advertisement
CadJet T-200 Service Manual
NOTE
The rollers should be adjusted moving from the right
side of the Platen to the left side of the Platen.
1. Load a sheet of B-Size paper and adjust Rollers #8, #7, and #6, following the directions in the Adjustment of Pinch Roller
Supports section.
2. Load a sheet of D-Size paper and adjust Rollers #5 and #4, following the directions in the Adjustment of Pinch Roller
Supports section.
3. Load a sheet of E-Size paper and adjust Rollers #3, #2, and #1, following the directions in the Adjustment of Pinch Roller
Supports section.
Mounting Screw Information
1. The torque requirements for the Pinch Roller Support mounting screws is 3 In.-Lbs. ± 0.5.
2. Turning the mounting screw clockwise will tighten the screw.
Turning the mounting screw counterclockwise will loosen the screw.
3. Figure 3-18 shows the Pinch Roller, Pinch Roller Spacer and the mounting screws. You must stand behind the plotter in order to adjust the mounting screws on the Pinch Roller
Supports.
Maintenance 3-25
CadJet T-200 Service Manual
ROLLER
PINCH ROLLER
ASSEMBLY
LEFT MOUNTING
SCREW
Y-ARM
PINCH ROLLER
SPACER
RIGHT MOUNTING
SCREW
ORIENTATION
STANDING BEHIND THE PLOTTER,
FACING THE BACK OF THE PLOTTER
Figure 3-18. Pinch Roller Support and Mounting Screws.
4. If the mounting screw on the right side is loosened (turned counterclockwise), the roller will move to the left. If the mounting screw on the left side is loosened (turned counterclockwise), the roller will move to the right. NEVER
LOOSEN OR TIGHTEN BOTH MOUNTING SCREWS AT
THE SAME TIME ON THE SAME UPPER ROLLER
SUPPORT.
5. If you have loosened one of the mounting screws and the roller has moved, and you need to move the roller in the opposite direction, you must tighten that mounting screw BEFORE loosening the other screw to move the roller in the opposite direction. When tightening the first screw, turn it clockwise with the torque screwdriver until the maximum torque is reached. Then loosen the other screw. AGAIN, NEVER
LOOSEN OR TIGHTEN BOTH MOUNTING SCREWS AT
THE SAME TIME ON THE SAME UPPER ROLLER
SUPPORT.
Maintenance 3-26
CadJet T-200 Service Manual
6. It is extremely important that you maintain downward pressure (towards the floor) on the head of each screw at the same time as you tighten or loosen the screws. Each screw must be completely at the bottom edge of its hole in the back of the Y-Bracket. If this is not done, the Upper Roller
Support will not be perfectly level and will not perform its function properly.
7. Following all of the information in this section precisely will ensure that the Pinch Roller Support springs are deflected and the lower tail of the springs will always be pressed against the
Pinch Roller Spacer (without a gap) as shown in Figure 3-19.
Y-ARM
MOUNTING SCREW
PINCH ROLLER
SPACER
PINCH ROLLER
ASSEMBLY
PINCH ROLLER ASSEMBLY
MUST TOUCH SPACER
IN THE AREA SHOWN
Figure 3-19. Correct Positioning of the Spring in the Pinch
Roller Support.
Maintenance 3-27
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- High-resolution printing up to 1200 x 1200 dpi
- Large print area of up to 60 inches wide
- Fast print speeds of up to 8 inches per second
- Built-in Ethernet and USB connectivity
- Easy-to-use control panel
Related manuals
Frequently Answers and Questions
What is the maximum resolution that the T-200 can print?
What is the largest print size that the T-200 can handle?
What is the fastest print speed that the T-200 can achieve?
Does the T-200 have built-in connectivity options?
How easy is it to use the T-200?
advertisement