advertisement
Declaration of incorporation for partially completed machinery
Operation and maintenance manual
Appendix 1. Declaration of incorporation for partially completed machinery
(Machinery Directive 2006/42/EC, Annex II, 1.B.)
Manufacturer: Alamarin-Jet Oy
Tuomisentie 16
FI-62300 Härmä, Finland
Compiler of the technical file:
Description of the partially completed machinery:
Water jet propulsion device
Operation of the partially completed machinery:
Hannu Rantala, Technical Manager
Alamarin-Jet Oy
Tuomisentie 16
FI-62300 Härmä, Finland
Model and type of the partially completed machinery:
The device is intended to be used as the propulsion device of a motor boat.
A propulsion device transforms the torque of the motor into propulsive force.
Jet-288
Serial number of the partially completed machinery:
_____________________________________
Alamarin-Jet Oy guarantees that the abovementioned partially completed machinery meets the requirements of the Machinery Directive (2006/42/EC) and the validating national regulations.
In addition, the company guarantees that
• the specific technical documents related to the partially completed machinery have been created according to section B of Annex VII in the
Machinery Directive (2006/42/EC), and
• the following harmonised standards are applied: SFS-EN-ISO 12100-1 and
SFS-EN-ISO 14121-1.
Alamarin-Jet Oy also undertakes to deliver the documents related to the partially completed machinery to the relevant national authority in electronic format if so requested.
The partially completed machinery must not be introduced to use before the final equipment to which it is intended to be attached has been declared to conform to the requirements of this Directive.
Place: Kauhava, Finland
_________________________________
Date and Signature
KHO/288/EN/1.3.0.
37
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Operation and maintenance manual
- 3 Table of contents
- 5 1. Introduction
- 5 1.1. Safety precautions
- 5 1.2. Symbols
- 7 2. The jet propulsion unit
- 7 2.1. Structure
- 8 2.2. Serial number
- 9 3. Operation
- 9 3.1. Starting
- 10 3.2. Steering
- 11 3.3. Controlling
- 11 3.3.1. The positions of the reversing deflector control lever
- 12 3.3.2. Using the reversing deflector
- 13 3.4. Driving under difficult conditions
- 13 3.5. Dry running
- 15 4. Maintenance
- 15 4.1. Washing
- 15 4.2. Corrosion protection
- 15 4.2.1. Changing the anodes
- 17 4.2.2. Touch-up painting and antifouling
- 19 4.3. Bearing
- 19 4.3.1. Lubricating the front bearing
- 20 4.3.2. Lubrication of the rear end bearing
- 22 4.4. Control system
- 23 4.5. Seals
- 23 4.6. Hydraulic reversing deflector control system
- 26 4.7. Raw water cooling
- 27 4.8. Impeller
- 28 4.8.1. Checking the impeller
- 28 4.8.2. Removing the impeller
- 30 4.8.3. Installing the impeller
- 32 4.9. Intermediate shaft
- 35 5. Problem situations
- 35 5.1. Cavitation
- 37 5.2. Ventilation
- 37 5.3. Clogged jet
- 41 Appendix 1. Declaration of incorporation for partially completed machinery
- 42 Appendix 2. After sales questionnaire
- 45 Appendix 3. Grease recommendations
- 46 Appendix 4. Oil recommendations
- 47 Appendix 5. Tightening torques