- No category
advertisement
▼
Scroll to page 2
of
107
58
8.5 Setting up tank gear alarms
8.5. Setting up tank gear alarms
Gear alarms will trigger if the gear ratio value entered in the drive setup menu is different to the value calculated based on the shaft sensor and motor encoder.
1. Select Settings Menu / Alarm Settings Menu / Tank
Gear Alarms
.
2. Select Tank Gear # to enable the alarm. # denotes the tank number.
advertisement
Related manuals
advertisement
Table of contents
- 17 Introduction
- 19 Seeder Settings
- 19 2.1. Setting up the seeder
- 23 2.2. Setting up tanks
- 23 2.2.1. Granular tank settings
- 27 2.2.2. Liquid/NH3 tank settings
- 32 2.3. Setting up external options
- 34 2.4. Setting up tank preload time
- 35 2.5. Setting up wheel factor
- 35 2.5.1. Manual entry of wheel factor
- 35 2.5.2. Automatic calibration of wheel factor
- 38 2.6. Setting up fans
- 39 2.7. Setting up width and speed
- 41 2.8. Settings for blocked heads
- 42 2.9. Viewing operating history
- 43 2.10. Selecting seeder brand
- 45 ECU Setup
- 47 Product Settings
- 47 4.1. Setting up products
- 49 Calibrating the Tanks
- 50 5.1. Manual entry of calibration factor
- 51 5.2. Automatic calculation of calibration factor
- 51 5.2.1. Calibrating a single granular tank
- 55 5.2.2. Calibrating multiple granular tanks
- 58 5.2.3. Calibrating a liquid tank
- 61 Area Test
- 61 6.1. Performing the area test
- 63 External Keypad
- 63 7.1. Keypad setup
- 66 7.2. LED behavior
- 69 Alarm Settings
- 69 8.1. Managing seeder alarms
- 71 8.2. Setting up fan alarms
- 72 8.3. Setting up tank motor alarms
- 73 8.4. Setting up shaft alarms
- 74 8.5. Setting up tank gear alarms
- 75 8.6. Setting up tank alarms
- 76 8.7. Setting up tank pressure alarms
- 77 8.8. Setting up other alarms
- 78 8.9. Setting up no flow alarms
- 79 Advanced Settings
- 79 9.1. Configuring advanced settings
- 81 9.2. Upgrading ECU firmware
- 81 9.2.1. CM-40 Main ECU
- 82 9.2.2. CM-40 Aux ECU / EM-24 ECU
- 83 9.2.3. Verifying upgrade
- 85 Seeder Operation
- 85 10.1. Selecting the seeder operation screen
- 89 10.2. Selecting and filling tanks
- 90 10.3. Selecting and resetting area counters
- 91 10.4. Viewing diagnostics
- 93 Record User Data
- 93 11.1. Recording user data
- 95 Apollo ECU Information
- 95 12.1. Interpreting Apollo ECU LEDs
- 95 12.1.1. Power LEDs
- 97 12.1.2. Transmit LED
- 97 12.1.3. Receive LED
- 98 12.1.4. ECU Status LED
- 99 12.2. Apollo ECU error codes
- 99 12.2.1. Error levels
- 99 12.2.2. Error code signature
- 99 12.2.3. CM-40 ECU error codes
- 102 12.2.4. EM-24 ECU error codes
- 103 12.2.5. Decoding error codes