 cycles at sweep rate of 1 oct/min
30 g peak, 11 ms, half-sine wave, 3 shocks in each direction (+ and -) for each of the 3 principle axes
0 ... 5000 m maximum during operation. For altitudes > 2000 m, reduce the operating temperature by 6° C for each additional 1000 m.
5 random drops from 1 m onto flat surfaces
S1A48978.14
17
