advertisement
2 • Front and rear panels—Remote control unit (front panel)
D
CUE key
If a cue point has been stored, the unit will play when the CUE key is pressed, and enter pause mode when this key is released.
E
PLAY/PAUSE key
Changes between playback and pause mode.
The key lights steadily in playback mode, and flashes in pause mode.
If the ENTER key L is pressed and held down, and the PLAY key is pressed at the same time, a “cross play” function is enabled where the deck whose
PLAY key is not pressed will stop playback, and the deck whose PLAY key has been pressed will start playback.
F
JOG dial
Use this to advance or retard the playback position at a maximum resolution of 1 frame. The resolution can be set using the procedure described in 3.3.3, “Cueing using the JOG dial”.
This dial is also used for setting parameter values, etc. as explained elsewhere in this manual (3, “Basic operations” and 4, “Advanced Operations”).
G
Number keys and CLEAR key
Use these number keys for direct entry of numerical values such as direct track search, time search, preset function recall, memory storage, etc.
Use the CLEAR key to reset numeric values.
When the CLEAR key is pressed and held down and the 0 key is pressed, the number keys take on special functions, as explained in 4.6, “Number key modes”.
H
BANK key
Use to select between the five memory banks.
I
PRESET key
Allows the recall of preset functions (see 4,
“Advanced Operations”).
J
MEMORY key
Memorizes the current settings.
K
RECALL key
Recalls the memories.
L
ENTER key
Confirms memory numbers, recall of memories and preset function settings.
M
BPM counter
Shows the tempo (in bpm—beats per minute—from
81 to 161) of the current track, or of the tapped tempo input with the TAP key
N
(see 4.5, “BPM”).
N
TAP key
Set the tempo in bpm manually by tapping the TAP key.
When you press this TAP key, the BPM counter M mode changes to the TAP mode and the TAP LED (to the left of the BPM counter) lights.
You can then adjust the tempo later using the dial F .
Pressing and holding this key for more than 2 seconds resets the value.
Pressing and holding this key and the BPM key together allows the value to be adjusted using the dial.
O
BPM key
Selects either the automatic or tap BPM counter mode.
Clear the tempo by pressing and holding down this key for more than 2 seconds.
P
TEMPO SYNC key
Turns the tempo sync function on and off. When this function is on, the key lights up. The tempo sync function allows the playback tempo of the two decks to be synchronized (see 4.7, “Tempo Sync”).
Pressing this key will adjust the tempo of the deck to the tempo of the material being played on the other deck.
While the deck is “locking up”, the TEMPO SYNC key flashes, and when the sync is locked, the light lights steadily.
Q
BEAT SYNC key
Turns the beat sync function on and off. The beat sync function synchronizes the playback of the decks, so that the beats in the material are synchronized with the beats in the material played back by the other deck (see 4.8, “Beat Sync”).
While the deck is “locking up”, the BEAT SYNC key flashes, and when the sync is locked, the light lights steadily.
R
LOOP key
Switches looping on and off. When looping is enabled, the key lights and the display indicator also lights.
TASCAM CD-302
13
advertisement
Related manuals
advertisement
Table of contents
- 8 Beware of condensation
- 8 Never use a stabilizer
- 8 Handling of discs
- 12 Main unit (front panel)
- 12 POWER switch and indicator
- 12 OPEN keys (1 and 2)
- 12 Disc trays
- 12 Main unit (rear panel)
- 12 OUTPUT jacks
- 12 REMOTE connectors
- 12 jacks
- 12 OPEN key
- 12 TIME key
- 12 SINGLE key
- 12 INDEX key
- 12 SKIP keys
- 12 SEARCH keys
- 13 CUE key
- 13 PLAY/PAUSE key
- 13 JOG dial
- 13 Number keys and CLEAR key
- 13 BANK key
- 13 PRESET key
- 13 MEMORY key
- 13 RECALL key
- 13 ENTER key
- 13 BPM counter
- 13 TAP key
- 13 BPM key
- 13 TEMPO SYNC key
- 13 BEAT SYNC key
- 13 LOOP key
- 14 A and B keys
- 14 SAMPLE key
- 14 IN/OUT keys
- 14 SCRATCH key
- 14 BRAKE key
- 14 + and – keys
- 14 KEY ORIGINAL/RESET key
- 14 TEMPO 8%/16%/32% key
- 14 TEMPO slider
- 14 Remote control unit (rear)
- 14 REMOTE connectors
- 15 TRACK indicator
- 15 Bank indicators
- 15 Loop mode indicator
- 15 REMAIN indicator
- 15 M (memory) indicator
- 15 SINGLE indicator
- 15 PROGRAM indicator
- 15 Time display
- 15 Time address bar
- 15 TEMPO indicator
- 15 KEY indicator
- 15 INDEX indicator
- 15 INCR indicator
- 15 AUTO READY Indicator
- 15 RELAY Indicator
- 15 AUTO CUE Indicator
- 16 Playback
- 16 Pause
- 16 Cross-play
- 17 Auto Cue
- 17 Cueing using the JOG dial
- 17 Cueing using the SEARCH keys
- 17 Cueing using the numeric keys
- 17 Selecting the loop mode
- 18 A-B loop play mode
- 18 Setting A-B loop points
- 18 Playback in A-B loop play mode
- 18 Clearing loop points
- 18 Editing the loop points
- 18 A-B loop duration
- 19 SINGLE loop
- 19 ALL loop
- 20 Tempo (speed) control
- 20 Changing only tempo (speed)
- 20 Key (pitch) control
- 20 percentage
- 20 semitone steps
- 21 Sampling
- 21 Editing the OUT point
- 21 Playback of sampled data
- 21 Playback of sampled data in reverse