advertisement
HOV Hi-PoE IPM
Aluminium housing with IPM technology for IP cameras
EN
English - Instructions manual
ENGLISH
Contents
1 About this manual
Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.
1.1 Typographical conventions
DANGER!
High level hazard.
Risk of electric shock. Disconnect the power supply before proceeding with any operation, unless indicated otherwise.
CAUTION!
Medium level hazard.
This operation is very important for the system to function properly. Please read the procedure described very carefully and carry it out as instructed.
INFO
Description of system specifications.
We recommend reading this part carefully in order to understand the subsequent stages.
2 Notes on copyright and information on trademarks
The quoted names of products or companies are trademarks or registered trademarks.
3 Safety rules
CAUTION! The device must be installed only and exclusively by qualified technical personnel.
• The manufacturer declines all responsibility for any damage caused by an improper use of the appliances mentioned in this manual.
Furthermore, the manufacturer reserves the right to modify its contents without any prior notice.
The documentation contained in this manual has been collected with great care. The manufacturer, however, cannot take any liability for its use. The same thing can be said for any person or company involved in the creation and production of this manual.
• Before starting any operation, make sure the power supply is disconnected.
• Do not use cables that seem worn or old.
• Never, under any circumstances, make any changes or connections that are not shown in this handbook. Improper use of the appliance can cause serious hazards, risking the safety of personnel and of the installation.
• Use only original spare parts. Non-original spare parts could cause fire, electrical discharge or other hazards.
• Before proceeding with installation, check the supplied material to make sure it corresponds to the order specification by examining the identification labels (4.2 Product markings, page 4).
• This device was designed to be permanently installed on a building or on a suitable structure.
The device must be installed permanently before any operation.
• When installing the device, comply with all the national standards.
MNVCHOVHPOE_1511_EN 3
4
• CAUTION! The electrical system to which the unit is connected must be equipped with a automatic bipolar circuit breaker. The circuit breaker for main supply voltage phase units must have a level of intervention of 20A max. The circuit breaker for low voltage units must have a level of intervention of 6A max. This circuit breaker must be of the
Listed type. The minimum distance between the contacts must be 3mm (0.1in). The circuit breaker must be provided with protection against the fault current towards the ground (differential) and the overcurrent (magnetothermal).
• Any device which could be installed inside the product must comply with the current safety standards.
• If the installation is NEMA TYPE 4X, the installer must replace the cable glands of the product with
NEMA TYPE 4X cable glands.
• Installation category (also called Overvoltage
Category) specifies the level of mains voltage surges that the equipment will be subjected to.
The category depends upon the location of the equipment, and on any external surge protection provided. Equipment in an industrial environment, directly connected to major feeders/short branch circuits, is subjected to Installation Category III. If this is the case, a reduction to Installation Category
II is required. This can be achieved by use of an insulating transformer with an earthed screen between primary and secondary, or by fitting listed Surge Protective Devices (SPDs) from live to neutral and from neutral to earth. Listed SPDs shall be designed for repeated limiting of transient voltage surges, suitable rated for operating voltage and designated as follows: Type 2 (Permanently connected SPDs intended for installation on the load side of the service equipment overcurrent device); Nominal Discharge Current (In) 20kA min.
For example: FERRAZ SHAWMUT, STT2240SPG-
CN, STT2BL240SPG-CN rated 120Vac/240Vac,
(In=20kA). Maximum distance between installation and reduction is 5m.
• Power supply to the product must be exclusively provided by the PoE cable (Power over Ethernet).
• For all connections, use cables that are able to withstand temperatures of at least 75°C (167°F).
• The product is designed to house only cameras that are properly certified (7W max).
• A disconnecting device, readily and easily accessible, must be incorporated in the electrical system of the building for rapid intervention.
• To connect the power supply line use the appropriate junction-box (UPTJBUL). For further information, refer to the product use and installation manual.
• Use Listed copper tube crimping lugs for the connection of the network conductors to the terminals. The copper tube crimping lugs must be suitable for the type of installation (from -20°C
(-4°F) a +80°C (+176°F) min., V-0). Copper tube crimping lugs examples: RP, BP o YP (Cembre).
4 Identification
4.1 Product description and type designation
The HOV Hi-PoE IPM housing exploits in an optimal way the POE and Hi-POE technology, using the power supplied by the Ethernet cable as the sole source of power for all the devices connected, thus ensuring the maximum efficiency and flexibility of the network system as well as user-friendly installation and low costs.
The innovative IPM (Intelligent Power Management) system enables extremely quick and easy installation with the use of a single Ethernet connecting cable.
The Hi-POE IPM system automatically detects all the options, like heating, fan and illuminator and then autonomously balances the power to ensure suitable distribution of the same to the connected devices. This guarantees the optimal operation of the
IP camera between -30°C (-22°F) and +60°C (140°F), with heat regulation and cold start (activation at low temperature).
The analog system, with previously installed camera housings, can be retrofitted on IPM system simply by changing the slide and the internal electronics.
This enables the digital conversion, speeding up the installation and thereby minimizing costs and environmental impact.
4.2 Product markings
See the label attached to the product.
MNVCHOVHPOE_1511_EN
5 Preparing the product for use
Any change that is not expressly approved by the manufacturer will invalidate the guarantee.
5.1 Unpacking and contents
5.1.1 Unpacking
When the product is delivered, make sure that the package is intact and that there are no signs that it has been dropped or scratched.
If there are obvious signs of damage, contact the supplier immediately.
Keep the packaging in case you need to send the product for repairs.
5.1.2 Contents
Check the contents to make sure they correspond with the list of materials as below:
• Housing
• RJ45 wiring
• Housing equipment:
• Allen wrench
• Spacers
• Cable glands gaskets
• Cable glands (x3)
• Bolts and screws
• Screws for camera
• Instructions manual
• Desiccant bag
5.2 Safely disposing of packaging material
The packaging material can all be recycled. The installer technician will be responsible for separating the material for disposal, and in any case for compliance with the legislation in force where the device is to be used.
When returning a faulty product we recommend using the original packaging for shipping.
5.3 Preparatory work before installation
5.3.1 Attaching the bracket
The product must be fastened with suitable equipment. The fastening means must guarantee the mechanical seal when a force equal to at least 4 times the weight of the device is applied.
MNVCHOVHPOE_1511_EN 5
6
6 Assembling and installing
The assembly and installation must be performed only by skilled personnel.
The product may be interfaced with devices not manufactured by VIDEOTEC. VIDEOTEC recommends a test prior to installation.
VIDEOTEC will not be liable for any installation costs or lost revenues in the event a compatibility problem will occur.
6.1 Installation
6.1.1 How to open the housing
Loosen the 2 screws on the side, turn the cover and the upper half of the body about the opening hinge axis.
At the end of istallation and cabling operations close the housing.
6.1.2 Removal of the slide
To remove the slide it is necessary to partially unscrew the fixing screws as shown in figure.
Move the slide, by sliding it until the holes coincide with the slide locking screws.
Fig. 1
6.1.3 Cable glands assembly
For the internal cable routing brackets it is necessary to use the sealing ring kit (OWBIP).
The reduced space does not allow the use of the supplied cable glands. The kit must be bought separately.
Inside the supply are 3 cable glands that must be installed at the bottom of the housing as shown in figure. The cable glands that are not used must be sealed with the cap to avoid water entering the housing.
Fig. 2
6.1.4 Installation of the GEKO IRH illuminator (optional)
Maximum power of the illuminator must not exceed 6W.
To install the illuminator it is necessary to use the illuminator bracket (OSUPPIR). The kit must be bought separately.
Use the cable glands or the smallest sealing ring to avoid water entering the housing.
For installation information on the illuminator on housing refer to the product's use and installation manual.
For further details on configuration and use refer to the relative chapter (6.1.8 Connection of the GEKO
IRH illuminator (optional), page 8).
MNVCHOVHPOE_1511_EN
6.1.5 Installation of the version with double filter for air renewal
During installation pay attention to the orientation of the air inlet filter fins.
6.1.6 Ethernet cable installation
Insert the Ethernet cable in the gasket and block it as shown in figure.
Fig. 3
Depending on the angle of inclination of the housing, the orientation of the filter fins must prevent water penetrating in case of rain:
To guarantee the weatherproof, install the housing on the support following the inclination limits as shown in the picture.
Fig. 5
Fit the gasket (01) to the cable gland M20 (02). Fasten the cable gland to the bottom of the housing (03) using the M20 nut (04).
Pay attention to the fixing. Tightening torque:
7Nm.
Pass the cable with connector RJ45 (05) through the
M20 cable gland (02). Tighten the cable gland plug
(06).
04
01
02
05
06
03
45°
0˚
Fig. 6
45°
Fig. 4 Maximum tilt of the transversal axis: 0°.
Maximum tilt of the longitudinal axis: ±45°.
MNVCHOVHPOE_1511_EN 7
Fig. 8
8
6.1.7 How to install the camera
The correct operation of the equipment, within the temperature range indicated, is guaranteed only if you use camera and lens with temperature limits equal to at least
-10°C and + 60°C.
It is possible to install only PoE type cameras.
Mount the camera using the supplied screws (01) and spacers (02).
Apply at least one spacer to guarantee electrical isolation between the slide and the camera.
Position the camera lens close to the glass to avoid visual interference or optical reflections.
Connect the camera to the J2 connector (PoE OUT) with the supplied cable (03).
03
02
6.1.8 Connection of the GEKO IRH illuminator (optional)
Connect the illuminator to the J6 terminal as described in the diagram below.
Fig. 9
CONNECTION OF THE GEKO IRH ILLUMINATOR
Illuminator Terminal J6
Brown (telemetry)
Blue (telemetry)
1
2
White (supply)
Black (supply)
3
4
Tab. 1
To adjust the lighting threshold of the illuminator refer to the product's use and installation manual.
01
1 2
3 4
Fig. 7
Refit the slide in its housing and fix the previously loosened screws.
MNVCHOVHPOE_1511_EN
6.1.9 PoE cable connection
Connect the PoE cable from the Power Injector to the
J1 connector.
6.1.11 Connection of the blower with double filter for air renewal (optional)
Connect the fan cable to the J4 connector.
Fig. 10
Before powering the device, you must set the maximum power consumption of the housing
operating on dip switch SW1 (7 Configuration, page
6.1.10 Connection of the de-icing heating of the glass (optional)
Connect the heating cable of the de-icing glass to the
J3 connector.
Fig. 12
7 Configuration
Before powering the device, you must set the maximum power consumption of the housing operating on dip switch SW1.
Fig. 11
MNVCHOVHPOE_1511_EN
Fig. 13
ABSORBED POWER CONFIGURATION
SW1 Maximum power
OFF
ON
PoE class 3 (13W max)
Hi-PoE class 4 (25W max)
Tab. 2
According to the absorbed power, the system can supply the options described in the table (Tab. 3, page 10).
9
HOV HI-POE IPM AVAILABLE MODELS AND FEATURES
Operating temperature
Injector Camera Demisting system
From -10°
(14°F) a +60°C
(140°F)
From -10°
(14°F) a +60°C
(140°F)
From -30°C
(-22°F ) a
+60°C (140°F)
PoE classe 3
(13W)
Hi-PoE class 4
(25W)
PoE classe 3
(13W)
Hi-PoE class 4
(25W)
Hi-PoE class 4
(25W)
Hi-PoE class 4
(25W)
Tab. 3
PoE max. class
2 (7W)
PoE max. class
3 (13W)
PoE max. class
2 (7W)
PoE max. class
3 (13W)
PoE max. class
3 (13W)
PoE max. class
3 (13W) p p p p p p
Illuminator
– p
– p
–
–
Heater
–
–
–
– p p
–
–
–
–
Anti-icing heated glass
–
Fan with double air filter
p p
–
– p
–
–
8 Switching on
The automatic pre-heating (De-Ice) process could be started whenever the device is switched on and the air temperature is below 0°C. This process is used to ensure that the device works properly even at low temperatures. The duration ranges between 60 and 120 minutes, depending on conditions.
During the lighting phase the device reads the status of the dip switch and automatically detects all the connected options for the correct energy management of the housing.
The LEDs shown in the figure allow to check the product's operating status.
Fig. 14
Refer to the table to identify the operating status.
10 MNVCHOVHPOE_1511_EN
OPERATING STATUS
LED LED Status Apparatus Status
LD1 (Power supply)
LD2 (Camera)
LD3 (Demisting)
LD4 (Heater)
LD5 (Illuminator)
LD6
(Delayed activation)
Off
On
The device is not powered
The device is correctly powered
Off
On
1 flashing
The camera is not connected or
Cold Start is active
The camera is correctly powered
The camera has a low identification resistance
2 flashings The camera has a high identification resistance
5 flashings The camera has an excessive energy consumption
9 flashings The camera requires more energy than the available
Off Demisting was not correctly detected
1 flashing
On
Standard demisting is inactive
2 flashings The anti-ice system (optional) is inactive
Demisting, or anti-ice system, is in function
Off
1 flashing
On
Off
1 flashing
Heating is not available or power available is not sufficient
Heating is inactive
Heating is active
The illuminator (optional) is not detected or the available power is not sufficient
The illuminator is correctly powered (illuminator activation is controlled by its photocell)
Off
1 flashing
On
Heating is not available
The pre-heating procedure is inactive
The pre-heating procedure is underway
Tab. 4
9 Maintaining and cleaning
9.1 Maintaining
9.1.1 Kit for upgrading of the systems
The kit cannot be installed in the housing versions equipped with wiper.
Remove the slide (01), the electronic board (02) and the heating (03).
02
01
03
Fig. 15
For kit installation information refer to chapter 6
Assembling and installing, page 6.
9.2 Cleaning
9.2.1 Window and plastic cover cleaning
Avoid ethyl alcohol, solvents, hydrogenated hydrocarbide, strong acid and alkali. Such products may irreparably damage the surface.
We recommend using a soft cloth with neutral soaps diluted with water or specific products to clean the glasses lenses.
MNVCHOVHPOE_1511_EN 11
10 Disposal of waste materials
This symbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area of the world.
Your product is designed and manufactured with high quality materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.
Please dispose of this equipment at your local
Community waste collection or Recycling centre.
In the European Union there are separate collection systems for used electrical and electronic products.
11 Technical data
11.1 General
Constructed from aluminium
Sunshield in ABS
Epoxypolyester powder painting, RAL9002 colour
Stainless steel external screws
11.2 Mechanical
Cable glands: 1xM12, 1xM16, 1xM20
Glass window (WxH): 118x75mm (4.6x2.7in)
Internal usable area (WxHxL): 100x70x250mm
(3.9x2.7x9.8in)
Unit weight: 3.1kg (6.6lb)
11.3 Electrical
Power absorbed in input: PoE class 3 (13W) or Hi-PoE class 4 (25W) selectable from dip switch
Available power for camera (PoE IN class 3): PoE Class
2 (7W)
Available power for camera (Hi-PoE IN class 4): PoE class 3 (13W) with Ton -10°C ±2°C “cold start” function
Data line: 10/100Base-T
Illuminator GEKO IRH, low power: 6W
Heater: 8W, electronically controlled, Ton 20°C±2°C
(68°F±4°F), Toff 23°C±2°C (73.4°F±4°F)
Fan with thermostat for camera cooling for versions with double air filter: Ton 35°C±2°C (95°F±4°F), Toff
32°C±2°C (89.6°F±4°F)
Demisting with forced hot air: 5W
Anti-icing heated glass: 5W, Ton 30°C±2°C (86°F±4°F),
Toff 33°C±2°C (91.4°F±4°F)
Compatible with IEEE 802.3af, IEEE 802.3at/PoE Plus
Compatible with the Power Injector (OHEPOWINJ:
VIDEOTEC optional accessory)
11.4 Environment
Indoor/Outdoor
Operating temperature: From -10° (14°F) a +60°C
(140°F)
Operating temperature (with heater): From -30°C
(-22°F ) a +60°C (140°F)
11.5 Certifications
Electrical safety (CE): EN60950-1
Electromagnetic compatibility (CE): EN50130-4,
EN61000-6-4
IP protection degree: EN60529
• IP66/IP67 (with cable glands)
• IP66/IP67 (with special gaskets and bracket with internal cable channel)
• IP55 (with bracket with internal cable channel)
• IP44 (for models with double filter for ventilation)
Salty fog resistance: ISO9227, to 1000 hours
UL certification: cULus Listed,TYPE 4X (except for version with double filter for the air exchange,
HOV32K2A716)
EAC certification
12 MNVCHOVHPOE_1511_EN
12 Technical drawings
The dimensions of the drawings are in millimetres.
250 100
USABLE
AREA
B
USABLE AREA
A - A
514
B - B
176
A
B
A
70 189
40 114
413
Fig. 16 HOV HiPoE IPM.
401
165
MNVCHOVHPOE_1511_EN 13
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. +39 0445 697411 - Fax +39 0445 697414
Email: [email protected]
Asia Pacific Videotec (HK) Ltd
Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street
Kwai Chung, New Territories - Hong Kong
Tel. +852 2333 0601 - Fax +852 2311 0026
Email: [email protected]
France Videotec France SARL
Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf
91140 Villebon sur Yvette - France
Tel. +33 1 60491816 - Fax +33 1 69284736
Email: [email protected]
Americas Videotec Security, Inc.
Gateway Industrial Park, 35 Gateway Drive, Suite 100
Plattsburgh, NY 12901 - U.S.A.
Tel. +1 518 825 0020 - Fax +1 518 825 0022
Email: [email protected] - www.videotec.us
www.videotec.com
MNVCHOVHPOE_1511_EN
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement