XTEL-CAD Operating Modes 2
__________________________________________________________________________________________
2.2
Software Installation
2.2-1 Installing the Software Key Module
Fit the software key module into the empty location in the software key module holder.
Ensure that the terminal is powered-down before performing this operation.
Note
The software key module contains the right of use required to run the XTEL-CAD program. The Key
Manager, supplied with the X-TEL and MINI X-TEL Software Workshops, lets the user transfer this right of use to the work key module, freeing a software key module holder slot. For detailed information on how to use the Key Manager, refer to the appropriate TXT L BASE V5E or
TXT L BJR V5E documentation.
__________________________________________________________________________________________
2.2-2 Preliminary Operations
Before installing XTEL-CAD on the hard disk, it is recommended that the user:
• Make a copy of the program disk and that this disk be used for all installation procedures to avoid accidental damage to the original. Once it has been copied, the original disk should be kept in a safe place,
• Carefully read the licence and guarantee certificates that come with this program and that detail the conditions of use and the restrictions that apply to copying and installing the program.
Important
The XTEL-CAD program diskette is supplied write protected. Do not change the position of the write protect tab on the diskette.
__________________________________________________________________________________________
2.2-3 Installation Conditions
XTEL-CAD runs in the X-TEL or MINI X-TEL Software Workshop environment.
The Software Workshop must already be installed on the microcomputer before
XTEL-CAD is installed.
Before installing XTEL-CAD, make sure that at least 350 KBytes of free space is available on the target hard disk partition.
__________________________________________________________________________________________
2 / 3
G
G
__________________________________________________________________________________________
2.2-4 Installation Procedure
Installing XTEL-CAD
An X-TEL or MINI X-TEL V5 Software Workshop must already be installed on the terminal. If this is not the case, first install an X-TEL (TXT L BASE V5) or MINI X-TEL
(TXT L BJR V5) Software Workshop, the:
• Open an OS/2 full screen session, to do so:
With OS/2 1.2 or 1.3.
- Open the Group - Main window,
- Select OS/2 Full Screen. The prompt [C:\] is displayed.
With OS/2 2.1
- Open the OS/2 folder,
- Open Guests,
- Open OS/2 Full Screen. The prompt [C:\] is displayed.
• Insert the TXT LF CAD V5 diskette into the appropriate diskette drive,
• Type the drive identification letter (a: or b:) corresponding to the drive where the diskette is located, then press <Enter> to confirm,
Once the correct prompt (e.g. [a:\] or [b:\] is displayed), type Install and press <Enter> to confirm.
The following screen is displayed:
INSTALLATION LOGICIEL XTEL-CAD
XTEL-CAD SOFTWARE INSTALLATION
(C) TELEMECANIQUE 1991-1993 V5.0
Press <Enter> to continue:
After pressing <Enter>, the XTEL-CAD program files are copied to the various Software
Workshop sub-directories. Once this is done, the following screen is displayed:
CONFIGURATION CHECK...
1
2
The installation procedure can perform a check on the program configuration of the XTEL Software Workshop installed under OS/2.
If you have just completed the last program installation required before starting the XTEL Software Workshop, you can run a complete check on the program configuration. If not, run the complete check once you have installed all XTEL software.
Last installation completed, run configuration check.
Run check later, other programs still waiting to be installed in the
XTEL software workshop.
Your choice:
__________________________________________________________________________________________
2 / 4
XTEL-CAD Operating Modes 2
__________________________________________________________________________________________
After each program installation, it is recommended that the user run a configuration check by selecting 1 from the screen shown on the previous page.
After the check is performed, the program installation procedure is complete and the following screen displayed:
INSTALLATION COMPLETE...
The installation procedure is complete.
XTEL-CAD is now installed in the Telemecanique XTEL Software Workshop.
Press <Enter>:
Enter Returns the user to the OS/2 full screen window.
__________________________________________________________________________________________
2 / 5
G
