advertisement
PLAYING THE DISCS ON OTHER DVD PLAYERS
Finalizing a Disc
You will need to finalize DVD+R, DVD-RW or DVD-R to play them back on other DVD players.
Finalizing may take several minutes up to an hour.
A shorter recording period on the disc will require a longer time period for finalization. Do not unplug the power cord during finalization.
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
TUV
8
SPACE
0
ABC
2
JKL
5
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU
1
2
Press [SETUP].
Use [
K
/
L
] to select “Disc Edit”, then press [OK].
“Disc Edit” menu will appear.
3 Use [
K
/
L
] to select “Finalize”, then press [OK].
4 Use [
K
/
L
] to select “Yes”, then press
[OK].
e.g.) DVD+R, DVD-R
Finalize disc?
Yes
No
Finalizing will start.
s
TITLE
B
Finalizing 90% j B
F
-h g
CHANNEL
+
REC MODE VCR DVD TIMER
To cancel finalizing...
(DVD-RW only)
• To cancel finalizing at step 4, press [STOP
C
] , select
“Yes” with [
K
/
L
] , then press [OK] . Finalizing is canceled and the unit will be in stop mode.
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
Do you want to cancel ?
Yes
No
SEARCH
Note
• Once you have finalized a DVD+R/ DVD-R, you cannot edit or record anything on that disc.
• There is no need to finalize DVD+RW.
• When you insert a DVD-RW finalized with this unit,
“Undo Finalize” will appear instead of “Finalize”.
Disc Edit
Edit Disc Name
Erase Disc
Undo Finalize
Disc Protect ON OFF
To release the finalizing for the disc, select “Undo
Finalize” at step 3.
* DO NOT power off during finalization, this will result in malfunction.
Finalizing 5%
• If appears when pressing [STOP
C
] , you cannot cancel finalizing because the finalizing has been in certain progress.
• When selecting “No” and press [OK] or [RETURN] , finalizing will be continued.
• You cannot cancel finalizing the DVD+R/DVD-R once it has started.
This operation may take a while to be completed.
5 Finalizing is completed.
EN 53
E9M81UD_ZV457MG9.indd 53 2008/05/15 14:31:25
PLAYING THE DISCS ON OTHER DVD PLAYERS
Auto Finalizing
You can finalize discs automatically using this function.
You can use this function to finalize discs after finishing all timer recordings and at the end of the disc space.
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU
1 Press [SETUP] and use [
K
/
L
] to select “General Setting”, then press
[OK].
“General Setting” menu will appear.
2 Use [
K
/
L
] to select “Recording”, then press [OK].
“Recording” menu will appear.
3 Use [
K
/
L
] to select “Auto Finalize”, then press [OK].
4 Use [
K
/
L
] to select “Disc Full” or
“End of Timer Rec”, then press [OK].
Auto Finalize
Disc Full
End of Timer Rec s
TITLE
B
RETURN j B
F
-h g
CHANNEL
+
C
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
5 Use [
K
/
L
] to select “ON”, then press
[OK].
e.g.) “Disc Full”
Disc Full
ON
OFF
Your setting will be activated.
6 Press [SETUP] to exit.
54 EN
E9M81UD_ZV457MG9.indd 54 2008/05/15 14:31:26
INFORMATION ON PLAYBACK
Before you play back DVD, read the following information.
Playable Discs and Files
This unit is compatible to play back the following discs.
To play back a DVD, make sure that it meets the requirements for region codes and color systems as described below. You can play back discs that have the following logos will play back on the unit. Other disc types are not guaranteed to play back.
DVD-video
DVD+RW
Playable discs Logos
Unplayable Discs
The following discs will not play back on this unit.
• CD-ROM
• DVD-RAM
• DVD-ROM
• Compact Disc-Interactive (CD-I)
• Video Single Disc (VSD)
• DVD-audio
• Unfinalized disc
• DVD contains MP3 and DVD or CD contains Windows
Media™ Audio / JPEG / DivX® files
• DVD-R or DVD-RW recorded in VR mode or non compatible recording format
• Blu-ray Disc
• Super Video CD
• HD DVD
On the following disc, the sound may not be heard.
• Super audio CD - Only the sound on the CD layer can be heard. The sound on the high-density super audio CD layer cannot be heard.
DVD+R
DVD-RW
(Finalized video mode discs only)
DVD-R
(Finalized video mode discs only)
Color Systems
DVD is recorded in different color systems throughout the world. The most common color system is NTSC
(which is used primarily in the United States and Canada).
This unit uses NTSC, so DVD you play back must be recorded in the NTSC system. You cannot play back DVD recorded in other color systems.
CD-DA (audio CD) video CD
CD-RW
Region Codes
This unit has been designed to play back DVD with region 1. DVD must be labeled for ALL regions or for region 1 in order to play back on the unit. You cannot play back DVD that are labeled for other regions. Look for the symbols on the right on your DVD. If these region symbols do not appear on your DVD, you cannot play back the DVD in this unit.
The number inside the globe refers to region of the world.
A DVD labeled for a specific region can only play back on the unit with the same region code.
CD-R
Playable files Media
CD-DA
MP3
CD-RW/-R is a trademark of DVD Format/Logo Licensing Corporation.
EN 55
2008/05/15 14:31:27 E9M81UD_ZV457MG9.indd 55
INFORMATION ON PLAYBACK
PBC (playback control) for Video CD
You can select images or information on the menu screen by activating the PBC (playback control) function of the video CD.
This unit conforms to ver.1.1 and ver. 2.0 of video CD standard with PBC function.
Ver.1.1 (without PBC function): You can enjoy playback picture as well as music CD.
Ver.2.0 (with PBC function): While using a video CD with
PBC function, “PBC” appears on the TV screen.
Hint for DVD Playback
The contents of DVD are generally divided into titles.
Titles may be further subdivided into chapters.
DVD-video title 1 title 2 chapter 1 chapter 2 chapter 1 chapter 2 chapter 3 track 1 track 2 audio CD, video CD track 3 track 4 track 5
Note
• PBC setting turns to “ON” when loading video CD with PBC function, thus, even after setting PBC to
“OFF” and ejecting the video CD then reloading the video CD, this setting turns to “ON” automatically.
• Some operations cannot be performed while PBC function is on. Cancel PBC function temporarily to perform those operations by following the instruction below.
1) Press [SETUP].
2) Use [
K
/
L
] to select “CD Playback Mode”, then press [OK].
“CD Playback Mode” menu will appear.
3) Use [
K
/
L
] to select “PBC (Video CD only)”, then press [OK].
4) Use [
K
/
L
] to select “ON” or “OFF”, then press [OK].
Your setting will be activated.
You can play back interactive software using menu screens. Refer to instructions in the video CD.
file 1 folder 1 file 2
MP3 file 3 folder 2 file 4 file 5
56 EN
E9M81UD_ZV457MG9.indd 56 2008/05/15 14:31:28
Direct Playback
BASIC PLAYBACK
1
Press [DVD] first.
Insert a playable disc (refer to page
25 on how to insert a disc).
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU SETUP o s
TITLE
OK p
B
RETURN j
F
-h g
CHANNEL
+
REC MODE VCR TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
Align the disc to the disc tray guide.
* Make sure the disc is compatible with this unit.
(Refer to page 55 for the list of compatible discs.)
It may take a while to load the disc.
2 Press [PLAY ] to start playback.
If you are playing back a DVD-video or video CD with PBC function, a menu may appear.
Refer to “Using the Title / Disc Menu” on page
60.
3 Press [STOP
C
] once to stop playback temporarily.
• Refer to “Resume Playback” on page 61.
Note
• Some discs may start playback automatically.
• You can select images or information on the menu screen by activating PBC (playback control) function
(page 56).
E9M81UD_ZV457MG9.indd 57
EN 57
2008/05/15 14:31:28
Playback from the Title List
BASIC PLAYBACK
If you want to see disc information, press [
{
] when the first page of the title list is displayed or press [
K
] when the first title is selected but not when “Play”, “Edit” or
“Overwrite” is highlighted.
e.g.) DVD+RW
.
DISC MENU
CLEAR
SETUP
No Disc Name
Disc DVD+RW
Total Titles
Disc Space Used
3
0:30:48
Disc Protect
Make Edits Compatible
OFF
Needed
RETURN e.g.) DVD+R j
F
-h g
CHANNEL
+
REC MODE VCR TIMER
No Disc Name
Disc DVD+R
Total Titles 5
Disc Space Used
Disc Protect
1:30:48
OFF
Finalize Finalized
1
Press [DVD] first.
Insert a playable disc (refer to page
25 on how to insert a disc).
* Make sure the disc is compatible with this unit.
(Refer to page 55 for the list of compatible discs.)
It may take a while to load the disc.
• Title list will appear automatically.
• To exit the title list, press [STOP
C
] .
• To resume the title list, press [TITLE] .
2 Use [
K
/
L
] to select a desired title, then press [OK].
1 SP (2Hr)
NOV/21/08 11:00AM CH12 SP
NOV/21/08 0:20:44
2
NOV/22/08 11:35AM CH13 EP
NOV/22/08 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
• For Video CD, when “PBC (Video CD only)” in
“CD playback Mode” menu is set to “ON”, the video CD main menu will appear when inserting a disc. In such case, select a numbered menu with [the Number buttons] .
• Press [
B
] to display the next page, and press
[
{
] to display the previous page.
1. Disc name
(Default “No Disc Name”)
2. Disc type
(DVD+RW/DVD+R/ DVD-RW/DVD-R)
3. Total number of title
(include “EMPTY TITLE”)
4. Total time of recorded disc space
5. Status of disc protection
(“ON” is protected disc.)
6. Making edits compatible/finalize
• When DVD+RW is inserted:
If the disc needs to be set “Make Edits Compatible”,
“Needed” is displayed. Otherwise, “Not Needed” is displayed. (Refer to page 80.)
• When DVD+R, DVD-RW or DVD-R is inserted:
If “Finalize” is done, “Finalized” is displayed.
Otherwise, “Unfinalized” is displayed.
3 Use [
K
/
L
] to select “Play”, then press [OK].
P l a y
1 SP (2Hr)
E d i t
O v e r w r i t e
NOV/21/08 11:00AM CH12 SP
NOV/21/08 0:20:44
2
NOV/22/08 11:35AM CH13 EP
NOV/22/08 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
Playback will start.
Note
• Some discs may start playback automatically.
• You can also start playback by pressing [PLAY
B
] instead of [OK] at step 2.
4 Press [STOP
C
] once to stop playback temporarily.
• Refer to “Resume Playback” on page 61.
5 8 EN
E9M81UD_ZV457MG9.indd 58 2008/05/15 14:31:29
BASIC PLAYBACK
Playing Back an Audio CD and a CD-RW / -R with MP3 Files
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.
STANDBY-ON
CLEAR
SETUP
1
Press [DVD] first.
Insert a playable disc (refer to page
25 on how to insert a disc).
* Make sure the disc is compatible with this unit.
(Refer to page 55 for the list of compatible discs.)
It may take a while to load the disc.
When an audio CD is inserted, track list will appear.
When a CD-RW/-R with MP3 files is inserted, file list will appear.
• To exit the track/file list, press [STOP
C
] .
• To resume the track/file list, press [TITLE] .
2 Use [
K
/
L
] to select a desired folder or track / file, then press [OK].
e.g.) File list
File List
DISC NAME
A
B j
-h g
CHANNEL
+
REC MODE VCR TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
Note
• The audio source of MP3 files cannot be recorded as digital sound by an MD or DAT deck.
• Files whose extension is other than “.mp3(MP3)” will not be listed.
• Some unplayable folders or files may be listed due to the recording status.
1/ 2
When selecting track / file:
Playback will start.
When selecting the folder (Not available for audio CD):
The files in the folder will appear.
Use [
K
/
L
] to select the file or folder you want to play back, then press [OK] .
• Press [PLAY
B
] , [OK] or [
B
] to move to any lower hierarchies.
• Press [ s
] or [RETURN] to move back to the previous hierarchy.
Hints for audio CD tracks and MP3 files:
• Folders are shown by .
• Audio CD tracks are shown by .
• MP3 files are shown by 3 .
• The system can recognize up to 255 folders, up to 99 tracks/999 files.
• Letters of a file/folder name overflowing the given space will be displayed as “...”. Unrecognizable characters will be replaced with asterisks.
• If there are no files in the folder, “No Files” will be displayed.
It is recommended that files to be played back in this unit are recorded under the following specifications:
<MP3>
• Sampling frequency
• Constant bit rate
: 44.1 kHz or 48 kHz.
: 112 kbps - 320 kbps
EN 5 9
E9M81UD_ZV457MG9.indd 59 2008/05/15 14:31:31
BASIC PLAYBACK
Using the Title / Disc Menu
DVD or video CD with PBC function may contain a title list, which describes the contents of the disc, or a disc menu, which guides you through the available functions in the disc.
Press [DVD] first.
1) Insert a playable disc (refer to page 25 on how to insert a disc).
* Make sure the disc is compatible with this unit. (Refer to page 55 for the list of compatible discs.)
It may take a while to load the disc.
Pause
1) During playback, press [PAUSE
F
].
Playback will be paused and sound will be muted.
F
2) Press [PLAY
B
] to return to the normal playback.
2) Press [TITLE] or [DISC MENU] to call up the title list or disc menu.
3) Use [
K
/
L
/
{
/
B
] to make a selection, and then press [OK] to enable your selection.
4) Press [STOP
C
] to exit.
Note
• On DVD, set “Still Mode” to “Field” in “Playback” menu if pictures in the pause mode are blurred.
(Refer to page 86.)
Note
• You can select a numbered menu with [the Number buttons] also.
• Menus vary among discs. Refer to the information accompanying the disc for details.
• [TITLE] or [DISC MENU] will not always be active with all DVD.
• For video CD, when “PBC (Video CD only)” in “CD
Playback Mode” menu is “ON”, the video CD main menu will appear when inserting a disc.
60 EN
E9M81UD_ZV457MG9.indd 60 2008/05/15 14:31:34
Resume Playback
SPECIAL PLAYBACK
Skipping TV Commercials During
Playback
You can play back from where you stopped playing back the disc last.
1) During playback, press [STOP
C
].
The resume message will appear.
You can skip TV commercials to enjoy the recorded programs without interrupting.
Resume ON
During playback, press [CM SKIP].
Normal playback will start at 30 seconds ahead from the point you press [CM SKIP] .
Every time you press [CM SKIP] , the searching point will be extended by 30 seconds ahead.
You can press [CM SKIP] up to 6 times (180 seconds).
2) Press [PLAY
B
].
In a few seconds, playback will resume from the point at which it stopped last. You can resume playback at the same point even if you turn off the unit.
To cancel the resume playback and start playing back the disc from the beginning, press [STOP
C
] again while the playback is stopped.
Note
• For MP3 files, playback will resume from the beginning of the file at which playback was stopped.
• Some video CD with the PBC function resume playback from the beginning of the track.
e.g.) Press [CM SKIP] once.
CM Skip 30 sec.
(forwarding 30 seconds)
B
Playback will return to the normal playback.
Fast Forward / Fast Reverse Playback
Rapid Playback
1) During playback, press [
D
] or [
E
].
Every time you press [
D
] or [
E
] , approximate speed will be changed as follows.
Fast forward or fast reverse playback across titles (for
DVD) or files (for MP3 files) is not possible.
Rapid playback function is available only during playback.
This function is available only on discs recorded in the
Dolby Digital format, and plays back in a slightly faster/ slower speed while keeping the sound quality just as normal playback.
g
4 0x h g
2 0x h
5x g h normal speed playback g h g
2 x 2 0x h g
4 0x h
For video CD, approximate forward/reverse speeds are
2x, 8x, 16x.
For audio CD, MP3 files, approximate speed is fixed at
8x with sound (indicated with / ).
2) Press [PLAY
B
] to return to the normal playback.
Note
• Forward/reverse speed will be indicated with icons as follows.
forward (approx. speed)
2x:
20x:
40x:
reverse (approx. speed)
5x:
20x:
40x:
1) During playback, press [RAPID PLAY].
B
:
B
:
B
:
Press [RAPID PLAY] once during playback.
Plays back approximately at 0.8 times of normal playback.
Press [RAPID PLAY] twice during playback.
Plays back approximately at 1.3 times of normal playback.
Press [RAPID PLAY] 3 times to play back in normal speed.
No effects.
2) Press [PLAY
B
] to return to the normal playback.
Note
• Audio (language) setting cannot be changed while using this mode.
• This feature may not work at some point in a disc.
• Audio is PCM during rapid playback mode except when using digital audio connection.
• When using digital audio connection (COAXIAL), the
LPCM sound (2 channel) will be output.
EN 61
E9M81UD_ZV457MG9.indd 61 2008/05/15 14:31:34
SPECIAL PLAYBACK
Step by Step Playback
1) During playback, press [PAUSE
F
].
Playback will be paused and sound will be muted.
2) Press [
G
] repeatedly.
Playback will advance one frame (or step) at a time when you press [
G
] with the sound muted.
To play back step by step backward:
Press [
H
] repeatedly.
Every time you press the button, the playback will go backward by one frame.
• Press and hold [
H
] / [
G
] to reverse/ advance continuously.
3) Press [PLAY
B
] to return to the normal playback.
Zoom
1) During playback, press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK] within 1 second or wait for 1 second to display the selection menu.
e.g.) DVD-video
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
Note
• Only step by step forward playback is available for playing back video CD.
3) Use [
K
/
L
] to select a desired zoom factor to zoom, then press [OK].
1/ 5 1/ 5
× 1.2
× 1.5
× 2.0
0:01:00 / 1:23:45
DVD Video
Slow Forward / Slow Reverse Playback
1) During playback, press [PAUSE
F
[
D
] or [
E
].
]. Then press
Every time you press [
D
] or [
E
] , approximate speed will be changed as follows. (The sound will remain muted.)
1/4 x g h
1/8 x g g h
1/1 6x h pause g h g
1/1 6x h
1/8 x g h
1/3 x
2) Press [PLAY
B
] to return to the normal playback.
Note
• Forward/reverse speed will be indicated with icons as follows.
forward (approx. speed)
1/16x:
1/8x:
1/3x:
reverse (approx. speed)
1/16x:
1/8x:
1/4x:
• Only slow forward is available when playing back video CD.
Zoom menu will appear.
There are four options
(x1.0, x1.2, x1.5 and x2.0), these are displayed excluding the current zoom rate.
Zoom area will be displayed.
4) Use [
K
/
L
/
{
/
B
] to select a desired zoom position, then press [OK].
Zoom playback will start.
Note
• When selecting a smaller factor than the current one, the zoom area will not be displayed.
• To exit the zoom menu, press [DISPLAY] again at step 1.
• To cancel the zoom function, select “x1.0” using
[
K
/
L
] , then press [OK] .
62 EN
E9M81UD_ZV457MG9.indd 62 2008/05/15 14:31:37
SPECIAL PLAYBACK
Marker Setting Repeat Playback
This feature allows you to assign a specific point on a disc to be called back later.
Available repeat function may vary depending the discs.
1) During playback press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK] within 1 second or wait for 1 second to display the selection menu.
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
1) During playback, press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK] within 1 second or wait for 1 second to display the marker list.
e.g.) DVD-video
3) Use [
K
/
L
] to select a desired marker number.
When it reaches the desired point, press [OK].
The title (track) number and the time will be displayed.
4) To return to the marker later:
Use [ then press [OK].
Note
K
/
L
1/ 5
1/ 5
1/ 5
1/ 5
3
4
1
2
5
6
---
---
---
---
---
---
0:01:00 / 1:23:45
DVD Video
0:01:00 / 1:23:45
DVD Video
] to select the desired marker number,
• To clear a marker, select the marker number to be cleared, then press [CLEAR] .
• All markers will be erased when you operate these operations listed below.
– Opening the disc tray
– Turning off the power
– Record on a recordable disc
• You can mark up to 6 points.
• Marker setting is not available when you play back the video CD with PBC function.
3) Use [
K
/
L
] to select a desired repeat type, then press [OK].
e.g.) DVD-video
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
OFF
Title
Chapter
A – B e.g.) audio CD, video CD
1/ 5 0:00:15 / 0:05:00
CD
OFF
Track
All
A – B e.g.) MP3 files
1/ 5 0:00:15
MP3
OFF
Track
All
Group
The selected repeat playback will start.
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD
Repeat
Title
Title:
The current title will be played back repeatedly.
Chapter:
The current chapter will be played back repeatedly.
All:
The current disc will be played back repeatedly.
A-B:
Desired section can be played back repeatedly.
1) Use [
K
/
L
] to select “A-B”, then press [OK] .
2) Press [OK] at the desired starting point A.
3) Press [OK] at the desired ending point B.
Track:
The current track or file will be played back repeatedly.
Group:
The current folder will be played back repeatedly.
Note
• Point B for the repeat A-B playback should be set within the same title or track as point A.
• To cancel the repeat playback, select “OFF” at step 3.
The repeat setting will also be canceled when you stop playback.
• You cannot select “Group” during the random playback.
• Repeat playback is not available when you play back the video CD with PBC function.
• During the A-B repeat, if you reaches the point A with any reverse playback, the reverse playback will be canceled and the A-B repeat playback resumes from point A.
EN 63
E9M81UD_ZV457MG9.indd 63 2008/05/15 14:31:40
SPECIAL PLAYBACK
Random Playback Program Playback
You can play back a disc randomly instead of playing back in the original order.
1) Press [SETUP].
2) Use [
K
/
L
] to select “CD Playback Mode”, then press
[OK].
“CD Playback Mode” menu will appear.
3) Use [
K
/
L
] to select “Random Play”, then press
[OK].
Random playback will start.
You can program the disc to play back in your desired order.
1) Press [SETUP].
2) Use [
K
/
L
] to select “CD Playback Mode”, then press
[OK].
“CD Playback Mode” menu will appear.
3) Use [
K
/
L
] to select “Program Play”, then press
[OK].
Note
• To cancel random playback, press [STOP
C
] twice during random playback. “OFF” appears on the TV screen.
• For video CD with PBC function, the PBC setting will be switched to off automatically when you start random playback.
4) Use [
K
/
L
] to select a desired track, then press [OK] or [
B
].
CD Playback Mode
Program Play
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Total 0:00:00
Repeat this step until you program all the desired tracks.
5) Press [PLAY
B
].
CD Playback Mode
Program Play
09 04 10 06 --
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Total 0:31:07
Program playback will start.
Note
• To erase tracks you selected, press [CLEAR] at step 4.
• You can make program settings up to 50 tracks.
• To cancel program playback, press [STOP
C
] twice during program playback. “OFF” appears on the TV screen.
• You may also select a desired track using [the
Number buttons] at step 4.
• For video CD with PBC function, the PBC setting will be switched to off automatically when you start program playback.
64 EN
E9M81UD_ZV457MG9.indd 64 2008/05/15 14:31:41
SEARCH
Track Search Title / Chapter Search
Using [
H
] / [
G
]
1) During playback, press [
G
] to skip the current title or chapter and move to the next.
The title or chapter will move forward by one at a time.
• If there is no chapter in one title, the current title will be skipped.
To go back to the beginning of the current title or chapter, press [
H
] .
Press it repeatedly to go to the previous title or chapter. The title or chapter will move backward one at a time.
Using [
H
] / [
G
]
1) During playback, press [
G
] to skip the current track / file and move to the next.
The track/file will move forward one at a time.
To go back to the beginning of the current track/file, press [
H
] .
Press it repeatedly to go to the previous track/file. The track/file will move backward one at a time.
Using [DISPLAY]
1) During playback, press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK].
e.g.) DVD-video
Using [DISPLAY]
1) During playback, press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK].
e.g.) audio CD
1/ 5 0:00:15 / 0:05:00
CD
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video e.g.) MP3 files
1/ 5 0:00:15
MP3
The number next to will be highlighted.
3) Title:
Use [
K
/
L
] or [the Number buttons] to enter a desired title number to search, then press [OK].
Title search will start.
Chapter:
Press [
B
] to move to the number next to for chapter.
Use [
K
/
L
] or [the Number buttons] to enter a desired chapter number to search, then press [OK].
After the search, playback will start automatically.
Note
• In search mode display, total numbers of each search contents (title/chapter/time) are shown as a denominator.
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
The number next to will be highlighted.
3) Use [
K
/
L
] or [the Number buttons] to enter a desired track / file number to search, then press
[OK].
After the search, playback will start automatically.
Note
• During CD playback you can enter a track number directly using [the Number buttons] for track search without displaying the menu.
• Track search is not available when you play back the video CD with PBC function.
total number of titles total number of chapters total time of the title
EN 65
2008/05/15 14:31:42 E9M81UD_ZV457MG9.indd 65
Time Search
1) During playback, press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK].
e.g.) DVD-video
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
SEARCH e.g.) audio CD
1/ 5 0:00:15 / 0:05:00
CD
The number next to will be highlighted.
To move to the number next to , press [
B
] .
When time search is not available, and time counter are not displayed.
3) Use [
K
/
L
/
{
/
B
] or [the Number buttons] to enter a desired time to search, then press [OK].
After the search, playback will start automatically.
Note
• Time search is available only in the same track, file or title.
• Time search is not available when you play back the video CD with PBC function.
66 EN
E9M81UD_ZV457MG9.indd 66 2008/05/15 14:31:44
SELECTING THE FORMAT OF AUDIO AND VIDEO
You can select the format of audio and video as you prefer depending on the contents of the disc you are playing back.
Switching Subtitles
DVD-video may have subtitles in 1 or more languages.
Available subtitle languages can be found on the disc case. You can switch subtitle languages anytime during playback.
Switching Audio Soundtrack
When playing back a DVD-video recorded with 2 or more soundtracks (these are often in different languages), you can switch them during playback.
When playing back video CD, audio CD you can switch
“L/R”(stereo), “L”(left) or “R”(right).
1) During playback, press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK] within 1 second or wait for 1 second to display the selection menu.
e.g.) DVD-video
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
3) Use [
K
/
L
] to select a desired subtitle language, then press [OK].
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
OFF
1.English
1) During playback press [DISPLAY], then proceed to step 2), or press [AUDIO] then proceed to step 3).
2) Use [
{
/
B
] to select , then press [OK] within 1 second or wait for 1 second to display the selection menu.
3) Use [
K
/
L
] to select a desired audio soundtrack or audio channel, then press [OK].
For DVD-video
• Audio soundtrack will switch.
1/ 5 1/ 5
1.Dolby Digital 5.1ch English
2.Dolby Digital 2ch English
0:01:00 / 1:23:45
DVD Video
Subtitle will be displayed in the selected language.
When selecting “OFF”, subtitle will disappear.
Note
• Some discs will only allow you to change the subtitle from the disc menu. Press [TITLE] or [DISC MENU] to display the disc menu.
• If a 4-digit language code appears in the subtitle menu, refer to the “LANGUAGE CODE” on page 100.
• If the title contains both main and sub audio, you can further select “L” (main), “R” (sub), or “L/R” (mixed of main and sub).
For audio CD, video CD
• Audio channel will switch.
e.g.) audio CD
1/ 5 0:00:15 / 0:05:00
CD
1. L/R
2. L
3. R
Note
• Some discs will only allow you to change the soundtrack from the disc menu. Press [TITLE] or
[DISC MENU] to display the disc menu.
EN 67
2008/05/15 14:31:45 E9M81UD_ZV457MG9.indd 67
SELECTING THE FORMAT OF AUDIO AND VIDEO
Switching Virtual Surround System Switching Camera Angles
You can enjoy stereophonic virtual space through your existing 2 channel stereo system.
1) During playback, press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK] within 1 second or wait for 1 second to display the selection menu.
e.g.) DVD-video
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
Some DVD-video have scenes shot from 2 or more angles. Angle information should be on the disc case if the disc contains multi-angle scenes.
1) During playback, press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK].
e.g.) DVD-video
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
3) Use [
K
/
L
] to select “OFF”, “Type 1” or “Type 2”, then press [OK].
e.g.) DVD-video
1/ 5 1/ 5
OFF
Type 1
Type 2
0:01:00 / 1:23:45
DVD Video
OFF : no effect
Type 1 : natural effect
Type 2 : emphasized effect
Note
• Select “OFF” in a case sound is distorted.
• The setting will be kept even when the unit is turned off.
Angle icon appears when a switching camera angle is available.
Angle will switch each time you press [OK].
Note
• Angle icon does not appear on the TV screen in a case you set “Angle Icon” to “OFF” in “Playback” menu. Refer to page 86.
Reducing Block Noise
This function reduces noise in the playback picture.
1) During playback, press [DISPLAY].
2) Use [
{
/
B
] to select , then press [OK] within 1 second or wait for 1 second to display the selection menu.
e.g.) DVD-video
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
3) Use [
K
/
L
] to select a desired option, then press
[OK].
1/ 5 1/ 5 0:01:00 / 1:23:45
DVD Video
OFF
Type 1
Type 2
Your setting will be activated.
OFF : When playing back titles with a few noises such as DVD-video.
Type 1 : For the titles recorded in long time mode such as EP or SLP mode.
Type 2 : Same as type 1, only more effective.
6 8 EN
E9M81UD_ZV457MG9.indd 68 2008/05/15 14:31:46
INFORMATION ON DISC EDITING
Guide to a Title List Editing Discs
Title list allows you to check the titles recorded on the disc easily. You can choose a title to play back from this list and easily edit the titles as you prefer.
Press [DVD], then press [TITLE].
1 2 3 4
6
P l a y
E d i t
O v e r w r i t e
1 SP (2Hr)
NOV/21/08 11:00AM CH12 SP
NOV/21/08 0:20:44
2
NOV/22/08 11:35AM CH13 EP
NOV/22/08 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
Edit
2
5
2
Title Delete
Edit Title Name
Chapter Mark
Hide Chapter
Index Picture
Title Dividing
NOV/22/08 11:35AM CH13 EP
1 : 05 : 00
11 1
0
9 8
7
1. Title list: List of the titles recorded on the disc, and their information.
2. Arrow: Indicating there is a previous / next page.
3. Title information: On the first line, title name
(editable) is displayed. On the second line, the length of the title is displayed.
Empty title: The portion of the disc where there is no recordings are made. As for the empty title, available recording time by the selected recording mode is displayed on the second line.
4. Recording mode: Currently selected recording mode is displayed here.
5. Capacity indicator: Indicating the position and the amount of each title in the disc. The portion for the selected title is highlighted.
6. Thumbnails: A cut from the recorded content is displayed here.
7. Submenu: Submenus for the selected menu are displayed here.
8 . Title name (editable) : If you do not name the title, the recorded date, time, channel, and the recording mode are displayed here.
9 . Progress bar: Indicating the progress of the playback.
10. Preview window: Preview of the selected title is displayed here.
11. Playback status: Indicating the current playback status of the selected title.
Press [STOP
C
] to exit the title list.
You can edit discs for the following items. Be sure that once you edit titles, they will not remain as original.
• Deleting Titles (Refer to page 70.)
• Putting Names on Titles (Refer to page 71.)
• Setting Chapter Marks (Refer to page 72.)
• Clearing Chapter Marks (Refer to pages 73-74.)
• Hiding Chapters (Refer to page 75.)
• Setting Pictures for Thumbnails (Refer to page 76.)
• Dividing a Title (DVD+RW/DVD-RW only)
(Refer to page 77.)
• Putting Name on Disc (Refer to page 78.)
• Erasing Disc (Refer to page 79.)
• Making Edits Compatible (Refer to page 80.)
Note
• When selecting “Edit” on pop-up menu of the title list and edit the title, the title list is displayed after writing the edited contents onto the disc.
• The capacity indicator in the right side of the title list may not indicate the precise capacity in the disc.
• The capacity indicator may not indicate the capacity for the titles of which recording time is short.
• Once you have finalized a DVD+R/ DVD-R, you cannot edit or record anything on that disc.
EN 6 9
2008/05/15 14:31:48 E9M81UD_ZV457MG9.indd 69
EDITING DISCS
Deleting Titles
You can delete titles which you do not need anymore.
Please be advised that the titles once deleted cannot be brought back to the disc.
For DVD+RW/DVD-RW, when the last recorded title in the title list is deleted, the available disc space to record on will be increased. For DVD+R/DVD-R, the disc space to record on will not be changed.
3 Use [
K
/
L
] to select “Edit”, then press [OK].
P l a y
E d i t
O v e r w r i t e
1 SP (2Hr)
NOV/21/08 11:00AM CH12 SP
NOV/21/08 0:20:44
2
NOV/22/08 11:35AM CH13 EP
NOV/22/08 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
4
PQRS
7
.
DISC MENU
5
TUV
8
SPACE
0
6
WXYZ
9
CLEAR s j B
SETUP
B
RETURN
4 Use [
K
/
L
] to select “Title Delete”, then press [OK].
Edit
1 Title Delete
Edit Title Name
Chapter Mark
Hide Chapter
Index Picture
Title Dividing
F
-h g
CHANNEL
+
C
REC MODE VCR TIMER
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
5 Use [
K
/
L
] to select “Yes”, then press
[OK].
Edit - Title Delete
Yes
1
No
Press [DVD] first.
1 Press [TITLE].
Use [
K
/
L
] to select a desired title, 2 then press [OK].
1 SP (2Hr)
NOV/21/08 11:00AM CH12 SP
NOV/21/08 0:20:44
2
NOV/22/08 11:35AM CH13 EP
NOV/22/08 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
Note
• Deleted part of the titles in the capacity indicator changes in color.
• As for DVD+RW/DVD-RW if you delete the title, deleted title will be displayed as “EMPTY TITLE”.
70 EN
E9M81UD_ZV457MG9.indd 70
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
After that, “Are you sure?” will appear, select
“Yes” and then press [OK] .
Title will be deleted.
Data will be written onto the disc momentarily.
e.g.) DVD+R/DVD-RW/-R
Please finalize the disc when the writing is completed before playing back on other DVD players.
Writing to Disc 90%
This operation may take a while to be completed.
After editing is complete, the title list will appear.
e.g.) DVD+RW/DVD-RW
1
EMPTY TITLE
0:21:14 SP(2Hr)
2
SP (2Hr)
NOV/22/08 11:35AM CH13 EP
NOV/22/08 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
2008/05/15 14:31:49
EDITING DISCS
Putting Names on Titles
You can put title names on the titles and change the names from this menu.
STANDBY-ON
4 Use [
K
/
L
] to select “Yes”, then press
[OK].
Edit - Edit Title Name
Yes
1
No
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
MY FAVORITE
1 : 05 : 00
The name you entered will be activated for the title.
.
DISC MENU
TITLE
SETUP
5 After this operation is completed, press [RETURN] to exit.
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
1 menu.
Edit j B
F
-h g
CHANNEL
+
C
Follow steps 1 to 3 in “Deleting
Titles” on page 70 to display “Edit”
2 Use [
K
/
L
] to select “Edit Title
Name”, then press [OK].
1
NOV/21/08 11:00AM CH12 SP
Title Delete
Edit Title Name
Chapter Mark
Hide Chapter
Index Picture
Title Dividing
1 : 05 : 00
3 To enter a title name, follow the steps of “Guide to Edit Title Name” on this page.
Edit - Edit Title Name
1
A B C a b c
1 2 3
@ !
?
character set
M
1 : 05 : 00 area for entering title names
When you finish entering a title name, press [OK] .
7
8
5
6
9
2
3
4
Guide to Edit Title Name
1) Use [
K
/
L
] to select a desired character set, then press [OK].
2) Follow the list below, use [the Number buttons] repeatedly until the desired letter appears.
Select
Press
0
ABC abc
<space> <space>
123
0
@ !
?
<space>
1 (*1) (*1) 1
! ” # $ % & ’ ( )
* + , - . / : ; < = >
? @ [ ] ^ _ { | }
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ abc def ghi jkl mno pqrs tuv wxyz
8
9
6
7
4
5
2
3
(*2)
(*2)
(*2)
(*2)
(*2)
(*2)
(*2)
(*2)
*1 Press 1 , character set will be changed to the “ @!? ” mode automatically.
*2 Press
2
to
9
, character set will be changed to the previous input mode automatically.
• To delete letters, press [CLEAR] repeatedly.
Holding [CLEAR] to delete all letters.
• Use [ s
/
B
] to move the cursor to the left and right.
• You can enter up to 30 letters.
Note
• Undefined letters in a title name are shown by “*”. If you delete them, adjoining letters may change to “*” or other.
EN 71
E9M81UD_ZV457MG9.indd 71 2008/05/15 14:31:50
EDITING DISCS
Setting Chapter Marks
You can put chapter marks in each title. Once a chapter is marked, you can use it for the chapter search feature.
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU SETUP
1 Follow steps 1 to 3 in “Deleting
Titles” on page 70 to display “Edit” menu.
2 Use [
K
/
L
] to select “Chapter Mark”, then press [OK].
Submenu will appear.
3 Press [PLAY ] and then [PAUSE
F
] to decide the point at which you will create a new chapter mark.
• It is convenient to use [
H
] , [
G
] ,
[
E
] and [
D
] for finding the point to add a new chapter mark.
s
TITLE
B
4 Use [
K
/
L
] to select “Add”, then press
[OK].
Edit - Chapter Mark
Add
Delete
Delete All
1
Chapter 2/ 2
C
--
CHANNEL
+
REC MODE VCR DVD TIMER
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
5 Use [
K
/
L
] to select “Yes”, then press
[OK].
Edit - Chapter Mark - Add
Yes 1
No
Chapter 2/ 2
F
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
A new chapter mark will be added.
6 Press [RETURN] twice to exit.
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
Note
• When the number of chapter marks in a title is 99 and the number of chapter marks in a disc is 254, chapter marks cannot be added.
• Besides the above-mentioned, it is not likely to be able to add according to recorded time and number of chapters.
• Remaining time of the disc may decrease when adding chapter marks or increase when clearing chapter marks depending on the recording time or edited contents.
72 EN
E9M81UD_ZV457MG9.indd 72 2008/05/15 14:31:51
Clearing Chapter Marks
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU SETUP s
TITLE
B
B
F
-h g
CHANNEL
+
C
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
EDITING DISCS
1 Follow steps 1 to 3 in “Deleting
Titles” on page 70 to display “Edit” menu.
2 Use [
K
/
L
] to select “Chapter Mark”, then press [OK].
Submenu will appear.
3 Use [
H
] / [
G
] to select a chapter mark to be deleted.
4 Use [
K
/
L
] to select “Delete”, then press [OK].
5 Use [
K
/
L
] to select “Yes”, then press
[OK].
Edit - Chapter Mark - Delete
Yes
1
No
Chapter 2/ 2
F
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
The selected chapter mark will be deleted.
6 Press [RETURN] twice to exit.
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
Note
• Remaining time of the disc may decrease when adding chapter marks or increase when clearing chapter marks depending on the recording time or edited contents.
• You cannot delete the chapter mark 1.
E9M81UD_ZV457MG9.indd 73
EN 73
2008/05/15 14:31:53
EDITING DISCS
Clearing Chapter Marks (cont’d)
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
TUV
8
SPACE
0
ABC
2
JKL
5
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU SETUP s
TITLE
B j B
F
-h g
CHANNEL
+
C
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
To delete all chapter marks:
1 Follow steps 1 to 3 in “Deleting
Titles” on page 70 to display “Edit” menu.
2 Use [
K
/
L
] to select “Chapter Mark”, then press [OK].
Submenu will appear.
3 Use [
K
/
L
] to select “Delete All”, then press [OK].
4 Use [
K
/
L
] to select “Yes”, then press
[OK].
Edit - Chapter Mark - Delete All
Yes
1
No
Chapter 2/ 2
F
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
5 Use [
K
/
L
] to select “Yes”, then press
[OK].
Edit - Chapter Mark - Delete All
Are you sure?
Yes
No
1
Chapter 2/ 2
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
All chapter marks will be deleted.
6 Press [RETURN] twice to exit.
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
Note
• Remaining time of the disc may decrease when adding chapter marks or increase when clearing chapter marks depending on the recording time or edited contents.
74 EN
E9M81UD_ZV457MG9.indd 74 2008/05/15 14:31:53
EDITING DISCS
Hiding Chapters
You can hide chapters from the title list.
Hidden chapters are skipped during playback.
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU SETUP s
TITLE
STANDBY-ON
B
1 Follow steps 1 to 3 in “Deleting
Titles” on page 70 to display “Edit” menu.
2 Use [
K
/
L
] to select “Hide Chapter”, then press [OK].
Submenu will appear.
3 Use [
H
] / [
G
] to decide the chapter to be hidden.
4 Use [
K
/
L
] to select “Hidden”, then press [OK].
Edit - Hide Chapter
Visible
Hidden
1
Chapter 2/ 2 Visible
B
F
-h g
CHANNEL
+
C
REC MODE VCR DVD TIMER
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
5 After this operation is completed, press [RETURN] twice to exit.
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
SEARCH
If you want hidden chapters to be “Visible”, select the chapter to be shown. Then use
[
K
/
L
] to select “Visible” at the step 4 on this page.
Data will be written onto the disc momentarily.
After that, title list is displayed.
Note
• ”Hidden” will be displayed in the preview window while previewing the hidden chapter.
• When you make all chapters in the title “Hidden”,
“Hidden” is displayed in a thumbnail of the title list.
Hidden
1 SP (2Hr)
NOV/21/08 11:00AM CH12 SP
NOV/21/08 0:20:44
2
NOV/22/08 11:35AM CH13 EP
NOV/22/08 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
EN 75
2008/05/15 14:31:54 E9M81UD_ZV457MG9.indd 75
EDITING DISCS
Setting Pictures for Thumbnails
You can set your desired scene as a thumbnail for each title.
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU SETUP s
TITLE
STANDBY-ON
B
1 Follow steps 1 to 3 in “Deleting
Titles” on page 70 to display “Edit” menu.
2 Use [
H
], [
G
], [
E
], [
D
], [PAUSE
F
] and [PLAY
B
] to decide the picture you want to select as a thumbnail.
3 Use [
K
/
L
] to select “Index Picture”, then press [OK].
4 Use [
K
/
L
] to select “Yes”, then press
[OK].
Edit - Index Picture
1
Yes
No
C
CHANNEL
--
REC MODE VCR
+
DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
F
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
A picture for thumbnail will be set.
5 Press [RETURN] to exit.
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
Note
• If the selected picture for a thumbnail is overwritten, the index picture is reset to the first scene of the title.
76 EN
E9M81UD_ZV457MG9.indd 76 2008/05/15 14:31:55
Dividing a Title
You can divide one title into 2 new titles.
EDITING DISCS
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU SETUP s
TITLE
B
RETURN
1 Follow steps 1 to 3 in “Deleting
Titles” on page 70 to display “Edit” menu.
2 Use [
H
], [
G
], [
E
], [
D
], [PAUSE
F
] and [PLAY
B
] to decide the point at which you will divide the title.
3 Use [
K
/
L
] to select “Title Dividing”, then press [OK].
4 Use [
K
/
L
] to select “Yes”, then press
[OK].
Edit - Title Dividing
1
Yes
No
C
--
CHANNEL
+
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
F
NOV/21/08 11:00AM CH12 SP
1 : 05 : 00
The title will be divided into 2 new titles.
Both title names are identical, and index pictures are reset to the first scene at this point.
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
Note
• You cannot divide a title of the disc when the number of recording titles reaches the maximum of
49, and the number of recording chapters reaches the maximum of 254.
E9M81UD_ZV457MG9.indd 77
EN 77
2008/05/15 14:31:56
EDITING DISCS
Putting Name on Disc
You can put a name on the disc and change it from this menu.
Press [STOP
C
] if you are playing back a disc.
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU s
TITLE
B
RETURN j B
F
-h g
CHANNEL
+
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
1 Press [SETUP].
2 Use [
K
/
L
] to select “Disc Edit”, then press [OK].
3 Use [
K
/
L
] to select “Edit Disc
Name”, then press [OK].
e.g.) DVD+RW
Disc Edit
Edit Disc Name
Erase Disc
Make Edits Compatible
Disc Protect OFF ON
A window for entering a title name will appear.
Edit Disc Name
No Disc Name
Disc DVD+RW
Total Titles
Disc Space Used
Disc Protect
Make Edits Compatible
3
0:30:48
OFF
Needed
A B C a b c
1 2 3
@ !
?
4 To enter a disc name, follow the steps of “Guide to Edit Title Name” on page
71.
When you finish entering a title name, press
[OK] .
5 Use [
K
/
L
] to select “Yes”, then press
[OK].
Edit Disc Name
Yes
No
No Disc Name
Disc DVD+RW
Total Titles 3
Disc Space Used 0:30:48
Disc Protect
Make Edits Compatible
OFF
Needed
MY FAVORITE DISC
The name you entered will be activated for the title.
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
Note
• You cannot select “Disc Edit” when finalized DVD+R or DVD-R is inserted.
7 8 EN
E9M81UD_ZV457MG9.indd 78 2008/05/15 14:31:57
Erasing Disc
You can erase all titles on a disc.
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
DISC MENU
TUV
8
SPACE
0
ABC
2
JKL
5
DEF
3
MNO
6
WXYZ
9
CLEAR
SETUP s
TITLE
B
RETURN j B
F
-h g
CHANNEL
+
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
EDITING DISCS
Press [STOP
C
] if you are playing back a disc.
1 Follow steps 1 to 2 in “Putting Name on Disc” on page 7 8 to display “Disc
Edit” menu.
2 Use [
K
/
L
] to select “Erase Disc”, then press [OK].
e.g.) DVD+RW
Disc Edit
Edit Disc Name
Erase Disc
Make Edits Compatible
Disc Protect OFF ON
3 Use [
K
/
L
] to select “Yes”, then press
[OK].
When you press “Yes”, all the contents in the disc will be erased.
Are you sure to erase the disc?
Yes
No
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
Note
• When you select “Yes” at step 3, all contents of the disc will be erased.
E9M81UD_ZV457MG9.indd 79
EN 7 9
2008/05/15 14:31:58
EDITING DISCS
Making Edits Compatible
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
DISC MENU
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
SETUP
Press [STOP
C
] if you are playing back a disc.
If you have added or deleted chapters, or made chapters hidden, you must perform “Make Edits Compatible” to see those effects on other unit.
STANDBY-ON
1 Follow steps 1 to 2 in “Putting Name on Disc” on page 7 8 to display “Disc
Edit” menu.
2 Use [
K
/
L
] to select “Make Edits
Compatible”, then press [OK].
Disc Edit
Edit Disc Name
Erase Disc
Make Edits Compatible
Disc Protect OFF ON s
TITLE
B
RETURN j B
F
-h g
CHANNEL
+
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
3 Use [
K
/
L
] to select “Yes”, then press
[OK].
Activate the Make Edits Compatible?
Yes
No
Data will be written onto the disc momentarily.
This operation may take a while to be completed.
8 0 EN
E9M81UD_ZV457MG9.indd 80 2008/05/15 14:31:59
LIST OF SETTINGS
The following table is the contents which you can set and the default setting.
Refer to the following table for useful operation.
Setup
Playback
Pages 84-86
Display
Pages 87-89
Items (highlight is the default)
Parental Lock
Disc Audio
Audio Language
Subtitle Language
Angle Icon
Still Mode
OSD Language
Screen Saver
FL Dimmer
DTV CC
CC Style
pages 36-37
Dynamic Range
Control
PCM
Dolby Digital
Disc Menu Language
Caption Service
page 35
Recording
page 40
User Setting
Font Size
OFF
level 8 [Adult] to 1 [Kid Safe]
Contents
Set the parental level for DVD playback.
Compressing the range of sound volume.
ON
OFF
48kHz
96kHz
PCM
Stream
Set whether the sound recorded in 96kHz will be down sampled in 48kHz.
Set the type of sound signal which outputs from the digital audio output jack.
Set the language for disc menu language.
English
French
Spanish
Other
Set the language for audio.
Original
English
French
Spanish
Other
Set the language for subtitles.
OFF
English
French
Spanish
Other
ON
OFF
Set whether or not to display the angle icon.
Set the type of still image in pausing playback.
Auto
Field
Frame
Set the language for OSD (on-screen display).
English
Français
Español
OFF
5minutes
10minutes
15minutes
30minutes
Auto
Bright
Dark
Set the idling time before the screen saver starts.
Set the brightness of the front panel display.
Set the type of the DTV closed caption.
OFF
Service1
Service2
Service3
Service4
Service5
Service6
ON
OFF
Set whether to record the DTV closed caption or not.
ON
OFF
Large
Middle
Small
Set the CC style setting whether or not is effective.
Set font size of the displayed caption.
Font Style Set font style of the displayed caption.
Font Opacity
Style1
Style2
Style3
Style4
Style5
Style6
Style7
Style8
Solid
Transparent
Translucent
Flash
Set the font opacity of the displayed caption.
EN 8 1
E9M81UD_ZV457MG9.indd 81 2008/05/15 14:32:00
LIST OF SETTINGS
Setup
Display
Pages 87-89
Video
Page 90
Items (highlight is the default)
CC Style
pages 36-37
V-Chip
Font Color
White
Black
Red
Green
Blue
Yellow
Magenta
Cyan
Edge Type
Edge Color
None
Raised
Depressed
Uniform
L.Shadow
R.Shadow
White
Black
Red
Green
Blue
Yellow
Magenta
Cyan
Back Opacity
Back Color
Solid
Transparent
Translucent
Flash
White
Black
Red
Green
Blue
Yellow
Magenta
Cyan
MPAA Rating
TV Rating
Canadian French
Rating
18 ans+
16 ans+
13 ans+
8 ans+
G
E
Canadian
English Rating
18+
14+
PG
G
C8+
C
E
Downloadable
Rating
X
NC-17
R
PG-13
PG
G
NR
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
NR
BLOCK SETTING
CLEAR DOWNLOADABLE
RATING
Change
Password
Progressive Scan ON
OFF
TV Aspect
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
Contents
Set the font color of the displayed caption.
Set edge type of the displayed caption.
Set edge color of the displayed caption.
Set back opacity of the displayed caption.
Set back color of the displayed caption.
Set the viewing limitation according to US movie ratings.
Set the viewing limitation according to US TV program ratings.
Set the viewing limitation according to
Canadian French language Ratings.
Set the viewing limitation according to
Canadian English language Ratings.
To set the rating.
Clear the downloadable rating information and its setting.
Change the password.
Set to the progressive scan mode (set to "ON") or to the interlace scan mode (set to "OFF").
Set a picture size according to aspect ratio of your TV.
8 2 EN
E9M81UD_ZV457MG9.indd 82 2008/05/15 14:32:00
LIST OF SETTINGS
Setup
Video
Page 90
Recording
Clock
Pages 30-31
Channel
Pages 27-29
HDMI
Page 91
Reset All
Items (highlight is the default)
Video Input
Page 48
Auto Chapter
Page 39
L1(Rear)
L2(Front)
Daylight Saving Time
Video In
S-Video In
Video In
S-Video In
OFF
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
ON
OFF
Auto Finalize
Page 54
Disc Full
End of Timer Rec ON
OFF
Dubbing Mode Pages 50-51
Make Recording Compatible
Page 39
VCR DVD
DVD VCR
ON
OFF
Clock Setting
Auto Clock Setting OFF
Auto
Manual
ON(MAR-NOV)
ON(APR-OCT)
OFF
Auto Channel Preset
Antenna
Cable (Analog)
Cable (Analog/Digital)
Manual Channel Preset
TV Audio Select
Page 34
Stereo
SAP
Format
RGB
YCbCr
HDMI Audio
ON
OFF
RGB Range
Page 92
Normal
Enhanced
Yes
No
Contents
Set the video input type for the external input.
Insert chapter marks at even time interval.
Set the unit to finalize the disc automatically.
Set the dubbing direction.
Set to prohibiting additional recording (OFF) or to replace the title list after recording (ON).
Set the clock.
Set the clock automatically.
Set the clock for the daylight saving time.
Tune the channels automatically.
Tune the channels manually.
Set the analog TV audio type for output and recording.
Set the color space for the HDMI output.
Set whether to output the HDMI audio signal or not.
Set the black-white contrast level for HDMI
RGB output.
Set to the default setting.
Note
• Your change to each setting stays on even when the power is off except for Dubbing Mode.
• An item which is not currently available is grayed in the settings.
EN 8 3
2008/05/22 16:02:21 E9M81UD_ZV457MG9.indd 83
Playback
SOURCE DTV/TV
STANDBY-ON
SETUPS
Press [STOP
C
] if you are playing back a disc.
1 Press [SETUP] and use [
K
/
L
] to select “General Setting”, then press
[OK].
“General Setting” menu will appear.
2 Use [
K
/
L
] to select “Playback”, then press [OK].
General Setting
Playback
Display
Video
Recording
Clock
Channel
HDMI
Reset All
.
DISC MENU s
TITLE
B
RETURN j B
F
-h g
CHANNEL
+
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
3 Use [
K
/
L
] to select a desired item, then press [OK].
1
2
Parental Lock
Disc Audio
3
4
5
Disc Menu Language
Audio Language
Subtitle Language
6
7
Angle Icon
Still Mode
Submenu will appear.
4 Refer to 1 to 7 on pages 8 58 6 and set the selected item.
5 When you finish with setting, press
[SETUP] to exit.
8 4 EN
E9M81UD_ZV457MG9.indd 84 2008/05/15 14:32:00
SETUPS
Playback (cont’d)
1
Parental Lock (Default: OFF)
Some DVD-video feature a parental lock level. Playback will stop if the ratings exceed the levels you set, it will require you to enter a password before the disc will playback. This feature prevents your children from viewing inappropriate material.
Use [
K
/
L
] to select the desired level, then press [OK].
Parental Lock
OFF
8 [Adult]
7 [NC 17]
6 [R]
5 [PG R]
4 [PG 13]
3 [PG]
2 [G]
1 [Kid Safe]
If a password has not been set yet, proceed to A .
If a password has been set already, proceed to B .
Note
• Press [CLEAR] to erase numbers entered incorrectly.
• When you forget the password or you want to clear all settings in “Parental Lock” menu, enter 4,7,3,7 using [the Number buttons] in password input window. Password will be cleared and parental levels will be set to “OFF”.
2
Disc Audio
Choose the appropriate audio setting for your external device.
It will only affect a disc playback.
Use [
K
/
L
] to select a desired item, then press [OK].
Note
• Parental lock function may not be available to some discs.
• With some DVD, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.
• Record the password in case you forget it.
• If there is a DVD in the unit when you set up the parental lock, press [OPEN / CLOSE
A
] to activate the parental lock level.
A
A password has not been set yet.
Use [
K
/
L
] to select “Yes”. Use [the Number buttons] to enter a new password except for 4737, then press [OK].
Change Password?
Yes
No
Yes
Your setting will be activated.
Password Input
B
A password has been set already.
• Use [the Number buttons] to enter the current password.
Password Input
Your setting will be activated.
• If you want to change password, use [
K
/
L
] to select
“Yes”. Use [the Number buttons] to enter a new password, then press [OK].
<change the password>
Change Password?
Yes
No
Yes
Your setting will be activated.
Password Input
A
A
B
C
Disc Audio
Dynamic Range Control
PCM
Dolby Digital
Dynamic Range Control (Default : ON)
Set to “ON” to compress the range between soft and loud sounds.
Use [
K
/
L
] to select a setting, then press [OK].
Dynamic Range Control
ON
OFF
Your setting will be activated.
Note
• Dynamic range control function is available only on the discs which are recorded in the Dolby Digital format.
B
PCM (Default : 48kHz)
Use [
K
/
L
] to select a setting, then press [OK].
PCM
48kHz
96kHz
Your setting will be activated.
4 8 kHz : If your amplifier/decoder is NOT compatible with 96kHz PCM, select “48kHz”. 96kHz sound will be output in 48kHz.
9 6kHz : If your amplifier/decoder is compatible with
96kHz PCM, select “96kHz”. 96kHz sound will be output.
Note
When playing back disc with copyright protection
• Even if you select “96kHz”, the sound will be down sampled at 48kHz.
EN 8 5
E9M81UD_ZV457MG9.indd 85 2008/05/15 14:32:01
SETUPS
Playback (cont’d)
C
Dolby Digital (Default : Stream)
Use [
K
/
L
] to select a setting, then press [OK].
If “Other” is selected for 3 to 5 , press 4-digit code using [the Number buttons] .
Dolby Digital
PCM
Stream
Your setting will be activated.
PCM : Converts the Dolby Digital into PCM (2 channel).
When your amplifier/decoder is NOT compatible with Dolby Digital, set to “PCM”.
Stream : Outputs Dolby Digital signals
When your amplifier/decoder is compatible with Dolby Digital, set to “Stream”.
3
Disc Menu Language (Default : English)
Set the language for disc menu.
Use [
K
/
L
] to select a setting, then press [OK].
• When you finish entering the code, press [OK]. Refer to the language code table on page 100.
Note
-
Code Input
-
• Only the languages supported by the disc can be selected.
• Audio language setting may not be available to some discs.
• You can change or switch off the subtitles on a DVD also from the disc menu if it is available.
• Press [CLEAR] or [ s
] to erase numbers entered incorrectly.
Disc Menu Language
English
French
Spanish
Other
Your setting will be activated.
6
Angle Icon (Default : ON)
Set to “ON” to show the angle icon during the playback.
Use [
K
/
L
] to select a setting, then press [OK].
4
Audio Language (Default : Original)
Set the audio language.
Use [
K
/
L
] to select a setting, then press [OK].
Audio Language
Original
English
French
Spanish
Other
Your setting will be activated.
• When “Original” is selected, the audio language will be in the disc’s default language.
5
Subtitle Language (Default : OFF)
Set the subtitle language.
Use [
K
/
L
] to select a setting, then press [OK].
Subtitle Language
OFF
English
French
Spanish
Other
Your setting will be activated.
Angle Icon
ON
OFF
Your setting will be activated.
7
Still Mode (Default : Auto)
Select “Auto” usually.
Use [
K
/
L
] to select a setting, then press [OK].
Still Mode
Auto
Field
Frame
Your setting will be activated.
Auto : Optimum resolution setting (“Field” or
“Frame”) will be selected.
Field : Images in the still mode will be stabilized.
Frame : Images in the still mode will be highly defined.
Note
• Frame is 1 completed video image made up of 2 fields (There are 30 frames per second of NTSC video).
8 6 EN
E9M81UD_ZV457MG9.indd 86 2008/05/15 14:32:03
Display
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
CLEAR
.
DISC MENU
TITLE RETURN j B
F
-h g
CHANNEL
+
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
SETUPS
Press [STOP
C
] if you are playing back a disc.
1 Press [SETUP] and use [
K
/
L
] to select “General Setting”, then press
[OK].
2 Use [
K
/
L
] to select “Display”, then press [OK].
3 Use [
K
/
L
] to select a desired item, then press [OK].
1
2
OSD Language
Screen Saver
3
4
5
FL Dimmer
DTV CC
CC Style
6 V-Chip
Selection menu will appear.
4 Refer to 1 to 6 on pages 8 58 6 and set the selected item.
• For 4 and 5 refer to pages 35-37.
5 When you finish with setting, press
[SETUP] to exit.
1
OSD Language (Default : English)
Set the language for the on-screen display.
Use [
K
/
L
] to select a setting, then press [OK].
OSD Language
English
Français
Español
Your setting will be activated.
2
Screen Saver (Default : 10 minutes)
Set the time to activate the screen saver function on the
TV screen.
Use [
K
/
L
] to select a setting, then press [OK].
Screen Saver
OFF
5 minutes
10 minutes
15 minutes
30 minutes
Your setting will be activated.
EN 8 7
2008/05/15 14:32:04 E9M81UD_ZV457MG9.indd 87
SETUPS
Display (cont’d)
3
FL Dimmer (Default: Bright)
Set the front panel display brightness.
Use [
K
/
L
] to select a setting, then press [OK].
FL Dimmer
Auto
Bright
Dark
You can choose one from “Auto”, “Bright” and “Dark”.
If “Auto” is selected, the display gets dark when the power is off.
6
V-Chip
With the v-chip system in this unit, you can set the viewing limitation for the analog/digital TV programs received from the tuner or recorded on DVDs to prevent your children from watching inappropriate programs. If the unit detects a blocked program, a restriction message appears and you are not allowed to view or record the program.
1) Use [the Number buttons] to enter the access password.
If you have not set the password, first, use [the Number buttons] to set the access password, then press [OK] .
The number you entered will be stored as the access password.
Password Input
2) Use [
K
/
L
] to select a desired item, then press [OK].
A
E
F
B
C
D
V-Chip
MPAA Rating
TV Rating
Canadian French Rating
Canadian English Rating
Downloadable Rating
Change Password
A
MPAA Rating
B
TV Rating
C
Canadian French Rating
D
Canadian English Rating
You can set the viewing limitation according to MPAA rating (US movie ratings), TV Rating (US TV program ratings), Canadian French Rating (Canadian French language Ratings), Canadian English Rating (Canadian
English language Ratings).
1) Use [
K
/
L
] to select the desired rating, then press
[OK] repeatedly to switch between view and block.
When it is blocked a key icon will appear.
e.g.) MPAA rating
MPAA Rating
X
NC-17
R
PG-13
PG
G
NR
[MPAA Rating]
Rating
X
NC-17
R
PG-13
PG
G
NR
Category
Mature audience only
No one under 17 admitted
Restricted; under 17 requires accompanying parent or adult guardian
Unsuitable for children under 13
Parental guidance suggested
General audience
No rating
[TV Rating]
Rating
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
NR
Category
Mature audience only
Unsuitable for children under 14
Parental guidance suggested
General audience
Appropriate for all children 7 and older
Appropriate for all children
No rating
[Canadian French Rating]
Rating
1 8 ans+ Adult audience only
Category
16 ans+ Unsuitable for ages under 16
13 ans+ Unsuitable for ages under 13
8 ans+
G
E
Unsuitable for ages under 8
General audience
Exempt program higher lower higher lower higher lower
88 EN
E9M81UD_ZV457MG9.indd 88 2008/05/15 14:32:05
SETUPS
Display (cont’d)
[Canadian English Rating]
Rating
1 8 +
14+
PG
C
E
G
C 8 +
Category
Adult audience only
Unsuitable for ages under 14
Parental guidance suggested
General audience
For children over 8
For all children
Exempt program
As for TV Rating’s TV-MA, TV-14, TV-PG, or TV-Y7, you can further set the sub ratings to block specific elements of programming. Press [
K
/
L
/
{
/
B
] to select the desired rating or sub rating, then press [OK] repeatedly to switch between view and block. Sub rating status will appear on the side of the main rating.
TV Rating
FV V S L D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
NR
V
S
Sub Rating
FV
Category
Fantasy Violence
Violence
Sexual Situation
L
D
Coarse Language
Suggestive Dialogue higher lower
Rating
TV-Y7
TV-PG
TV-14
TV-MA
TV-PG, TV-14
Note
• Changing the main rating to block or view automatically changes all its sub ratings to the same
(block or view).
E
Downloadable Rating
Set the rating system via digital broadcasting, or clear the downloaded ratings.
If the broadcasting signal does not have the downloadable rating information, the message below will appear.
Downloadable Rating is currently not available.
•
This message will also appear when you try to access
“DOWNLOADABLE RATING“ after you have cleared the downloadable rating information, and the new information has not been downloaded since.
To set the rating:
Use [
K
/
L
] to select “BLOCK SETTING” then press [OK] to show the various types of ratings. Use [
K
/
L
] to select a desired rating to set, then press [OK] to show the levels for the rating. Use [
K
/
L
] to select a level, then press [OK] to switch “VIEW” or “BLOCK”. If you set one level to “BLOCK”, all the higher levels will be turned to “BLOCK” automatically.
To clear the downloadable rating information and its setting:
Use [
K
/
L
] to select “CLEAR DOWNLOADABLE
RATING”, then press [OK] .
F
Change Password
Change the current password.
Use [the Number Buttons] to enter new access password.
Note
• When you forget the access password at step 1), enter 4,7,3,7 using [the Number buttons] in the password input window. Password will be cleared.
• Depending on the type of rating system, you may set the levels individually.
EN 89
2008/05/15 14:32:06 E9M81UD_ZV457MG9.indd 89
SETUPS
Video
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
TUV
8
SPACE
0
ABC
2
JKL
5
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU
1
Progressive Scan (Default : OFF)
This unit is compatible with the progressive scan system.
The feature provides you with the higher definition images than the traditional output system does. To utilize this feature, you must set progressive scan mode to “ON”.
1) Use [
K
/
L
] to select “ON“, then press [OK].
Progressive Scan
ON
OFF
2) Use [
{
/
B
] to select “Yes“, then press [OK].
Activating progressive scan:
Check your TV has progressive scan and connect with component video cable.
TITLE RETURN j B
F
-h g
CHANNEL
+
REC MODE VCR DVD TIMER
NOTE :
If there is no picture or picture is distorted after selecting “Yes”,
Wait about 15 seconds for auto recovery.
Activate? Yes No
3) Use [
K
/
L
] to select “Yes“ within 15 seconds, then press [OK].
Your setting will be activated.
Press [STOP
C
] if you are playing back a disc.
1 Press [SETUP] and use [
K
/
L
] to select “General Setting”, then press
[OK].
2 Use [
K
/
L
] to select “Video”, then press [OK].
3 Use [
K
/
L
] to select a desired item, then press [OK].
1
2
Progressive Scan
TV Aspect
3 Video Input
Submenu will appear.
4 Refer to 1 to 2 on this page and set the selected item.
• For 3 refer to page 48.
5 When you finish with setting, press
[SETUP] to exit.
Note
• If your TV is compatible with progressive scan (525p /
480p), you are recommended to use the component video cable (commercially available) to connect this unit to the TV. (Refer to “Method 2” on page 18 or page 19.) If not, use the RCA video cable and set the progressive scan to “OFF” or press and hold [SETUP] for more than 3 seconds during DVD playback.
• When selecting “No” or not pressing any buttons on the unit or remote control within 15 seconds at step 3, progressive scan remains to be “OFF” (interlace scan).
2
TV Aspect (Default: 4:3 Letter Box)
You can select the TV aspect ratio to match the formats of what you are playing back with the unit and your TV screen (4:3 standard or 16:9 widescreen TV).
Use [
K
/
L
] to select a setting, then press [OK].
TV Aspect
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
If you have a standard TV:
Select “4:3 Letter Box”, so that black bars appear on the top and bottom of the TV screen when playing back a wide-screen picture. Select “4:3 Pan & Scan” for a full height picture with both sides trimmed when playing back wide-screen picture.
If you have a widescreen TV:
Select “16:9 Wide”.
9 0 EN
E9M81UD_ZV457MG9.indd 90 2008/05/15 14:32:06
SETUPS
HDMI
s
TITLE
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU
B
RETURN j B
F
-h g
CHANNEL
+
C
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
1 Press [SETUP] in stop mode and use
[
K
/
L
] to select “General Setting”, then press [OK].
2 Use [
K
/
L
] to select “HDMI”, then press [OK].
General Setting
Playback
Display
Video
Recording
Clock
Channel
HDMI
Reset All
3 Use [
K
/
L
] to select a desired item, then press [OK].
1
2
Format
HDMI Audio
3 RGB Range
4 When you finish with the setting, press [SETUP] to exit.
1
Format (Default : RGB)
You can select the color space for HDMI output.
Set the appropriate color space for your display device.
Use [
K
/
L
] to select a setting, then press [OK].
• When the connected device is not compatible with the
Y/Cb/Cr, HDMI signal is output as RGB regardless of the setting.
Format
RGB
YCbCr
Your setting will be activated.
2
HDMI Audio (Default : ON)
If you do not want to output the audio through HDMI
(when you digitally output the audio through the
COAXIAL DIGITAL AUDIO OUT jack to your audio system, etc.), you can set the HDMI audio output off.
Use [
K
/
L
] to select a setting, then press [OK].
• Set to “OFF” when the HDMI sound is not output.
HDMI Audio
ON
OFF
Your setting will be activated.
3
RGB Range (Default : Normal)
You can adjust the RGB range to make the dark areas of the HDMI images brighter.
Use [
K
/
L
] to select a setting, then press [OK].
• Select “Enhanced“ if the black-white contrast is not clear.
• This setting is effective only for HDMI RGB output.
RGB Range
Normal
Enhanced
Your setting will be activated.
• You cannot select HDMI when an HDMI cable is not connected and the items are shown in grey color.
EN 9 1
2008/05/15 14:32:07 E9M81UD_ZV457MG9.indd 91
Reset All
Reset the setting to default.
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
ABC
2
JKL
5
TUV
8
SPACE
0
DEF
3
MNO
6
WXYZ
9
CLEAR
DISC MENU s
TITLE
B
RETURN j B
F
-h g
CHANNEL
+
C
REC MODE VCR DVD TIMER
REC
I
HDMI AUDIO
CM SKIP D.DUBBING TIMER SET RAPID PLAY
SEARCH
SETUPS
1 Press [SETUP] and use [
K
/
L
] to select “General Setting”, then press
[OK].
“General Setting” menu will appear.
2 Use [
K
/
L
] to select “Reset All”, then press [OK].
3 Select “Yes” using [
K
/
L
] , then press
[OK].
Reset to factory default?
Yes
No
4 Select “Yes” again using [
K
/
L
] , then press [OK].
Are you sure?
Yes
No
Your setting in recording will be initialized.
Note
• The settings listed below will remain unchanged even after resetting to the factory default.
– OSD language setting
– Channel setting
– Clock setting
– Parental lock setting
– V-Chip setting
– Timer programming information
9 2 EN
E9M81UD_ZV457MG9.indd 92 2008/05/15 14:32:08
VCR FUNCTIONS
Recording Playback
Press [VCR] first.
1) Insert a prerecorded tape (refer to page 25 on how to insert a cassette tape).
2) Press [PLAY
B
] to start playback.
3) Press [STOP
C
] to stop playback.
To pause playback:
Press
Playback will pause and sound will be muted.
Press
[PAUSE ] .
To resume playback:
[PLAY
Note
B
F
] .
• When a cassette tape without erase-protection tab is inserted, the unit will start playback automatically.
• Tracking will be automatically adjusted upon playback. To adjust the tracking manually, press
[CHANNEL / ] on the remote control.
• S-VHS cassette tape is not available on this unit.
Press [VCR] first.
1) Insert a recordable tape with an erase-protection tab intact.
Accidental erasure prevention
To prevent accidental recording on a recorded cassette tape, remove its eraseprotection tab. To record on it later, cover the hole with cellophane tape.
erase-protection tab
2) Select the recording mode using [REC MODE].
• The desired recording mode is selected in SP
(standard play) or SLP (super long play) mode by pressing [REC MODE] .
Recording mode:
Tape speed
Type of tape
SP mode
SLP mode
Recording
T60
1hour
3hours
/ playback time
T120
2hours
6hours
T160
2-2/3hours
8hours
3) Select stereo or SAP. Refer to page 34.
4) Select the desired channel to record using
[CHANNEL
/
] or [the Number buttons].
5) Press [REC
I
] to start recording.
[STOP ] to stop the recording.
To pause recording:
Press [PAUSE
F
] .
To resume recording:
Press [PAUSE
F
] or [REC
I
] .
After the unit has been in pause mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage.
• Refer to pages 42-45 for instructions on timer recording.
EN 9 3
2008/05/15 14:32:09 E9M81UD_ZV457MG9.indd 93
VCR FUNCTIONS
One-touch Timer Recording (OTR) Index Search
This feature allows you to set the recording length simply by pressing [REC
I
] on the remote control.
Press [VCR] first.
An index mark will be assigned at the beginning of each recording you make. You may skip to a specific marked point by following the steps below.
1) Insert a recordable tape with an erase-protection tab intact.
2) Select the recording mode using [REC MODE].
(Refer to “Recording” on page 93.)
Press [VCR] first.
1) Press [SEARCH] so that “INDE X SEARCH” menu appears.
2) Using [the Number buttons], enter the number of recordings you wish to skip within 30 seconds.
3) Select stereo or SAP. Refer to page 34.
INDEX SEARCH
03
4) Select the desired channel to record using
[CHANNEL
/
] or [the Number buttons].
5) Press [REC
I
] to begin the one-touch timer recording.
You can select a fixed recording time by pressing
[REC
I
] repeatedly.
(0:30) (1:00)
(Normal recording)
(8:00) (7:30)
When the one-touch timer recording is finished, the unit will turn off automatically.
To change the recording length during the onetouch timer recording:
Press [REC
I
] repeatedly until the desired length appear.
3) Press [
E
], [
D
] to start index search.
If you want to go in the forward direction, press [
D
] .
If you want to go in the reverse direction, press [
E
] .
After index search, the VCR will play back the cassette tape automatically.
CURRENT PROGRAM
Beginning of tape
End of tape
02
Pro.1
Pro.2
Pro.3
Pro.4
Pro.5
01 01 02 03
INDEX MARK
Note
• You can make the index mark up to 20.
To cancel the one-touch timer recording within the specified time:
Press [STOP
C
] .
Note
• The remaining recording time will be displayed on the front panel display during one-touch timer recording. Press [DISPLAY] to see it on the TV screen.
• You cannot pause the one-touch timer recording.
• If VCR one-touch timer recording is completed during DVD playback or recording, the VCR will be in stop mode and the DVD keeps the current mode.
• Unlike a timer recording, you can perform the following operations during the one-touch timer recording.
- Turning off the power to stop one-touch timer recording.
I
] or [STOP
C
] on the remote control.
• When the one-touch timer recording is finished and the power is turned off, the unit will switch to the timer standby mode automatically if a timer recording has been programmed. Press [TIMER SET] to cancel the timer standby mode for using the unit continuously.
9 4 EN
E9M81UD_ZV457MG9.indd 94 2008/05/15 14:32:10
VCR FUNCTIONS
Other Operations Time Search
This feature allows you to go to a specific point on a cassette tape by entering the exact amount of time you wish to skip in order to reach the point.
Press [VCR] first.
1) Press [SEARCH] repeatedly so that “TIME SEARCH” menu appears.
2) Using [the Number buttons], enter your desired time to skip within 30 seconds.
You can set the time up to 9:59.
TIME SEARCH
2:50
3) Press [
E
], [
D
] to start time search.
If you want to go in the forward direction, press
[
D
] .
If you want to go in the reverse direction, press
[
E
] .
After time search, the unit will play back the cassette tape automatically.
Note
• Index search and time search are not available during recording.
• Press [STOP
C
] to stop the search.
• If the end of the cassette tape is reached during search, this unit will cancel the search and rewind the cassette tape.
Press [VCR] first.
Fast forward:
When the unit is in stop mode, press [
D
] to fast forward the cassette tape.
Rewind:
When the unit is in stop mode, press [
E
] to rewind the cassette tape.
To cue or review picture during playback (picture search):
Press [
E
] , [
D
] during playback.
Press it again and the unit will search in super high speed. (in the SLP mode only)
To freeze the picture on TV screen during playback
(still mode):
Press [PAUSE
F
] . Each time you press the button, the picture will be forwarded by one frame.
If the picture begins to vibrate vertically during the still mode, stabilize the picture by pressing [CHANNEL / ] on remote control.
If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if equipped.
Counter reset:
Press [CLEAR] to reset the counter to “0:00:00”.
To playback in slow motion:
Press [PAUSE
F
] during playback, then press [
D
] .
Press [
D
] or [
E
] repeatedly to select the desired speed.
Automatic rewind:
When a cassette tape is played back or fast forwarded to its end, the cassette tape will rewind to the beginning, stop and eject itself.
When you playback a cassette tape recorded in Hi-Fi stereo:
Press [AUDIO] on the remote control to select Hi-Fi or
MONO for playback sound mode.
• If you have connected a stereo TV to this unit, select “HIFI”.
• If you have connected a monaural TV to this unit, select
“MONO”.
Your Selection
Type of recorded tape non Hi-Fi tapes
Hi-Fi tapes recorded in
Hi-Fi stereo
Hi-Fi tapes recorded main audio program
Hi-Fi tapes recorded second audio program
L-channel
Monaural
L
Main audio program
HIFI
R-channel
Monaural
R
Main audio program
MONO
Monaural
L+R
Main audio program
Second audio program
Second audio program
Second audio program
Note
• Still/slow mode will stop after 5 minutes to prevent damage to the cassette tape and the video head.
• To return to playback from the picture search/still/ slow mode, press [PLAY
B
] .
EN 9 5
2008/05/15 14:32:10 E9M81UD_ZV457MG9.indd 95
TROUBLESHOOTING
Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing.
Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.
Symptom Remedy
The power does not turn on.
• Check that the AC power cord is connected securely.
• Check the breaker (in case of power failure).
• Press [TIMER SET] to cancel the timer standby mode.
There is no picture.
TV program reception does not fill the
TV screen.
• Re-connect the connecting cords securely.
• Check if the connecting cords are damaged.
• Check the connection to your TV (pages 18-19).
• Switch the input selector on your TV (such as to “L1”) so that the signal from the unit appears on the TV screen.
• Try to set the channels with “Auto Channel Preset” or “Manual Channel
Preset” in “Channel” menu (pages 27-29).
• Select a channel of any TV program using [CHANNEL / ] .
TV program pictures are distorted.
TV channels cannot be changed.
There is no sound or the sound is distorted.
• Adjust TV antenna.
• Adjust the picture. (Refer to the TV’s instruction manual.)
• Place the unit and TV farther apart.
• Place the TV and any bunched RF coaxial cables farther apart.
• Switch the input to TV.
• Connect the RF coaxial cable correctly (pages 15-17).
• Re-connect all connections securely.
• Check if the connecting cord is damaged.
• Check the connections to the amplifier input.
• Check if the input device setting on the amplifier is correct.
• When the unit is in pause mode or in slow-motion playback mode, sound is not output. This is not a malfunction.
• When the unit is in fast forward or fast reverse mode, sound is not output. This is not a malfunction.
• If using the HDMI connection, sound is not output when “HDMI Audio” is set to “OFF”.
• Check the RCA audio cable connection. If you are using HDMI-DVI conversion cable, you must connect the RCA audio cable, too.
• If using the HDMI connection, check whether the output format of this unit
(HDMI FORMAT) matches the supported input format of other connected device.
The remote control does not function.
• Batteries are weak.
• There are obstacles between the remote control and the unit.
• The remote control is far from the unit.
• There are no batteries in the remote control.
• Check if the unit is turned on.
• Check if you are pointing the remote control at the recorder and NOT the TV.
If you have a plasma TV, it may interfere with the IR signal. Try the remote with the plasma off. If the remote works, you may need to move the unit away from the plasma TV.
• Press [DVD] or [VCR] , whichever you need. Then, try again.
• Press [TIMER SET] to cancel the timer standby mode.
The unit does not operate properly.
No analog TV closed captions are output.
• When static electricity, etc., causes the unit to operate abnormally, unplug the unit and then plug it in again.
• If you are using HDMI connection to watch the TV programs through this unit’s tuner, analog TV closed caption cannot be output. Try using other connection.
Playback picture is distorted.
• Keep the device which may cause electrical disturbances, such as a cellular phone, away.
• Set the TV’s input to “TV.” The channel cannot be changed from the channel you are recording.
Nothing was recorded even though you set the timer setting correctly.
Timer recording is not complete or did not start from the beginning.
Timer recording is impossible.
• There was a power failure during recording.
• The unit’s internal clock stopped due to a power failure that lasted for more than 30 seconds. Reset the clock (pages 30-31).
• The program contains copy protection signals that restricts copying.
• The timer setting overlapped with another setting that has priority.
• The timer setting overlapped with another setting that has priority (page 45).
• Disc space was not enough.
• Make sure appears on the front panel display of this unit. If not, press
[TIMER SET] .
9 6 EN
E9M81UD_ZV457MG9.indd 96 2008/05/15 14:32:11
TROUBLESHOOTING
Symptom
There is no picture.
Picture noise appears.
There is no sound.
Sound is noisy.
No DTS sound is output.
The disc does not play back.
Discs recorded on this unit cannot be played back on other DVD players.
The disc does not start playback from the beginning.
The unit starts playing back the disc automatically.
Some functions such as stop, search, or slow-motion playback cannot be performed.
The language for the sound track cannot be changed.
Remedy
• If the main menu appears on the TV screen, press [RETURN] to exit.
• Check if the progressive scan mode is set correctly according to your TV
(page 90).
• Clean the disc with a cleaning cloth.
• If you are using DIGITAL AUDIO OUT (COAXIAL) jack, check the setting in
“Disc Audio” (pages 85-86).
• Clean the disc with a cleaning cloth.
• Clean the disc with a cleaning cloth.
• This unit is not compatible with DTS sound.
• No disc is inserted.
• A blank disc is inserted.
• The disc is upside down. Insert the disc with the labeled side facing up.
• The disc is not correctly inserted.
• The unit cannot play back certain discs (such as a CD-ROM) (page 55).
• The region code on the DVD-video does not match the unit (page 55).
• Moisture has condensed inside the unit. Remove the disc and leave the unit turned on for about 2 hours until the moisture evaporates (page 4).
• If the disc was recorded on another recorder, the unit cannot play back the disc if it was not finalized.
• If you are using DVD-RW/-R, please ensure you finalized the disc after recording (pages 53-54).
• Resume playback was activated (page 61). Press [STOP
C
] twice.
• You have inserted a disc whose title menu or DVD menu automatically appears on the TV screen when it is first inserted.
• The DVD-video features an auto playback function.
• Depending on the disc, you may not be able to do some of the operations. Refer to the instruction manual supplied with the disc.
• The title does not have the multilingual audio tracks.
• The DVD-video prohibits the changing of the language for the sound track.
• Multilingual subtitle are not recorded on the DVD-video.
The subtitle language cannot be changed or turned off.
The angles cannot be changed.
Recording does not stop immediately after you press press [OPEN
Repairing
/
[STOP
CLOSE repairing process.
A
C
The disc tray does not open when you
] .
] .
“Repairing” appears on the TV screen.
In a case you intend to cancel the
Do you want to cancel a repairing process? When selecting “Yes”, the disc may not be usable.
Yes
No
• Multi-angles are not recorded on the DVD-video being played back.
• The angle-change operation is whenever possible as long as the disc contains a multi-angle portion. Actual change will be performed when the portion has come up.
• The DVD-video prohibits changing angles.
• Try changing the angle using the DVD-video’s menu.
• It may take a few seconds for the unit to input disc data before recording stops.
• It may take a few seconds for the disc tray to open after you have recorded or edited a disc. This is because the unit is adding disc data to the disc.
• If there is a power failure or unplugging during recording, finalizing, formatting or editing (even after “Repairing” disappears), a repairing process will begin automatically just after turning the unit on again.
It may take several minutes up to about several hours.
• If you intend to cancel the repairing process, press [OPEN / CLOSE
A
] on the front panel, then select “Yes” and press [OK] . After that, press
[OPEN / CLOSE
A
] to take out the disc. The disc canceled during the repairing process MAY NOT work.
Repairing
EN 9 7
2008/05/15 14:32:12 E9M81UD_ZV457MG9.indd 97
TROUBLESHOOTING
Symptom
There is no picture.
Picture noise appears.
Remedy
• If you connect the cable to S-VIDEO OUT/ COMPONENT VIDEO OUT /
HDMI OUT jack, connect it to AUDIO / VIDEO OUT jack instead.
• Head cleaning for VCR may be necessary. Refer to “Auto head cleaning”
(page 5).
• Adjust tracking control for better picture by pressing [CHANNEL / ] while you are playing back a cassette tape.
The cassette tape does not play back.
• No cassette tape is inserted.
Recording does not start after you press
[REC
I
] .
• Make sure the cassette tape has an erase-protection tab when you record to a cassette tape. If needed, cover the hole with cellophane tape.
The remote control does not function.
• Check if a cassette tape is in this unit.
The motor rotates even when playback / recording is stopped.
• The motor may rotate for the duration of approximately 5 minutes for efficient operation. This is not a malfunction.
Frequently Asked Questions
– Can I record to CD-RW/-R?
– Can I play back DVD-video that is bought in another country?
– Can I connect the unit to my PC?
– Can I program a timer recording with cable/satellite box?
– Can I record one channel while watching another channel using a cable / satellite box?
– Can I connect this unit directly to a TV which only has an antenna in jack using an RF coaxial cable?
– Can I change the channels on the cable / satellite box using the remote control of this unit?
No, this unit records only DVD.
Possible when the region code of the disc is 1 and All.
No, you cannot control the unit by PC.
Yes, you can. Select “L1” or “L2” as your recording channel, and leave the cable / satellite box on (pages 17, 42-45).
It depends on your connection configurations. For more details, please kindly contact your cable / satellite provider.
No. You need an RF modulator (commercially available) to connect this unit to a TV which only has an antenna in jack (page 16). This unit does not have an RF modulator.
No. Changing the channels on the cable / satellite box using this unit’s remote control is not possible. You need to use the remote control supplied with the cable / satellite box to change the channels on the cable / satellite box.
Note for Output Jacks on the Rear Panel
1
HDMI OUT
DIGITAL
AUDIO OUT
COAXIAL
R
OUT
AUDIO
OUT
DVD
S-VIDEO
COMPONENT
VIDEO OUT
Y
S-VIDEO
DVD/VCR
IN --- AUDIO --- OUT
L
OUT
P
/C
B
IN
L
R
IN --- VIDEO --- OUT
R
L
ANTENNA
IN
P
/C
R
2 3 4 5
Available for
Output Jacks
1
HDMI OUT
2 COA X IAL DIGITAL AUDIO OUT
3 AUDIO OUT
4
S-VIDEO OUT
5 COMPONENT VIDEO OUT - interlace
5
COMPONENT VIDEO OUT - progressive
6
AUDIO / VIDEO OUT
✔
:
DVD mode
: Not available
✔
✔
✔
✔
✔
✔
✔
VCR mode
✔
6
98 EN
E9M81UD_ZV457MG9.indd 98 2008/05/15 14:32:12
TROUBLESHOOTING
Disc Error message
Disc Error
— Please eject the disc. —
Playback feature may not be available on this Disc.
Region Error
— Please eject the disc. —
Playback is not authorized in your region.
Parental Lock On
The current selected parental level prohibits playback.
Cause
• Unplayable disc is inserted in the unit.
• The disc is upside down.
• Playback is not authorized in the region of the DVD-video which you inserted in the unit.
• The current selected parental level prohibits playback.
Solution
• Insert the standardized disc which bear the marks on page 55.
• Insert the disc with the labeled side facing up.
• Insert the DVD-video with region codes
1 or ALL.
• Check “Parental Lock” setting in
“Playback” menu (page 85).
Recording Error
This program is not allowed to be recorded.
Recording Error
This program is not recordable in +VR mode.
Recording Error
Can not record on this disc.
Recording Error
This disc is protected and not recordable.
• The recording function encountered the copy prohibited program.
• You are trying to record the copy-once program.
• You are trying to record onto the disc which is unrecordable, or the disc status is unable to record.
• The disc is dirty.
• The disc is damaged.
• You are trying to record on to the protected disc which is set in “Disc Edit” menu.
• You are trying to record onto the disc which has no space for recording.
• You cannot record copy prohibited programs.
• You cannot record the copy-once program.
• Insert the recordable disc, and ensure the disc status satisfies the recording requirements (page 38).
• Clean the disc with a cleaning cloth.
• Replace the disc.
• Release the disc protect setting in “Disc
Edit” menu (page 52).
Recording Error
Disc is full.
(No area for new recording)
Recording Error
You cannot record more than 49 titles on one disc.
(The maximum is 49)
Recording Error
You cannot record more than 254 chapters on one disc.
(The maximum is 254)
Recording Error
You cannot record on this disc as Power
Calibration Area is full.
Recording Error
This disc is already finalized.
Recording Error
The disc has no recording compatibility.
Set “Make Recording Compatible” to
“ON” to convert the disc.
• You are trying to record onto the disc on which the number of recording titles comes up to the maximum (49).
• You are trying to record onto the
DVD+RW or DVD-RW on which the number of recording chapters comes up to the maximum (254).
• When recordings are performed repeatedly onto an unstable disc, this area may come up to be full.
• Every time you insert a disc for recording, the disc’s working area will be taken up. And if you repeat this frequently, it will be used up sooner and you may not be able to record full
49 titles.
• You are trying to record onto the disc already finalized.
• You are trying to record onto the disc that had been recorded by other recorders.
• Insert the recordable disc with enough recording space.
• Delete unnecessary titles (page 70).
• Delete unnecessary chapter marks
(pages 73-74).
• Insert a new disc.
• Release the finalizing for this disc
(page 53).
• Set “Make Recording Compatible” to
“ON” to rewrite the menu, after that you will record to disc (page 39).
* If you are still having trouble with the unit after checking “TROUBLESHOOTING”, write down the error code and the error description for calling our help line mentioned on the front page to locate an Authorized Service Center.
EN 99
2008/05/15 14:32:13 E9M81UD_ZV457MG9.indd 99
Language
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Estonian
Faroese
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Interlingue
Inupiak
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean
Kurdish
Laothian
Latin
Latvian; Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Occitan
Oriya
Oromo (Afan)
Panjabi
Pashto; Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Romanian
LANGUAGE CODE
Code Language Code Language
7254
4961
5464
4965
5047
6058
5160
5161
4854
4855
4864
4853
5971
4851
5759
4947
4765
4771
4772
4847
5167
4860
5072
4748
4747
4752
6563
4759
4764
5471
5051
5158
5758
5360
5367
5447
5569
5455
5166
5261
5256
5255
5264
5271
5358
5747
5866
5957
5953
5965
5958
5966
5955
5964
5771
6460
5761
5767
5861
5847
5868
5860
5566
5647
5669
5760
5765
5757
6469
5467
5565
5560
5547
5551
5557
5347
6247
6265
5247
6258
6266
6367
6459
6461
5961
5960
6047
6051
6061
6149
6164
6159
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Slovenian
Somali
Spanish
Sundanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Russian
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Code
6647
6666
6651
6654
4861
6655
6661
6665
6558
6561
5165
6567
6569
6568
6658
6653
6566
6660
6560
6550
6555
6565
6557
6467
6559
6553
6547
5350
6564
6554
4971
6961
7054
5655
7161
7267
6664
6657
6669
6757
6764
6772
6855
6861
100 EN
E9M81UD_ZV457MG9.indd 100 2008/05/15 14:32:13
GLOSSARY
Ana l og Audio
An electrical signal that directly represents sound.
Compare this to digital audio which can be an electrical signal, but is an indirect representation of sound. See also
“Digital Audio”.
PBC (p l ayback contro l ) (video CD on l y
This function enables you to play back interactive software using a menu screen. See also “Video CD”.
Aspect Ratio
The width of a TV screen relative to its height.
Conventional TVs are 4:3 (in other words, the TV screen is almost square); widescreen models are 16:9 (the TV screen is almost twice as wide as it is high).
Chapter (DVD on l y
PCM (pu l se code modu l ation)
The most common system of encoding digital audio, found on CD and DAT. Excellent quality, but requires a lot of data compared to formats such as Dolby Digital and MPEG audio. For compatibility with digital audio recorders (CD, MD and DAT) and AV amplifiers with digital inputs, this unit can convert Dolby Digital and
MPEG audio to PCM. See also “Digital Audio”.
Progressive Scan (5
2
p / 4 8 p
Just as a book is split up into several chapters, a title on a
DVD is usually divided into chapters. See also “Title”.
Component Video Out
Each signal of luminance (Y) and component (P
B
/C
B
, P
R
/
C
R
) is independent to output so that you can experience picture color as it is.
Also, due to compatibility with progressive video
(525p/480p), you can experience higher-density picture than that in interlace (525i/480i).
Digita l Audio
An indirect representation of sound by numbers. During recording, the sound is measured at discrete intervals
(44,100 times a second for CD audio) by an analogto-digital converter, generating a stream of numbers.
On playback, a digital-to-analog converter generates an analog signal based on these numbers. See also
“Sampling Frequency” and “Analog Audio”.
A type of display that does not split each frame into fields, and instead scans directly through all the scanlines of each frame in order. Progressive scan provides less flickering and higher image resolution than traditional
(525i/480i) TV signals. Refer to page 90 for instructions on selective progressive scan mode.
Region Code
Regions associate discs and players with particular areas of the world. This unit will only play back discs that have compatible region codes. You can find the region code of your unit by looking on the rear panel. Some discs are compatible with more than one region (or all regions).
Samp l ing y
The rate which sound is measured by a specified interval to turn into digital audio data. The numbers of sampling in one second defines as sampling frequency. The higher the rate, the better the sound quality.
Do l by Digita l
SAP (secondary audio p g
The system to compress digital sound developed by
Dolby Laboratories. It offers you sound of stereo(2ch) or multi channel audio.
Sub-audio channel which is delivered separately from main-audio channel. This audio channel is used as an alternate in bilingual broadcasting.
Fina l ize
To make DVD, which have been recorded on, possible to play back in DVD players. With this unit, it is possible to finalize DVD+R, DVD-RW, and DVD-R.
S-Video Output
It delivers independently each signal of color(C) and luminance(Y) to TV as video signals, so that higher-quality picture will be gained.
HDMI ™ (high definition mu l timedia interface)
A digital interface between audio and video source. It can transmit component video, audio, and control signal with one cable connection.
Tit l e (DVD on l y)
A collection of chapters on DVD. See also “Chapter”.
Track
MP
3
(MPEG audio l ayer
3
)
MP3 is a method of compressing files. You can copy MP3 files on CD-RW/-R from the computer and play back the files on this unit.
Audio CD use tracks to divide up the content of a disc. The DVD equivalent is called a chapter. See also
“Chapter”.
Video CD
A digital format for store video data in compact disc.
+ VR Mode
+ VR mode is a recording format for DVD+RW/DVD+R/
DVD-RW/DVD-R discs. This format allows disc editing features to be available in our DVD Recorder.
EN 101
2011/09/14 14:33:49 E9M81UD̲ZV457MG9̲EN̲v3.indd 101
Recording discs
SPECIFICATIONS
General
VCR video heads
Power requirements
Power consumption
Dimensions (width x height x depth)
Weight
Operating temperature
Operating humidity
TV system
Recording
Recording format
Four heads
120V AC +/-10%, 60Hz +/-5%
30W (standby: 3.3W)
17.2 x 4.0 x 10.3 inches (435 x 99.5 x 260mm)
9.5 lbs. ( 4.3kg )
41°F (5°C) to 104°F (40°C)
Less than 80% (no condensation)
ATSC / NTSC-M TV standard
+VR (video recording) format
DVD+Rewritable, DVD+Recordable
DVD-Rewritable, DVD-Recordable (+VR mode only)
Video recording format
Sampling frequency
Compression format
13.5 MHz
MPEG
Audio recording format
Sampling frequency
Compression format
Tuner
Tuning system
Channel coverage (ATSC / NTSC)
Terrestrial
CATV
Terminals
Audio input
RCA jack x 2
Video input
RCA jack x 1
S-video input
Mini DIN 4-pin x 1
VHF / UHF / CATV input and output
F-type
Audio input
RCA jack x 2
Audio output
RCA jack x 4
Video input
RCA jack x 1
Video output
RCA jack x 1
S-video input
Mini DIN 4-pin x 1
S-video output
Mini DIN 4-pin x 1
Component video out
RCA jack x 3
Coaxial digital audio out
RCA jack x 1
HDMI output
Jack
48 kHz
Dolby Digital
Channel frequency synthesized tuning system
VHF 2~13, UHF 14~69
2~13, A~W, W+1~W+94 (analog W+1~W+84), A-5~A1, 5A
2V rms (input impedance: more than 22kΩ)
1Vp-p (75Ω)
Y: 1Vp-p (75Ω) C: 286mVp-p (75Ω)
75Ω unbalanced
2V rms (input impedance: more than 22kΩ)
2V rms (output impedance: more than 1kΩ)
1Vp-p (75Ω)
1Vp-p (75Ω)
Y: 1Vp-p (75Ω) C: 286mVp-p (75Ω)
Y: 1Vp-p (75Ω) C: 286mVp-p (75Ω)
Y: 1Vp-p (75Ω) P
B
/C
B
: 700mVp-p (75Ω)
500mVp-p (75Ω)
HDMI jack
P
R
/C
R
: 700mVp-p (75Ω)
Note
• The specifications and design of this product are subject to change without notice.
102 EN
E9M81UD_ZV457MG9.indd 102 2008/05/15 14:32:13
ESPAÑOL
Disco Grabable Discos Reproducibles
Este aparato es compatible con la reproducción de los siguientes discos y archivos.
Discos reproducibles
DVD-video
Logotipos
Este aparato puede grabar a DVD+RW, DVD+R, DVD-RW y
DVD-R.
Los discos DVD+R/DVD-R pueden ser grabados sólo una vez. Los discos DVD+RW/DVD-RW pueden ser grabados y borrados muchas veces.
En este aparato los discos DVD-RW / -R serán grabados automáticamente en el modo DVD+VR.
Logotipo Atributos
DVD+RW
DVD+R
DVD-RW
(Sólo discos en modo de video finalizados)
DVD-R
(Sólo discos en modo de video finalizados)
CD-DA (CD de audio)
CD de video
CD-RW
CD-R
Archivos reproducibles
CD-DA
MP3 es una marca registrada de
DVD Format/Logo Licensing Corporation.
Medio
CD-RW/-R
Códigos de Región
El número presente en el interior el globo se refiere a una región del mundo.Este aparato puede reproducir discos DVD que estén rotulados para ALL las regiones o para la región 1.
DVD+RW DVD+R
Disco de 8 cm / 12 cm, un solo lado, una sola capa
Tiempo de grabación máx. aprox.
(modo SLP):
360 minutos (4,7 GB) (para 12 cm)
108 minutos (1,4 GB) (para 8 cm)
DVD-RW DVD-R
• Los siguientes discos se recomiendan para obtener una buena calidad de grabación y han sido comprobados como compatibles con este aparato. Sin embargo, según sea la condición del medio el equipo podría no leer el disco correctamente.
Verbatim
JVC
Maxell
SONY
TDK
DVD+R 8x,
DVD-R 8x,
DVD-RW 4x
DVD+R 4x/8x/16x
DVD+RW 4x,
DVD-RW 2x
DVD+R 4x/8x/16x, DVD-R 8x/16x
DVD+R 4x/8x/16x, DVD+RW 4x
El comportamiento de cualquier otro disco no está garantizado.
• Usted puede reproducir discos DVD+RW en la mayoría de los reproductores de DVD sin finalizarlos.
Sin embargo, si usted ha añadido o eliminado capítulos, u ocultado capítulos, debe ejecutar
“Compatibilizar edic.” antes de poder ver dichos efectos en otros equipos. (Consulte la página 8 0.)
Para reproducir discos que no sean DVD+RW en otros reproductores de DVD, usted necesitará finalizarlos.
Disco no Grabable
• Un DVD-RW grabado en un modo distinto de +VR no será grabable en este aparato a menos que usted borre todo el contenido del disco. (Consulte la página 79.)
• Un DVD-R grabado en un modo distinto de +VR no será grabable en este aparato.
ES 103
2008/05/15 14:32:13 E9M81UD_ZV457MG9.indd 103
ESPAÑOL
Conexión Básica
1) Desconecte el cable de alimentación de su televisor del tomacorriente de CA.
2) Efectúe la conexión básica ilustrada más abajo.
parte trasera de este aparato
HDMI OUT
DVD/VCR
S-VIDEO IN --- AUDIO --- OUT
L
DVD
S-VIDEO
L
OUT
Y
P B
/C B
OUT
S-VIDEO
DVD/VCR
IN --- AUDIO --- OUT
IN
L
R
IN --- VIDEO --- OUT
L
ANTENNA
IN
R
P R
/C R
IN
R
IN --- VIDEO --- OUT
OUT cable coaxial de RF
IN
ANTENNA parte trasera de su televisor cable coaxial de RF cable de audio RCA cable de video RCA
Esta conexión es sólo para el procesamiento de cada elemento de la señal de TV
R L
AUDIO IN VIDEO IN
ANT. IN o antena de
VHF / UHF empresa de
TV por cable
3) Enchufe los cables de alimentación de los aparatos al tomacorriente de CA.
Conexión a Una Caja de TV por Cable / Satelital
1) Desconecte el cable de alimentación de su televisor del tomacorriente de CA.
2) Efectúe la conexión como se ilustra abajo.
ej.)
HDMI OUT cable de S-video cable de video RCA o cable de audio RCA parte trasera de este aparato
DVD/VCR
AUDIO
DVD
S-VIDEO DIGITAL
AUDIO OUT OUT S-VIDEO IN --- AUDIO --- OUT
COMPONENT
VIDEO OUT
Y
S-VIDEO
DVD/VCR
IN --- AUDIO --- OUT
COAXIAL
L OUT
P
B
/C
IN
OUT
L
R
IN --- VIDEO --- OUT
L
IN
ANTENNA
R
P
R L R
IN
R
IN --- VIDEO --- OUT cable de video RCA
OUT
IN
ANTENNA cable coaxial de RF
Esta conexión es sólo para el procesamiento de cada elemento de la señal de TV
ANT. IN parte trasera de su televisor cable de audio RCA cable coaxial de RF
R L
AUDIO OUT VIDEO OUT
S-VIDEO
OUT caja de TV por cable/satelital
RF OUT ANT. IN cable coaxial de RF antena parabólica satelital o
VIDEO IN
R L
AUDIO IN empresa de
TV por cable
3) Enchufe los cables de alimentación de los aparatos al tomacorriente de CA.
104 ES
E9M81UD_ZV457MG9.indd 104 2008/05/15 14:32:14
Configuración Inicial
Cuando usted encienda este aparato por primera vez necesita seguir estos pasos.
1 Presione [STANDBY-ON ].
Encienda el televisor. Seleccione la entrada a la cual está conectado el aparato.
2 Utilice [
K
/
L
] para seleccionar su idioma deseado, y luego presione
[OK] para establecerlo.
Initial Setup
OSD Language
English
Français
Español
3 Utilice [
K
/
L
] para seleccionar el tipo de señal de emisión, y luego presione
[OK].
Ajuste inicial
Ajuste de Canal
Verificar que la antena esté conectada a la toma "ANTENNA IN".
Antena
Cable (Analógico)
Cable (Analógico/Digital)
ESPAÑOL
El equipo comenzará a obtener los canales disponibles en su región.
4 Utilice [
{
/
B
] para seleccionar un elemento a configurar, y utilice [
K
/
L
] para seleccionar el contenido de su preferencia, y luego presione [OK].
Ajuste inicial
Grabación Básica
1
Presione [DVD].
Presione [OPEN / CLOSE
A
] para abrir la bandeja de discos e insertar su disco con el rótulo aupntando hacia arriba. Presione de nuevo
[OPEN / CLOSE
A
] para cerrar la bandeja de discos.
* Asegúrese de que el disco sea compatible con este aparato.(Para obtener la lista de discos compatibles consulte la página 38.)
2 Para seleccionar un modo de grabación presione [REC MODE].
Modo de grabación
Tiempo de grabación
Calidad del video y el sonido
Disco de 8 cm Disco de 12 cm
Buena HQ (1Hr)
SP (2Hr)
18 min
36 min
60 min
120 min
SPP (2.5Hr)
LP (3Hr)
EP (4Hr)
SLP (6Hr)
45 min
54 min
72 min
108 min
150 min
180 min
240 min
360 min
Deficiente
3 Presione [DTV / TV] para seleccionar TV analógica o TV digital, y a continuación, utilice [CHANNEL / ] o [los botones numéricos] y [ • ] (para canales de TV digital) para seleccionar un canal que desea grabar.
4 Presione [REC
I
] para iniciar la grabación.
Para configurar la grabación a un toque con temporizador (OTR)...
Esta es una manera sencilla de configurar el tiempo de grabación en bloques de 30 minutos.
Presione [ REC
I
] repetidamente hasta que aparezca en la pantalla del televisor la longitud deseada de grabación (30 minutos a 6 horas).
Comenzará la grabación a un toque con temporizador.
Ajste Manual de Reloj
ENE / 01 / 2008 ( MAR )
12 : 00 AM
I
0h30m
0h 3 0m
(grabación normal) 1 h00m
6h00m 5h 3 0m
Para cambiar la duración de la grabación durante la grabación a un toque con temporizador:
Presione [ REC
I
] repetidamente hasta que aparezca la duración deseada.
Para cancelar la grabación a un toque con temporizador dentro del tiempo especificado:
Presione [STOP
C
] .
5 Para de tener la grabación presione
[STOP
C
].
ES 105
E9M81UD_ZV457MG9.indd 105 2008/05/15 14:32:15
ESPAÑOL
Grabación con Temporizador
Usted puede programar el equipo para que grabe hasta 12 programas, con un mes de anticipación. También hay disponibles grabaciones de programas diarias o semanales.
Antes de grabar, asegúrese de que
• Antes de establecer una programación del temporizador configure el reloj.
• Inserte un disco grabable con suficiente espacio libre o una cinta de cassette con una lengüeta de grabación.
1
2
Presione [TIMER].
Utilice [
K
/
L
] para seleccionar “Prog. nuevo”, y luego presione [OK].
Programaci. con Reloj
MAR ENE/01 11:00AM
Fcha Empieza Termina
Prog. nuevo
CH
STANDBY-ON
SOURCE DTV/TV DISPLAY OPEN/CLOSE
A
.@/:
1
GHI
4
PQRS
7
.
DISC MENU
TUV
8
SPACE
0
ABC
2
JKL
5
DEF
3
MNO
6
WXYZ
9
CLEAR s
TITLE j
F
-h g
CHANNEL
+
C
REC MODE VCR DVD
REC
I
SEARCH
5
HDMI
B
B
RETURN
4
AUDIO
RAPID PLAY
1
3
4
5
Configure una programación del temporizador.
Presione [OK].
Presione [TIMER SET] para configurar una programación del temporizador.
Aparecerá
en el pantalla del panel frontal.
Configure la fecha.
o
Fcha
ENE/02
CH
DTV125. 1
Empieza
- - : - -
GRAB a
DVD
Termina
- - : - -
Modo
SP
SP 2h00m p
B
Configure las horas de inicio y finalización.
o
Fcha
ENE/02
CH
DTV125. 1
Empieza
12 : 00AM
GRAB a
DVD
Termina
- - : - -
Modo
SP s p
B
SP 2h00m
B
Seleccione un modo deseado de entrada y el canal a grabar.
Para obtener más detalles, consulte “How to select a channel number for the timer recording” en la página
44 del manual del usuario.
ej.) modo digital o
Fcha
ENE/02
CH
DTV125. 1
Empieza
12 : 00AM
GRAB a
DVD
Termina
1 : 00AM
Modo
SP s p
B
B
SP 1h00m
Seleccione un medio de grabación (“DVD” o “VCR”).
o Fcha
ENE/02
CH
DTV125. 1
Empieza
12 : 00AM
GRAB a
DVD
Termina
1 : 00AM
Modo
SP
SP 1h00m p
B
Seleccione un modo de grabación.
o
Fcha
ENE/02
CH
DTV125. 1
Empieza
12 : 00AM
GRAB a
DVD
Termina
1 : 00AM
Modo
SP
SP 1h00m p
Reproducción
1 Presione
[DVD].
DVD
2 Abra la bandeja de discos, y Inserte un disco.
OPEN/CLOSE
A
3 Cerrar la bandeja de discos.
OPEN/CLOSE
A
4 Comience a reproducir.
B
5 Detenga la reproducción.
C
106 ES
E9M81UD_ZV457MG9.indd 106 2008/05/15 14:32:16
MEMO
E9M81UD_ZV457MG9.indd 107
ES 107
2008/05/15 14:32:21
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Certain parts are excluded from this warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.
Note: Any product so l d and identified as refurbished or renewed carries a ninety ( 9 0) days l abor and parts l imited warranty.
LIMITS AND E
X
CLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER
PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN SERVICE
UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This limited warranty does not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occur during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or products not supplied by FUNAI CORP., or damage, which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product, or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS
PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL
OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF
OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT
PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI
CORP. will not reimburse you for any service done by unauthorized service providers without prior written approval.
To l ocate your nearest AUTHORIZED SERVICE CENTER or for genera l service inquiries, p l ease contact us at:
FUNAI SERVICE CORPORATION
Te
l
: 1-
8
00-
6
05-
86
10 www.magnavox.com
/
support
2200 Spiegel Drive Groveport, OH 43125
E9M81UD
1VMN25873
★★★
Printed in China
* 1 V M N 2 5 8 7 3 *
E9M81UD̲ZV457MG9̲EN̲v3.indd 108 2011/09/14 14:33:49
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 9 Symbols Used in this Owner’s Manual
- 10 Front Panel
- 11 Rear Panel
- 12 Remote Control
- 14 Front Panel Display
- 22 Guide to On-Screen Display / Menu
- 24 Main Menu
- 25 Switching DVD / VCR Mode
- 25 How to Insert a Disc / Cassette Tape
- 27 Auto Channel Scan
- 28 Adding / Deleting Channels
- 30 Auto Clock Setting
- 31 Manual Clock Setting
- 31 Daylight Saving Time
- 32 Switching Analog Mode / Digital Mode
- 32 Channel Selection
- 33 Selecting TV Audio
- 35 DTV Closed Caption
- 36 Closed Caption Style
- 39 Make Recording Compatible
- 39 Setting for Auto Chapter
- 39 Recording the DTV Closed Caption
- 39 Recording from a Cable Box or Satellite
- 45 Hints for Timer Recording
- 46 Overwriting from the Beginning of the Title
- 46 Overwriting in the Middle of the Title
- 47 Hints for Overwriting
- 48 Connection to an External Device
- 49 Recording from an External Device
- 53 Finalizing a Disc