advertisement
5.4.1 Hydraulic pressure loss of the heat pump circuit
REPAIR WORK
6.2 Draining the heat pump circuit
B
A
A
B
A Glycol water circuit fl ow to heat pump
A
B Glycol water circuit return from heat pump
300
250
200
150
100
50
0
1
2
500 1000 1500 2000 2500 3000
B Flow rate (l/hour)
1 50% glycol circuit fl ow rate
B
C
► Connect the drain pipe to tap (C).
► Insert the other end of the pipe into a suitable container to collect the glycol.
► Open the tap (B).
► Open the heat pump circuit air bleed valve.
► Check the water-tightness of the system.
5.5 Handing over the product to the user
After completing the installation:
► Answer any questions the user may have.
► Draw special attention to the safety instructions which the user must follow.
6.4 Checking the electrical installation
► Check the electrical installation observing all relevant regulations.
6.4.1 Checking the cables
► If the power cable of this product is damaged, then to prevent danger, only the manufacturer, the after-sales service or similarly qualifi ed persons shall replace the power cable.
► In case you need spare parts during maintenance or repair, exclusively use genuine spare parts.
The genuine component parts of the product have been certifi ed together with the product in the course of the CE conformity check. If you do NOT use certifi ed genuine spare parts during maintenance or repair, the CE conformity of the product will expire. That is why we imperatively recommend to install genuine spare parts.
7 Decommissioning
► Isolate the product from the power mains.
► Drain the appliance (see chapter 6.2).
► De-install the product.
► Recycle or dispose the product and its components (see chapter 8).
0020166669_04 - 03/15 - Vaillant
23
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Normen)
- 7 Hinweise zur Dokumentation
- 7 Mitgeltende Unterlagen beachten
- 7 Aufbau des Produktes
- 7 Typenbezeichnung und Serialnummer
- 8 Montage und Installation
- 8 Vorbereitung der Montage und Installation
- 11 Durchführung und Verlegung der Kabel
- 11 Auffüllen des Wärmepumpenkreislaufs
- 11 Entlüften des Gerätes
- 12 Verfügbare Förderhöhe des Heizkreises
- 12 Gerät an den Betreiber übergeben
- 13 Entleeren des Wasserpumpenkreislaufs
- 13 Überprüfung der Dichtigkeit
- 13 Überprüfung der Elektroinstallation
- 13 Recycling und Entsorgung
- 17 Required personnel qualifi cations
- 17 General safety advices
- 18 Regulations (directives, laws, standards)
- 19 Notes on the documentation
- 19 Observe other applicable documents
- 19 Validity of the instructions
- 19 Description of the product
- 19 Type designation and serial number
- 20 Data plate description
- 20 Mounting and installation
- 20 Preparing the mounting and installation
- 21 Mounting the product
- 23 Cableway and passage
- 23 Filling the heat pump circuit
- 24 Draining the product
- 24 Installing the casing
- 24 circuit
- 25 Handing over the product to the user
- 25 Draining the heat pump circuit
- 25 Checking the electrical installation
- 26 Recycling and disposal
- 31 1.1 Qualifi ca dell’utente
- 31 Necessaria abilitazione del personale
- 31 Norme generali di sicurezza
- 32 Prescrizioni (direttive, leggi, norme)
- 33 Note relative alla documentazione
- 33 Rispetto dei documenti
- 33 Conservazione della documentazione
- 33 Validità del manuale
- 33 Modello e numero di serie
- 34 Descrizione della targhetta identifi cativa
- 34 Montaggio e installazione
- 34 e dell'installazione
- 37 Passaggio dei cavi
- 37 Messa in servizio
- 37 Riempimento del circuito pompa di calore
- 38 Installazione della parte frontale
- 38 riscaldamento
- 39 Pezzi di ricambio
- 39 Scarico del circuito pompa di calore
- 39 6.3 Verifi ca della tenuta stagna
- 39 6.4 Verifi ca dell’impianto elettrico
- 39 Messa fuori servizio defi nitiva
- 40 Riciclaggio e smaltimento
- 45 1.1 Cualifi cación del usuario
- 45 1.3 Cualifi cación requerida para el personal
- 45 Consignas generales de seguridad
- 46 1.7 Identifi cación CE
- 47 Observaciones relativas a la documentación
- 47 Respeto de los documentos aplicables
- 47 Conservación de los documentos
- 47 Validez del manual
- 47 Descripción del aparato
- 47 Estructura del aparato
- 47 Modelo y número de serie
- 48 Descripción de la placa de características
- 48 Montaje e instalación
- 48 Preparación del montaje y de la instalación
- 49 Montaje del aparato
- 51 Paso y direccionamiento de los cables
- 51 Puesta en servicio
- 51 Llenado del circuito de la bomba de calor
- 52 Purga del aparato
- 52 Instalación de la carcasa
- 53 Información al usuario
- 53 Piezas de recambio
- 53 Vaciado del circuito de la bomba de calor
- 53 Comprobación de la estanqueidad
- 53 Comprobación de la instalación eléctrica
- 53 Puesta fuera de servicio defi nitiva
- 54 Reciclaje y eliminación
- 54 Servicio de atención al cliente