Installing the Washing Machine. Samsung F1245A, B1445AV, B1445, B1445A, B1445A(V/S/C), F1245AV, R1045AV, R1245A, F1045AV, R1245AV
Add to My manuals
176 Pages
advertisement
Installing the Washing Machine
Unpacking the Washing Machine
Unpack your washing machine and inspect it for shipping damage. Also make sure that you have received all of the items shown below. If the washing machine was damaged during shipping or you do not have all of the items, contact your Samsung dealer immediately.
Overview of the washing machine
Worktop
Control panel
Detergent drawer
Door
Drain Hose
Plug
Base cover
Adjustable feet
Wrench
Drain hose
Hose guide
2
SAMSUNG
Washing Machine Owner
’ s Instructions
Debris filter
Emergency drain tube
Filter-cover
Cold Water supply hose
Bolt hole covers
Installing the Washing Machine
Selecting a location
Before you install the washing machine, select a location with the following characteristics:
•
A hard, level surface (if the surface is uneven, see "Adjusting the leveling feet," below)
•
Away from direct sunlight.
•
Adequate ventilation
•
Room temperature that will not fall below 0 ˚C
•
Away from sources of heat such as coal or gas
Make sure that the washing machine does not stand on its power cord.
Ventilation openings must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
Adjusting the leveling feet
If the floor is uneven, adjust the feet (do not insert pieces of wood or any other objects under the feet):
1.
Loosen the leg bolt by turning it with your hand until it is at the desired height.
2.
Tighten the locking nut by turning it with the supplied wrench.
•
Place the washer on a sturdy, flat surface.
If the washer is placed on an uneven or weak surface, noise or vibration occurs.
(Only a l degrees angle is allowed.)
Removing the shipping bolts
Before using the washing machine, you must remove the five shipping bolts from the back of the unit. To remove the bolts:
2
1
3
1.
Loosen all bolts with the supplied wrench before removing them.
2.
Take each bolt head and pull it through the wide part of the hole.
Repeat for each bolt.
3.
Fill the holes with the supplied plastic covers.
4.
Keep the shipping bolts for future use.
Connecting the water supply hose(Option)
1. Remove the adaptor from the water supply hose.
2. First, using a “+” type screw driver, loosen the four screws on the adaptor. Next, take the adaptor and turn part(b) following the arrow until there is a 5mm gap.
3. Connect adaptor to the water tap by tightening the screws firmly.
Then, turn part (b) following the arrow and put(a) and (b) together.
a b c
4.Connect the water supply hose to the adaptor.
Pull down part (c) of the water supply hose.
When you release part (c) the hose automatically connects to the adaptor making a ’click’ sound.
5. Connect the other end of the water supply hose to the inlet water valve at the top of the washer.
Screw the hose clockwise all the way in.
•
If the water tap has a screw type faucet, connect the water supply hose to the tap as shown.
NOTICE
After completing connection, if water leaks from the hose, then repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.
SAMSUNG
Washing Machine Owner
’ s Instructions
3
Installing the Washing Machine
Connecting the water supply hose
The water supply hose must be connected to the washing machine at one end and to the water faucet at the other. Do not stretch the water supply hose. If the hose is too short and you do not wish to move the water faucet, replace the hose with a longer, high pressure hose.
To connect the water supply hose:
1.
Take the L-shaped arm fitting for the cold water supply hose and connect to the cold water supply intake on the back of the machine. Tighten by hand.
2.
Connect the other end of the cold water supply hose to your sink's cold water faucet and tighten it by hand. If necessary, you can reposition the water supply hose at the washing machine end by loosening the fitting, rotating the hose, and retightening the fitting.
Option: 1. Take the red L-shaped arm fitting for the hot water supply hose and connect to the red hot water supply intake on the back of the machine. Tighten by hand.
2. Connect the other end of the hot water supply hose to your sink's hot water faucet and tighten it by hand.
3. Use a Y-piece if you only want to use cold water.
Note:
The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be used.
Positioning the drain hose
The end of the drain hose may be positioned in three ways:
Over the edge of a sink
The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving.
ln a sink drain pipe branch
The drain pipe branch must be above the sink siphon so that the end of the hose is at least
60 cm above the ground.
ln a drain pipe
Samsung recommends that you use a 65 cm high vertical pipe; it must be no shorter than 60 cm and no longer than 90 cm.
4
SAMSUNG
Washing Machine Owner
’ s Instructions
Installing the Washing Machine
Plugging in the machine
For European Users.
You will
NOT
need to ground the plug of the washing machine.
For U.S. Users.
You
MUST
ground the plug of the washing machine.
Check with a licensed electrician before using the machine to make sure it is properly grounded.
For U.K. Users.
Wiring lnstructions
WARNING THIS APPLIANCE MUST BE EARTHED.
This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of electric shock providing an escape wire for the electric current.
The appliance is equipped with a mains lead which includes an earth wire for connecting to the earth terminal of your mains plug.
The plug must be plugged into a socket that is properly installed and earthed.
GREEN AND
YELLOW
*The wires in this mains lead are coloured in accordance with the following code:
•
Green and yellow
•
Blue
•
Brown
: Earth
: Neutral
: Live
•
AS the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings indentifying the terminals in your plug, proceed as follows.
•
Connect the green and yellow wire to the terminal in the plug marked with the letter E or the earth symbol ( ) or coloured green or green-andyellow.
•
Connect the blue wire to the terminal marked with the letter N or coloured black.
•
Connect the brown wire to the terminal marked with the letter L or coloured red.
* Consult a qualified electrician or service technician if in doubt about any of these instructions.
The manufacturer of this washing machine will not accept any liability for damage to persons or material for non observance of these requirements.
There are no user serviceable parts inside the washing machine and if the mains lead of this appliance is damaged, it must only be replaced by qualified service personnel approved by the manufacturer because special tools are required.
BLUE
13 AMP
FUSE
BROWN
WARNING
Ensure that the plug and power cord are not damaged before use. If you have any reason to remove the moulded plug from this appliance, immediately remove the fuse and dispose of the plug.
Do not connect the plug to a mains socket under any circumstances as there is a danger of electric shock.
CIRCUITS
Your washing machine should be operated on a separate circuit from other appliances. Failure to do this may cause the circuit breaker to trip or the fuse to blow.
SAMSUNG
Washing Machine Owner
’ s Instructions
5
advertisement
Key Features
- Freestanding Front-load 6 kg 1400 RPM White
- Hygiene/anti-allergy, Black
- 54 L
Related manuals
advertisement
Table of contents
- 2 Safety Precautions
- 2 Before using the appliance
- 2 Safety instructions
- 3 Table of Contents
- 4 Installing the Washing Machine
- 4 Unpacking the Washing Machine
- 4 Overview of the washing machine
- 5 Selecting a location
- 5 Adjusting the leveling feet
- 5 Removing the shipping bolts
- 5 Connecting the water supply hose(Option)
- 6 Connecting the water supply hose
- 6 Positioning the drain hose
- 7 Plugging in the machine
- 8 Washing a Load of Laundry
- 8 Overview of the control panel
- 10 Washing for the first time
- 10 Putting detergent in the washing machine
- 11 Washing clothes using Fuzzy Logic
- 12 Washing clothes manually
- 12 Using Delay Start
- 13 Washing tips and hints
- 14 Maintaining the Washing Machine
- 14 Draining the washing machine in an emergency
- 14 Repairing a frozen washing machine
- 14 Cleaning the exterior
- 15 Cleaning the detergent drawer and recess
- 15 Cleaning the debris filter
- 16 Cleaning the water hose mesh filter
- 17 Troubleshooting
- 20 Appendix
- 21 Specification