advertisement
User Guide CCG-RUMBA • Core
TM
2 Duo 3U CompactPCI
®
CPU Board
Bus
Number
0
0
0
3
2)
Device
Number
31
31
31
0
Function
Number
2
3
6
0
Vendor ID
0x8086
0x8086
0x8086
0x8086
Device ID
0x2828
0x2829
0x282A
0x283E
0x284F
0x109A
Description
SATA: Non-AHCI/RAID
1)
SATA: AHCI Mode
1)
SATA: RAID 0/1 Mode
SMB Controller
Thermal Controller
1)
Ethernet Controller NC2
1)
Depends on BIOS implementation.
2)
Bus number can vary depending on the PCI enumeration schema implemented in BIOS.
Local SMB Devices
The CCG-RUMBA contains a few devices that are reachable via the System Management Bus (SMBus).
These are the clock generation chip, the SPD EEPROMs on the SO-DIMM memory modules, a general purpose serial EEPROM and a supply voltage and CPU temperature controlling device in particular.
Other devices could be connected to the SMB via the CompactPCI signals IPMB SCL (J1 B17) and IPMB
SDA (J1 C17).
Address
0x58
0xA0
0xA4
0xAE
0xD2
Description
Hardware Monitor/CPU Temperature Sensor (LM87)
SPD of SODIMM1
SPD of SODIMM2
General Purpose EEPROM
Main Clock Generation (CK-505)
© EKF -39- ekf.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 About this Manual
- 4 Edition History
- 4 Legal Disclaimer - Liability Exclusion
- 4 Trade Marks
- 5 Related Documents
- 6 CCG-RUMBA Features
- 6 Feature Summary
- 11 Short Description
- 13 Block Diagram
- 14 Top/Bottom View Component Assembly
- 17 Rear I/O Transition Module CCT-RIO
- 20 Strapping Headers
- 20 Connectors & Sockets
- 20 Front Panel Elements
- 21 Microprocessor
- 21 Thermal Considerations
- 23 Main Memory
- 23 LAN Subsystem
- 24 Serial ATA Interface (SATA)
- 24 Enhanced IDE Interface
- 24 Graphics Subsystem
- 25 Real-Time Clock
- 26 Universal Serial Bus (USB)
- 26 LPC Super-I/O Interface
- 26 SPI Flash
- 27 Reset
- 29 Watchdog
- 30 PG (Power Good) LED
- 30 HD (Hard Disk Activity) LED
- 30 GP (General Purpose) LED
- 31 Hot Swap Detection
- 31 Power Supply Status (DEG#, FAL#)
- 31 PXI Trigger Signals
- 32 Rear I/O Options
- 33 Installing and Replacing Components
- 33 Before You Begin
- 34 Installing the Board
- 35 Removing the Board
- 36 EMC Recommendations
- 37 Installing or Replacing the Memory Modules
- 37 Replacement of the Battery
- 38 Technical Reference
- 38 Local PCI Devices
- 39 Local SMB Devices
- 40 Hardware Monitor LM
- 41 GPIO Usage
- 41 GPIO Usage ICH
- 43 GPIO Usage SIO
- 44 Configuration Jumpers
- 44 Reset Jumper BIOS CMOS RAM Values (JGP)
- 44 Reset Jumper ICH8 RTC Core (JRTC)
- 45 Connectors
- 45 Front Panel Connectors
- 46 Video Monitor Connector DVI-I
- 47 Video Monitor Connector VGA
- 47 USB Connectors
- 48 Ethernet Connectors
- 49 Internal Connectors
- 58 Expansion Interface Header PEXP
- 59 ATA/IDE Header PIDE
- 60 PCI Express Expansion Header PPCIE
- 61 SDVO Expansion Header PSDVO
- 61 System Reset Header JRST
- 62 PLD Programming Header ISPCON
- 62 Processor Debug Header PITP
- 63 CompactPCI J
- 66 Literature
- 67 Appendix
- 67 Mechanical Drawings
- 68 Mass Storage Considerations
- 73 Coating
- 75 Sample Applications