MOUNTING OF HANDLE. Makita BCM2310CA, BCM2310, BCM3310CA, BCM3310, BCM2610, BCM3300, BCM2600, BCM2610CA
Add to My manuals
44 Pages
advertisement
MOUNTING OF HANDLE
CAUTION:
Before doing any work on the Brush Cutter/String Trimmer, always stop the engine and pull the spark plug connector off the spark plug.
Always wear protective gloves.
CAUTION:
Start the engine of Brush Cutter/String Trimmer after making sure that it is assembled completely.
For machines with U Handle models
- Place the handle-fixing metal so that the handle with the control lever will be positioned on the right (the right-hand grip side) as viewed from the engine side, and the other handle on the left side.
- Fit the groove of the handle-fixing material to the handle end. Fix the attached metal by hexagon socket bolts supplied.
- Adjust the position of handle for easy and comfortable operation, and then tighten securely the four (4) hexagon socket bolts uniformly on the right and left with the wrench provided.
- Wrap the waist pad around the shaft so that the hanger (1) will come out through the slit in the waist pad and control cable (3) will also wrapped under the waist pad (2).
STOP
BCM2600
BCM3300
(1)
(2)
(3)
BCM2600,
BCM3300
For machines with Loop Handle
- Fix a barrier to the left side of the machine together with the handle of operator’s protection.
- Do not adjust position of the loop handle too close to the control grip.
- The handle must be kept in position more than 250 mm from the hanger.
MOUNTING OF PROTECTOR
To meet the applicable safety provisions, only the tool/protector combinations as described in the table must be used.
Use genuine MAKITA cutter blades or nylon cutting head.
The cutter blade must be well sharpened, free of cracks or breakage. If the cutter blade hits against a stone during operation, stop the engine and check the blade immediately.
Star Blade
Eddy Blade Protector for metal blades
Nylon cutting head to Engine
BCM2310
BCM2610
BCM3310
Protector for cord cutter
20
Sharpen or replace the cutter blade every three (3) hours of operation.
If the nylon cutting head hits against a stone during operation, stop the engine and check the nylon cutting head immediately.
CAUTION:
The appropriate blade guard must always be installed for your own safety and complying with accident-prevention regulations.
Operation without the safety guard is not permitted.
8
advertisement
Related manuals
advertisement
Table of contents
- 4 SYMBOLS
- 5 SAFETY INSTRUCTIONS
- 7 TECHNICAL DATA
- 8 MOUNTING OF HANDLE
- 8 MOUNTING OF PROTECTOR
- 9 MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD
- 10 FUELS/REFUELING
- 10 CORRECT HANDLING OF MACHINE
- 11 POINTS IN OPERATION AND HOW TO STOP
- 11 RE-SHARPENING THE CUTTING TOOL
- 12 SERVICING INSTRUCTIONS
- 13 STORAGE
- 17 SYMBOLES
- 18 CONSIGNES DE SÉCURITÉ
- 20 DONNÉES TECHNIQUES
- 22 ASSEMBLAGE DE LA POIGNÉE
- 22 ASSEMBLAGE DU PROTECTEUR
- 23 OU DE LA TÊTE DE COUPE EN NYLON
- 24 CARBURANTS/REMPLISSAGE
- 24 COMMENT TENIR L'OUTIL
- 25 ET FAÇON D'ARRÊTER L'OUTIL
- 26 INSTRUCTIONS POUR LA RÉPARATION
- 27 RANGEMENT
- 31 SÍMBOLOS
- 32 INSTRUCCIONES DE SEGURIDAD
- 34 DATOS TÉCNICOS
- 36 MONTAJE DEL ASIDERO
- 36 MONTAJE DEL PROTECTOR
- 37 MONTAJE DEL DISCO O EL CABEZAL DEL CORDÓN DE NYLON
- 38 COMBUSTIBLE/REPOSTAJE
- 38 MANEJO CORRECTO DE LA MÁQUINA
- 39 EN LA OPERACIÓN Y CÓMO PARAR
- 39 AFILADO DEL IMPLEMENTO DE CORTE
- 40 INSTRUCCIONES DE MANTENIMIENTO
- 41 ALMACENAMIENTO