advertisement
Control guide
Main unit
[8, POWER]
Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.
Standby indicator [^]
When the unit is connected to the AC mains supply, this indicator lights up in standby mode and goes out when the unit is turned on.
[SPEAKERS, A, B]
For selecting speakers A or B.
Turning the speakers off automatically engages the
STEREO/2CH MIX mode (when listening through headphones, for example).
[MULTI CONTROL, CANCEL]
Press to enter Multi control or cancel.
[ENTER]
Enters setting in Multi control.
[INPUT SELECTOR]
For selecting input.
Selects each setting in Multi control.
[VOLUME]
Volume control.
POWER
SPEAKERS
A B DUAL AMP
BI-AMP BAND PRESET TUNE
MULTI
CONTROL ENTER
INPUT SELECTOR
CANCEL
DOWN
VOLUME
UP PHONES
VCR 2
VIDEO IN L AUDIO IN R
Remote control signal sensor
[VCR 2]
For a game player, etc.
Display indicators
[RE-MASTER]
Lights when the multi-source re-master function is on.
[MULTI CONTROL]
When you press the [MULTI
CONTROL, CANCEL] button and enter the settings the indicator lights.
[SLEEP]
Sleep timer indicator.
[DUAL AMP]
Lights when the
DUAL AMP function is activated.
[BI-AMP]
Lights when the BI-
AMP function is activated.
[BAND]
For switching between FM and AM.
[PRESET]
Press to allow preset station selection with [2 TUNE 1].
[2 TUNE 1]
For tuning the radio and selecting preset stations.
Press and hold until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found.
[TUNED]
A station is tuned.
[ST]
A stereo FM broadcast is tuned.
[MONO]
Lights when using the monaural mode.
[
M
]
Flashes during automatic presetting.
[PHONES]
Headphone jack.
Plug type: 6.3 mm (1/4") stereo
Avoid listening for prolonged periods of time to prevent hearing damage.
Turn the speakers off when using the headphones.
[DIGITAL INPUT]
• The channels contained in the digital input signal light.
• No sound is output from a channel if the speaker is set to “ _” (not connected) in
“Speakers combination settings” (ápage 12) even if the channel indicator lights.
L: Front left channel C: Center channel
R: Front right channel
SB: Surround back channel
LS: Surround left channel
RS: Surround right channel
S: If the surround channel is monaural
LFE (Low Frequency Effects): Deep-bass effect
[PCM]
Lights when the PCM FIX mode is set.
RE-MASTER
MULTI CONTROL
SLEEP
SPEAKERS
A B BI-WIRE
TUNED ST MONO
M
2CH
MIX kHz
MHz
DIGITAL INPUT
L
LS
PCM
C R
SB RS
S LFE
SOUND MODE
DTS
DIGITAL
-ES
EX
DTS 96/24
EX
PL
NEO:6 SFC x STEREO
16
[– SPEAKERS –
Speaker indicators.
A
,
B
,
BI-WIRE
]
A:
B:
Sound is output from speakers connected to the front A, surround, and center terminals.
Sound is output only from speakers connected to the front B terminals.
A, B: Sound is output from speakers connected to the front A, B, surround, and center terminals.
A, B, BI-WIRE: Sound is output from speakers connected by Bi-wiring.
General display
Shows the input mode, radio frequency, and other general information.
[2CH MIX]
Lights when playing a multi-channel source in
2CH MIX mode.
[kHz, MHz]
Frequency unit indicators.
kHz:
AM, or PCM sampling frequency
MHz:
FM
[SOUND MODE]
The following light to indicate the source’s input signal (multichannel digital signal) and the decoding format used. (ábelow)
•
•
SOUND MODE
DIGITAL:
DIGITAL EX:
EX:
DTS-ES:
DTS:
DTS 96/24:
STEREO:
Dolby Digital decoder is being used.
Dolby Digital Surround EX decoder (Dolby Pro Logic decoder) is being used when the input signal is Dolby Digital 5.1-channel or Dolby Digital Surround EX.
Dolby Digital Surround EX decoder (Dolby Pro Logic decoder) is being used when the input signal is DTS.
DTS-ES discrete or matrix decoder is being used.
DTS decoder is being used.
DTS 96/24 decoder is being used.
2-channel stereo decoder is being used.
NEO:6:
SFC:
PL
PL :
:
Dolby Pro Logic decoder is being used.
Dolby Pro Logic decoder is being used.
DTS NEO:6 matrix decoder is being used.
SFC matrix function is being used.
DIGITAL EX and EX are displayed only when “1 SPKR ” is selected in “Surround back speaker settings”. (ápage 12)
PL is displayed when using Dolby Pro Logic with stereo (2-channel) sources and “ SB ” is set to “_” in “Speakers combination settings”. (ápage 12)
Remote control
Buttons not explained on this page are used only to operate other equipment.
á
Refer to the separate booklet, “Remote Control Operation Guide”, for remote control operation details.
[^, RECEIVER]
Standby/on button.
[CD, VCR, TUNER –BAND, TV,
DVD RECORDER,
DVD PLAYER
–
ANALOG 6CH]
Input mode and remote control mode buttons.
[1, 2, 3, 4, 5, 6, 7, 8, 9, 0]
To enter radio frequencies and channels.
[DISC, DIRECT TUNING]
To enable selection of radio stations by frequency.
[ ≧ 10, ENTER]
To enter two digit channels.
[1, CH, 2]
For selecting preset radio channels.
[4, 3, VOLUME]
To adjust the volume.
[MULTI-SOURCE RE-MASTER]
For selecting a re-master mode.
[DIMMER]
For dimming the unit’s display.
[ PL ]
Select MOVIE (DOLBY EX), MUSIC or
GAME when Dolby Pro Logic mode or
Dolby Pro Logic mode is on.
[DTS NEO:6]
For selecting a DTS NEO:6 mode:
CINEMA or MUSIC.
[SFC, MUSIC]
For selecting a SFC mode:
LIVE, POP/ROCK, VOCAL, JAZZ or DANCE.
[SFC, AV/MOVIE]
For selecting a SFC mode:
DRAMA, ACTION, SPORTS, MUSICAL or
GAME.
[OFF]
To cancel surround effects.
[SUBWOOFER]
For selecting subwoofer level.
[MUTING]
To mute the volume.
[TEST]
To start the speaker test signal.
[LEVEL]
To adjust speaker level.
[EFFECT]
To adjust Dolby Pro Logic , DTS NEO:6 or SFC effects.
[w, 3, q, 4]
First select EFFECT, LEVEL or SFC, and then press [w, 3] or [q, 4] to complete the setting.
Limitations on using surround effects
(
á page 15
)
Depending on the speaker settings and input signal (audio signal recorded on the disc etc.), some surround effects cannot be used.
Speaker settings Input signal
Only front L/R
Front L/R + Center
+
All
+
Multi-channel
Surround effects that cannot be used
• Dolby Pro Logic
• SFC
• Dolby Pro Logic
• SFC
• DTS NEO:6
• DTS NEO:6
Front L/R + Center
+
2-channel • GAME mode (Dolby Pro Logic )
No surround back
+
Multi-channel • Dolby Pro Logic • DTS NEO:6
Input signal (
( ) are display indicators ápage 16
)
• 1-channel (
C
)
• Surround sound is monaural (
Excluding 2-channel sources
S
)
• 3-channel (
L C R
)
• PCM with a sampling frequency exceeding 96 kHz
• DTS-ES • DTS 96/24-ES
Surround effects that cannot be used
• Dolby Pro Logic
• SFC
• DTS NEO:6
• Dolby Pro Logic • DTS NEO:6
17
Sound quality/Sound field/Convenient functions
POWER
SPEAKERS
A B DUAL AMP BI-AMP BAND PRESET TUNE
VCR 2
VIDEO IN L AUDIO IN R
MULTI
CONTROL ENTER
INPUT SELECTOR
CANCEL
MULTI
CONTROL ENTER
INPUT SELECTOR
CANCEL
DOWN
VOLUME
UP PHONES
Adjusting the level of each surround effect
á
Refer to page 15 for information about surround effects.
Using Dolby Pro Logic
You can adjust the effect of “ MUSIC ” with “DIMEN ”
(Dimension Control), “
C-WDTH ” (Center Width Control) and
“ PANORAMA ”. (Only when the input signal is 2-channel.)
DIMEN (Dimension Control)
You can make up for differences in the output level of the front and surround speakers. You can choose a level between –3 and +3 -
Increase the level to move sound to the front speakers, decrease to move it to the surround speakers.
Select.
Adjust.
Factory setting: 0
DIMEN 0
C-WDTH (Center Width Control)
This adjustment helps you realize a more natural sound image when listening to music. Move sound out into the front speakers to improve the overall front image, or add sound to the center speaker to fix the center image. You can choose a level between
0 (the center speaker is dominant) and 7 (center sound is spread out).
Select.
Adjust.
18
Basic operations with the MULTI CONTROL
INPUT SELECTOR
Turn to change.
ENTER
Press to enter.
MULTI
CONTROL
CANCEL n
To return to the previous setting/To cancel
Press.
n
To select another settings
Press several times to return to step 2 in the operations across and select another setting.
n
To finish settings
Press several times to select “EXIT ” and press [ENTER].
á
Page 24 “Multi control menus and factory settings”.
C-WDTH 3
Factory setting: 3
PANORAMA
Sound is spread out more so you feel like you are surrounded by music.
Select.
Select.
PANORAMA
: Factory setting
Using DTS NEO:6
You can adjust the effect of “
MUSIC ” with the center image control.
C-IMG (Center Image Control)
This adjustment helps you realize a more natural sound image when listening to music. Move sound out into the front speakers to improve the overall front image, or add sound to the center speaker to fix the center image. You can choose a level between
0 (the center speaker is dominant) and 5 (center sound is spread out).
Select.
Adjust.
C-IMG 2
Factory setting: 2
Using the Sound Field Control (SFC)
You can adjust the sound field by adjusting the level of the speakers and effect. These adjustments can be made for each SFC mode.
To adjust the speaker level
Select.
Adjust.
Factory settings: 0 dB
Factory setting: 10
• Speakers set as “
_” (not connected) in “Speakers combination settings” are skipped. (ápage 12)
To adjust SFC effect
Select.
Adjust.
Factory setting: 5
Use the MULTI CONTROL menus to change the settings.
(ápage 18 “Basic operations with the MULTI CONTROL”)
1
MULTI
CONTROL
Enter the MULTI CONTROL.
CANCEL
Select the settings to change.
(ábelow, right)
Adjusting the tone
You can adjust the level of the bass and treble.
2
Select “TONE ” and press [ENTER].
3
Select “BASS ” or “TREBLE ” and press [ENTER].
4
Adjust the level and press [ENTER].
BASS,
TREBLE
(MIN) (MAX)
5
Select another setting
Finish setting
Adjusting the volume balance
You can adjust the balance of the front speakers.
2
Select “BALANCE ” and press [ENTER].
3
Adjust the balance and press
[ENTER].
L R
• The bar shows the standard balance.
4
Select another setting
Finish setting
Adjusting the brightness of the display
Dim the display for better viewing in a darkened room.
Choose a level between 1 (bright) and 3 (dim).
2
Select “DIMMER ” and press [ENTER].
3
Select “ON ” and press [ENTER].
• Select “
OFF ” to cancel.
OFF, ON
4
Select the level and press [ENTER].
LEVEL 1,
LEVEL 2,
LEVEL 3
5
Select another setting
Finish setting
• When you operate the main unit or remote control, this is temporarily canceled.
Sleep timer
The sleep timer can turn the unit off after a set time.
It does not control any other components.
2
Select “SLEEP ” and press [ENTER].
3
Select the time and press [ENTER].
When this is set, “ SLEEP” appears on the display.
• To cancel, select “ OFF ”.
OFF, 30, 60,
90, 120
(in minutes)
4
Select another setting
Finish setting
• To check the setting:
After setting the time, you can check the remaining time using step 2.
• To change a setting:
Repeat the procedure from the beginning.
Changing the audio output (Dual program)
When the input signal is Dolby Digital, DTS and “
DUAL ” appears in the display, the audio to be output is set.
2
Select “OPTION ” and press [ENTER].
3
Select “DUAL PRG ” (DUAL PROGRAM) and press [ENTER].
4
Select the audio and press [ENTER].
MAIN: Main audio output
SAP: Sub channel audio output
MAIN+SAP: Main and sub channel audio output
5
Select another setting
Finish setting
• The setting remains in effect even if the power is turned off.
Listening comfortably at low volume
Change this setting to listen to software recorded with Dolby Digital at low volume (such as late at night) maintaining audio clarity. It reduces the peak level in loud scenes without affecting the sound field.
2
Select “OPTION ” and press [ENTER].
3
Select “DR COMP ” (DYNAMIC RANGE
COMPRESSION) and press [ENTER].
4
Select the level and press [ENTER].
OFF: The software is played with the original dynamic range.
STANDARD: The level recommended by the producer of
MAX: the software for household viewing.
The maximum allowable compression
(recommended for night viewing).
5
Select another setting
Finish setting
A/D attenuator
Turn the A/D attenuator on if “
OVERFLOW ” lights frequently when using 2-channel analog input or DVD ANALOG 6CH input.
2
Select “OPTION ” and press [ENTER].
3
Select “A/D ATT ” (A/D ATTENUATOR) and press
[ENTER].
4
Select “ON ” and press [ENTER].
• To cancel, select “ OFF ”.
OFF,
ON
5
Select another setting
Finish setting
The RESET function
The operation settings for the unit will be initialized to the settings made at the time of shipment.
However, any preset radio stations will not be erased.
2
Select “OPTION ” and press [ENTER].
3
Select “RESET ” and press [ENTER].
4
Select “YES ” and press [ENTER].
• To cancel, select “ NO ”.
• When you select “ YES ”, the input source becomes
“ TUNER ” (Preset Channel 1).
NO,
YES
19
Sound quality/Sound field/Convenient functions
Adjusting the subwoofer level
You can adjust the volume of the subwoofer while listening to a source.
Sound can be distorted if you raise the volume while the subwoofer level is high. Reduce the subwoofer level if this occurs.
Muting
To mute the volume.
Multi-source re-master
This original feature boosts the frequencies of the higher harmonics that are lost during recording due to compression.
You can enjoy a full, more natural sound with this.
Select.
Select.
• You can make fine settings by pressing [TEST] then adjusting the output level. (ápage 13)
• You cannot adjust the subwoofer level if “DVD ANALOG 6CH” is selected.
• Select “ SW --- ” to stop output.
Factory setting: SW 10
• “ MUTING IS ON ” scrolls on the display while the volume is muted.
• Muting is canceled when the power is turned off.
n
To cancel: Press again
EFFECT 1: For fast tracks (pop and rock)
EFFECT 2: For tracks with a variety of tempos (jazz)
EFFECT 3: For slow tracks (classical)
EFFECT 4: For compressed audio signals
OFF: The re-master processing is off (factory setting)
Dimmer
Dim the display for better viewing in a darkened room.
• Dolby Pro Logic , DTS NEO:6 and SFC are canceled when using multi-source re-master.
• If you make any settings in “Speakers combination settings”, “Surround back speaker settings” or “Speaker settings” (ápages 12, 21) when using multi-source re-master, multisource re-master is canceled.
Multi-source re-master cannot be used in the following cases.
• When input signal is DTS 96/24, PCM with sampling frequencies of 192, 176.4, 96 or 88.2 kHz.
n
To cancel: Press again
á
Refer to page 19 for adjusting the brightness of the display.
Making a recording
You can record to a tape deck connected to TAPE REC (OUT) or a DVD recorder connected to DVD RECORDER OUT.
See the recording unit’s operating instructions for details on how to prepare it for recording.
INPUT SELECTOR
1
Select the source to be recorded.
INPUT SELECTOR
20
POWER
SPEAKERS
A B DUAL AMP BI-AMP BAND PRESET TUNE
VCR 2
VIDEO IN L AUDIO IN R
MULTI
CONTROL ENTER
INPUT SELECTOR
CANCEL
DOWN
VOLUME
UP PHONES
2
Begin recording.
Follow your recording unit’s operating instructions.
3
Start the source to be recorded.
Follow your equipment’s operating instructions.
Note
• You cannot record a source connected through a digital terminal.
• When recording from a TV/STB, DVR, CD or DVD ensure the source is connected through the corresponding analog terminals and “ ANALOG ” input is selected. (ápages 4, 5, 9, 10 and 13)
• With a tape deck, you can record any analog source except TAPE.
• With a DVD recorder, you can record any analog source except DVR.
• When you select DVD ANALOG 6CH mode, only sound from the front left and right channels is recorded.
Receiver settings - Advanced
POWER
A
SPEAKERS
B DUAL AMP BI-AMP BAND PRESET TUNE
VCR 2
VIDEO IN L AUDIO IN R
MULTI
CONTROL ENTER
INPUT SELECTOR
CANCEL
MULTI
CONTROL ENTER
INPUT SELECTOR
CANCEL
DOWN
VOLUME
UP PHONES
Basic operations with the MULTI CONTROL
INPUT SELECTOR
Turn to change.
ENTER
Press to enter.
MULTI
CONTROL
CANCEL n
To return to the previous setting/To cancel
Press.
n
To select another settings
Press several times to return to step 2 in the operations across and select another setting.
n
To finish settings
Press several times to select “EXIT ” and press [ENTER].
• Any changes to settings remain as set even if the power is turned off.
á
Page 24 “Multi control menus and factory settings”.
Use the MULTI CONTROL menus to change the settings.
1
MULTI
CONTROL
Enter the MULTI CONTROL.
CANCEL
INPUT SELECTOR
Select “SETUP 2 ”
(“
ADVANCE SETUP ” scrolls once)
and press [ENTER].
Select the settings to change. (ábelow, right)
Speaker settings
Set the size so that the speakers can adequately reproduce the bass range.
2
Select “SPEAKERS ” and press [ENTER].
3
Select the speaker and press [ENTER].
SUB-WFR, FRONT, CENTER, SURROUND, SUR BACK
4
Change the setting and press [ENTER].
SUB-WFR: NO, YES FRONT: SMALL, LARGE
CENTER/SURROUND: NONE, SMALL, LARGE
SUR BACK: NONE, 1 SPKR, 2 SPKRS
NONE: For speakers you haven’t connected (center, surround or surround back).
SMALL: For speakers that cannot adequately reproduce the bass range. This setting is sufficient for most speakers if you are using a subwoofer.
LARGE:
For speakers that can reproduce a full sound range, particularly the bass range below 80 Hz.
1 SPKR: If you connect one surround back speaker.
2 SPKRS: If you connect two surround back speakers.
For the subwoofer (SUB-WFR), select “
YES ” if you have connected one, or “ NO ” if you have not.
Repeat steps 3 and 4 for each speaker channel.
5
Select another setting
Finish setting
The following are set automatically.
• When you set “
FRONT ” to “SMALL ”, “SUB-WFR ” is set to “YES ”.
• When you set “ SUB-WFR ” to “NO ”, “FRONT ” is set to “LARGE ”.
Distance setting
By setting the distance between the speaker’s position (except the subwoofer) and the listener’s seating position, the sound delay time is automatically adjusted so that sound reaches the listener at the same time.
2
Select “DISTANCE ” and press [ENTER].
3
Select the speaker and press
[ENTER].
FRONT,
CENTER,
SURROUND,
SUR BACK
4
Set the distance and press
[ENTER].
You can select differences at one foot intervals.
5
Select another setting
Finish setting
(MIN) (MAX)
Filter setting
If the Front speakers are set to “ SMALL ”, make this setting.
Change the cut-off if the bass from the front speakers is unsatisfactory so that this bass is output through the subwoofer.
2
Select “FILTER ” and press [ENTER].
3
Select the bass filter frequency and press [ENTER].
• This setting is effective for all speakers set to
“ SMALL ” in “Speaker settings”.
4
Select another setting
Finish setting
80, 100, 150,
200 (Hz)
Bi-amp setting
This is displayed when you set “ BI-WIRE ” in “Bi-wiring settings”. Select this when you connect bi-wire compatible front speakers.
You can adjust HF (high frequency) and LF (low frequency) output balance from the bi-wired speakers. You can also adjust the sound delay time to offset the difference in HF and LF output directions.
2
Select “BI-AMP ” and press [ENTER].
Adjusting the balance
3
Select “BALANCE ” and press [ENTER].
4
Adjust the balance and press [ENTER].
L H
• The bar shows the standard balance.
Correcting the HF and LF difference
3
Select “HF PHASE ” and press [ENTER].
4
Set the difference and press [ENTER].
HF
LF
Difference
(Side view of a speaker in cross section)
0.00 FEET
(MIN) (MAX)
5
Select another setting
Finish setting
You can select differences at
0.03 feet intervals.
21
The radio
BAND PRESET TUNE
POWER A
SPEAKERS
B DUAL AMP BI-AMP BAND PRESET TUNE
VCR 2
VIDEO IN L AUDIO IN R
MULTI
CONTROL ENTER
INPUT SELECTOR
CANCEL
MULTI
CONTROL ENTER
CANCEL
INPUT SELECTOR
DOWN
VOLUME
UP PHONES
Manual Tuning
n
On the remote control (Direct tuning)
1
Select “TUNER ”.
2
Select “FM ” or “AM ”.
Press and hold for 2 seconds.
3
Press [DISC, DIRECT TUNING].
4
Enter the station frequency.
Basic operations with the MULTI CONTROL
INPUT SELECTOR
Turn to change.
ENTER
Press to enter.
MULTI
CONTROL n
To return to the previous setting/To cancel
Press.
CANCEL
á
Page 24 “Multi control menus and factory settings”. e.g. 107.9 MHz, Press [1] → [0] → [7] → [9]
Tuning intervals: FM - 0.1 MHz,
AM - 10 kHz
• If you do not press a button while the cursor is flashing, the display returns to the frequency being received.
• If the frequency has not been input correctly, “ ERROR ” will be displayed.
n
On the main unit
1
Select “TUNER ”.
INPUT SELECTOR
2
Select “FM ” or “AM ”.
BAND
3
Tune to the station.
TUNE
Tuning intervals: FM - 0.2 MHz,
AM - 10 kHz
• Automatic tuning
Hold down [TUNE 2 or 1] until the frequency begins to scroll.
Tuning stops when a station is found. (Tuning may stop if there is interference.)
22
For your reference
Improving reception
DVD players can interfere with radio reception. Turn the DVD player off or move it further away from the AM loop antenna if this occurs.
Preset tuning
Presetting stations
n
Auto presetting
1
Set the channel reception to FM 87.9 MHz or AM
530 kHz.
Preset channels that are automatically assigned by this unit are:
FM: 1 to 30
Preset the FM stations first. If the AM stations are preset before the
FM stations, they will be erased when the FM stations are preset.
2
MULTI
CONTROL
Enter the MULTI CONTROL.
(ápage 22 “Basic operations with the MULTI CONTROL”)
CANCEL
3
Select “TUNER ” and press [ENTER].
4
Select “AUTO MEM ” (AUTO MEMORY) and press [ENTER].
5
Select “START ” and press [ENTER].
• Select “ CANCEL ” to cancel.
START,
CANCEL
• During automatic presetting, the memory indicator (
M
) flashes and the frequency scrolls. The memory indicator and channel numbers are displayed for a second when a station is preset.
• The last station to be preset is displayed when presetting finishes.
• Frequencies may not preset correctly when broadcast waves are too strong or too weak. In such cases, carry out presetting manually.
Listening to preset stations
n
On the remote control
• Select the channel
n
Manual presetting
1
Tune to the station you want to preset.
(ápage 22)
2
MULTI
CONTROL
Enter the MULTI CONTROL.
(ápage 22 “Basic operations with the MULTI CONTROL”)
CANCEL
3
Select “TUNER ” and press [ENTER].
4
Select “MEMORY ” and press [ENTER].
5
Select a channel number and press [ENTER].
“ STORED ” is displayed.
• To continue presetting, press [TUNE 2 or 1] to tune another station from step 1.
6
Press [MULTI CONTROL, CANCEL] 2 times to select “EXIT ” and press [ENTER].
• Even if the AC power supply cord is disconnected from the household AC outlet, the stations remain in the memory for approximately two weeks.
• FM stations can also be preset in the MONO mode. (ábelow) n
On the main unit
1
Press.
• Press the numbered buttons to select the channel
2
Select the channel.
After 5 seconds, the display will change from the channel number to the frequency.
• Hold down the button to change channels faster.
To select a two digit number e.g. 21: [ ≧ 10, ENTER] → [2] → [1]
Reducing excessive noise
Select if noise is excessive during radio reception.
Preparation: Enter the MULTI CONTROL.
(ápage 22 “Basic operations with the MULTI CONTROL”) n
During FM stereo reception
You can improve FM reception by switching reception to monaural.
1
Select “TUNER ” and press [ENTER].
2
Select “FM MODE ” and press [ENTER].
3
Select “MONO ” and press [ENTER].
• Select “ AUTO ” to cancel.
AUTO,
MONO
4
Press [MULTI CONTROL, CANCEL] 2 times to select
“EXIT ” and press [ENTER].
n
During AM reception
When there is a lot of noise interference with an AM broadcast, try switching to this mode.
1
Select “OPTION ” and press [ENTER].
2
Select “B PROOF ” (BEAT PROOF) and press [ENTER].
3
Select “MODE A ” or “MODE B ” and press [ENTER].
4
Press [MULTI CONTROL, CANCEL] 2 times to select
“EXIT ” and press [ENTER].
23
Remote control mode
Other products may respond to this unit’s remote control. If this happens, change the remote control mode.
Change the remote control mode on the main unit and the remote control.
MULTI
CONTROL ENTER
INPUT SELECTOR
CANCEL
POWER
SPEAKERS
A B DUAL AMP BI-AMP BAND PRESET TUNE
VCR 2
VIDEO IN L AUDIO IN R
MULTI
CONTROL ENTER
INPUT SELECTOR
CANCEL
DOWN
VOLUME
UP PHONES
Basic operations with the MULTI CONTROL
INPUT SELECTOR
Turn to change.
ENTER
Press to enter.
MULTI
CONTROL n
To return to the previous setting/To cancel
Press.
CANCEL
-On the main unit-
1
MULTI
CONTROL
Enter the MULTI CONTROL.
CANCEL
2
Select “SETUP 2 ”
(“ ADVANCE SETUP ” scrolls once )
and press [ENTER].
3
Select “REMOTE ” and press [ENTER].
4
Select “REM2 ” and press [ENTER].
REM1,
REM2
5
Press [MULTI CONTROL, CANCEL] 2 times to select “EXIT ” and press [ENTER].
-On the remote control-
6
Press [TUNER -BAND].
7
Press and hold both at the same time for 2 seconds.
n
To return to REM1
1. Select “
REM1 ” in step 4.
2. Press and hold both [ENTER] and [1] at the same time for 2 seconds in step 7.
Multi control menus and factory settings
Main menu
TUNER
※
1
TONE
Sub menu (factory settings)
FM MODE
※
2
AUTO
MEMORY CH 1
AUTO MEM START
BASS
TREBLE
0 dB
BALANCE
DIMMER
SLEEP
OPTION
OFF
ON
OFF
DUAL PRG
DR COMP
A/D ATT
B PROOF
※
3
RESET
LEVEL 2
MAIN
OFF
OFF
MODE A
YES
Pages
23
19
23
19
24
※
1 During FM/AM reception only ※ 2 During FM reception only
※
3 During AM reception only
※
4 When BI-WIRE is selected only
Main menu
SETUP 1
(BASIC
SETUP)
SETUP 2
(ADVANCE
SETUP)
EXIT
Sub menu (factory settings)
SPKR SET
FRNT L/R
SB SPKR
D-INPUT
IN MODE
SUBW NO
SUBW YES
NORMAL
2 SPKRS
TV/STB
DVR
DVD
CD
TV/STB
DVR
DVD
CD
SUB-WFR
SPEAKERS
DISTANCE
FRONT
CENTER
SURROUND
SUR BACK
FRONT
CENTER
SURROUND
SUR BACK
FILTER 100
BALANCE
BI-AMP
※
4
REMOTE
HF PHASE
REM1
á
Exit the Multi control
LCR S SB
OPT 1
OPT 2
COAX 1
COAX 2
AUTO
YES
SMALL
2 SPKRS
10 FEET
5 FEET
0.00 FEET
Pages
12
13
21 above
–
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 TABLE OF CONTENTS
- 1 BEFORE USE
- 2 IMPORTANT SFETY INSTRUCTIONS
- 3 HOW TO SET UP THE HOME THEATER
- 3 LISTENING CAUTION
- 3 SUPPLIED ACCESSORIES
- 4 HOME THEATER CONNECTIONS
- 4 TV AND DVD PLAYER
- 6 SPEAKERS
- 8 AC POWER SUPPLY CORD
- 9 OTHER CONNECTIONS
- 11 THE REMOTE CONTROL
- 12 RECEIVER SETTINGS - BASIC
- 13 SETTING - TEST
- 14 BASIC OPERATIONS
- 14 PLAYBACK
- 15 USING SURROUND EFFECTS
- 16 OPERATIONS
- 16 CONTROL GUIDE
- 18 SOUND QUALITY/SOUND FIELD/CONVENIENT FUNCTIONS
- 20 MAKING A RECORDING
- 21 RECEIVER SETTINGS - ADVANCED
- 22 THE RADIO
- 24 REMOTE CONTROL MODE
- 24 MULTI CONTROL MENUS AND FACTORY SETTINGS
- 25 REFERENCE
- 25 SPECIFICATIONS
- 25 PRODUCT SERVICE
- 26 WARRANTY (U.S.A.)
- 27 WARRANTY (CANADA)
- 27 MAINTENANCE
- 28 TROUBLESHOOTING GUIDE