advertisement
OTHER SETTINGS
Browse Dest.
– If the Destination drive is formatted with a FAT32 partition, Browse
Destination will allow the user to navigate directories on the drive. It will also show the size of files on the drive. Use the Arrow and
Select icon to navigate the directories.
Print Options
This mode is used to print reports directly from the Dossier through the serial port. This menu is used to prep the Destination drive(s) prior to running a DD Image capture. The settings available are:
Eject Page
This function sends a form feed signal to the printer. This function may be required to load paper in some printers.
Print Report
This function is used to manually print a report after a capture session. It also prints different reports associated with Keyword
Search.
Print Last Session
– This function prints the report from the last performed session
(drive capture, defect scan, wipe, etc.). It is not able to print reports prior to the last session.
Print Search Detail
– This function prints all of the found keywords from the last keyword search as well as their absolute locations on the Source drive.
NOTE: For more information, please refer to Chapter 7: Keyword Searching.
Print Search Text
– This function prints a fragment of text before and after each found keyword. This allows each keyword to be viewed in context.
NOTE: For more information, please refer to Chapter 7: Keyword Searching.
Auto Print (After Capture)
This function tells the Dossier to print a report after the next capture session. It can be set to YES or NO (default).
Forensic Dossier
User’s Manual
52
OTHER SETTINGS
Debug
Use this setting to turn the Debug reporting tool on and off. This setting is used in conjunction with Serial Port 2 and a terminal link program. The default setting is OFF. Debug should only be turned on when the user is directed to do so by Logicube Technical Support.
Beeper
Use this setting to turn the beeper on and off. This setting is useful when in
“stealth” mode or in an environment that requires no noise. The default setting is
OFF. Any change to the setting is preserved after power off.
Audio Notice for Error
Use this setting to provide an audible beep if the data capture has been completed successfully. A different audible beep will occur to alert the user that the capture has encountered an error. This beep will sound with a 50% duty cycle for approximately 2 minutes or until the user acknowledges the error via the user interface. The default setting for Audio Notice is OFF. Once enabled the Dossier will retain the setting last used prior to power recycle.
Security
This feature provides the user with a password-based security system (based on the ATA security specification T13) to protect their data from unauthorized access.
This feature has two security levels; High or
Maximum and the ability to set a Master along with a User password. The Master password is typically used by an administrator
– this password is kept secret from the user and may be used to unlock the device if the User password is lost. If High security is selected the drive can be
Forensic Dossier User’s Manual
53
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 9 1. INTRODUCTION TO THE FORENSIC DOSSIER
- 16 2. GETTING STARTED
- 17 Opening the Logicube Dossier
- 18 Connecting a PATA Drive
- 20 Connecting a Serial ATA (SATA) Drive
- 21 Connecting other types of drives
- 22 Calibrating the Touch Screen
- 26 3. DRIVE CAPTURE MODES AND SETTINGS
- 26 Drives
- 27 Settings
- 27 About
- 33 Verify Disk or File
- 33 File Size
- 45 4. OTHER MODES
- 45 Procedure
- 50 Contrast
- 50 Save Settings
- 50 Factory Settings
- 52 Eject Page
- 52 Print Report
- 52 Auto Print (After Capture)
- 54 High Security
- 54 Maximum Security
- 56 Disabled
- 57 Performing SAS and SCSI Adapter Updates
- 63 5. CAPTURING RAID CONFIGURATIONS
- 64 Drive Capture and DD Capture
- 64 Verify
- 64 Calculate HASH and Keyword Search
- 65 6. USB AND FIREWIRE PORTS
- 69 How to set up and use the USB/FireWire cloning software
- 70 Selectable Capture Modes & Options
- 73 Cloning a Mac using FireWire and the Cloning Software
- 73 Additional Notes
- 75 7. KEYWORD SEARCHING
- 76 Procedure
- 82 8. OPTIONAL PERIPHERALS
- 82 (MPFS™)
- 101 9. INTERNAL FLASH MEMORY
- 104 10. SOFTWARE AND FIRMWARE LOADING INSTRUCTIONS
- 107 11. REFERENCE
- 107 Options
- 108 Erase process with Security Erase
- 108 Erase process using non Security Erase drives
- 108 HASH + V
- 113 Erase Process
- 113 Write a unique signature to the destination drive
- 114 Information Format
- 119 12. FREQUENTLY ASKED DOSSIER QUESTIONS AND ANSWERS
- 121 13. INDEX