- No category
advertisement
Seeder Operation
This chapter describes how to operate the Apollo ISOBUS UT seeder.
10.1. Selecting the seeder operation screen
1. Select from the main Universal Terminal screen to open the Seeder screen.
Operation screen 1
69
70
10.1 Selecting the seeder operation screen
Icon Description
Used to select the required tank/s (the Select button in each tank may also be used). All tanks may be selected simultaneously.
Tanks that do not have a product assigned may be selected using this method.
The current speed of the vehicle/implement as calculated from the configured speed source.
The instantaneous coverage rate. Calculated by speed and width with at least one tank turned on. For example: an implement of 10 m width, moving at 10 km/hr gives a coverage rate of 10 hectares/hr.
Fan 1 and/or 2 RPM (if enabled in Fan Settings screen)
Fan 1 and/or 2 Pressure (if enabled in Fan Settings screen)
Toggles between operation screen 1 and 2.
Enable/disable the selected tank.
Activate preset application rates. See Setting up products, page 31.
Increase/decrease product in tank by set amount. See
The master switch may be controlled via the operation
screen if set to Virtual or Keypad/Virtual. See Setting up external options, page 16.
Operation screen 2
Chapter 10 – Seeder Operation
Icon Description
Currently selected Area number for accumulating data.
Total (cumulative) area covered. At least one tank must be turned on.
Cumulative area covered for the selected tank (see
TankNum below) and area (see AreaNum above).
Currently selected tank for displaying SubArea and
Weight totals.
Total product output for the selected tank (TankNum) and area (AreaNum).
Select the settings menu. See Settings menu, page 4.
Reset the sub area counter. See Selecting and resetting area counters, page 74.
Resets the total area. See Selecting and resetting area counters, page 74.
Display the diagnostics screen. See Viewing diagnostics, page 75.
71
72
10.1 Selecting the seeder operation screen
Icon Description
Temporary manual speed. Used to perform tank calibration or to calculate application rates.
Displays if the vehicle is stationary and a setting other than
Manual is selected as the speed source. See Setting up width and speed, page 23.
Selecting the icon toggles temporary manual speed .
Temporary manual speed is automatically cancelled when the vehicle starts moving.
advertisement
Related manuals
advertisement
Table of contents
- 17 Introduction
- 19 Seeder Settings
- 19 2.1. Setting up the seeder
- 23 2.2. Setting up tanks
- 23 2.2.1. Granular tank settings
- 27 2.2.2. Liquid/NH3 tank settings
- 32 2.3. Setting up external options
- 34 2.4. Setting up tank preload time
- 35 2.5. Setting up wheel factor
- 35 2.5.1. Manual entry of wheel factor
- 35 2.5.2. Automatic calibration of wheel factor
- 38 2.6. Setting up fans
- 39 2.7. Setting up width and speed
- 41 2.8. Settings for blocked heads
- 42 2.9. Viewing operating history
- 43 2.10. Selecting seeder brand
- 45 ECU Setup
- 47 Product Settings
- 47 4.1. Setting up products
- 49 Calibrating the Tanks
- 50 5.1. Manual entry of calibration factor
- 51 5.2. Automatic calculation of calibration factor
- 51 5.2.1. Calibrating a single granular tank
- 55 5.2.2. Calibrating multiple granular tanks
- 58 5.2.3. Calibrating a liquid tank
- 61 Area Test
- 61 6.1. Performing the area test
- 63 External Keypad
- 63 7.1. Keypad setup
- 66 7.2. LED behavior
- 69 Alarm Settings
- 69 8.1. Managing seeder alarms
- 71 8.2. Setting up fan alarms
- 72 8.3. Setting up tank motor alarms
- 73 8.4. Setting up shaft alarms
- 74 8.5. Setting up tank gear alarms
- 75 8.6. Setting up tank alarms
- 76 8.7. Setting up tank pressure alarms
- 77 8.8. Setting up other alarms
- 78 8.9. Setting up no flow alarms
- 79 Advanced Settings
- 79 9.1. Configuring advanced settings
- 81 9.2. Upgrading ECU firmware
- 81 9.2.1. CM-40 Main ECU
- 82 9.2.2. CM-40 Aux ECU / EM-24 ECU
- 83 9.2.3. Verifying upgrade
- 85 Seeder Operation
- 85 10.1. Selecting the seeder operation screen
- 89 10.2. Selecting and filling tanks
- 90 10.3. Selecting and resetting area counters
- 91 10.4. Viewing diagnostics
- 93 Record User Data
- 93 11.1. Recording user data
- 95 Apollo ECU Information
- 95 12.1. Interpreting Apollo ECU LEDs
- 95 12.1.1. Power LEDs
- 97 12.1.2. Transmit LED
- 97 12.1.3. Receive LED
- 98 12.1.4. ECU Status LED
- 99 12.2. Apollo ECU error codes
- 99 12.2.1. Error levels
- 99 12.2.2. Error code signature
- 99 12.2.3. CM-40 ECU error codes
- 102 12.2.4. EM-24 ECU error codes
- 103 12.2.5. Decoding error codes