advertisement
1.
1.1
1.2
Introduction
Features
● Atmel ATSAM4E16E microcontroller
● Embedded debugger (EDBG)
● USB interface
● Programming and debugging (target) through Serial Wire Debug (SWD)
● Virtual COM-port interface to target via UART
● Atmel Data Gateway Interface (DGI) to target via USART or TWI
● Four GPIOs connected to target for code instrumentation
● Digital I/O
● Two mechanical buttons (user, reset and force wakeup button)
● One user LED
● Three extension headers
● Xplained Pro LCD extension connector
● One CAN-bus
● 10/100-T Ethernet
● 2Gb 8-bit NAND Flash
● Dual 512K 8-bit SRAM
● Target USB, device mode
● Three possible power sources
● External power
● Embedded debugger USB
● Target USB
● 12MHz crystal
● 32kHz crystal
Kit Overview
The Atmel SAM4E Xplained Pro evaluation kit is a hardware platform to evaluate the Atmel ATSAM4E16E.
The kit offers a set of features that enables the ATSAM4E16E user to get started using the ATSAM4E16E peripherals right away and to get an understanding of how to integrate the device in their own design.
Atmel SAM4E Xplained Pro [USER GUIDE]
42216A-MCU-01/2014
3
Figure 1-1. SAM4E Xplained Pro Evaluation Kit Overview
Atmel SAM4E Xplained Pro [USER GUIDE]
42216A-MCU-01/2014
4
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Preface
- 2 Table of Contents
- 3 1. Introduction
- 3 1.1. Features
- 3 1.2. Kit Overview
- 5 2. Getting Started
- 5 2.1. Quick-start
- 5 2.2. Connecting the Kit
- 5 2.3. Design Documentation and Related Links
- 6 3. Xplained Pro
- 6 3.1. Embedded Debugger
- 6 3.2. Hardware Identification System
- 7 3.3. Power Supply
- 7 3.3.1. Measuring SAM4E Power Consumption
- 7 3.4. Standard Headers and Connectors
- 7 3.4.1. Xplained Pro Standard Extension Header
- 8 3.4.2. Xplained Pro LCD Connector
- 10 3.4.3. Xplained Pro Power Header
- 11 4. Hardware User Guide
- 11 4.1. Connectors
- 11 4.1.1. I/O Extension Headers
- 12 4.1.2. LCD Extension Connector
- 14 4.1.3. Chip Erase Header
- 14 4.1.4. Other Headers
- 14 4.2. Peripherals
- 14 4.2.1. SRAM
- 15 4.2.2. NAND Flash
- 16 4.2.3. Ethernet
- 17 4.2.4. SD Card Connector
- 17 4.2.5. CAN
- 17 4.2.6. USB
- 17 4.2.7. Crystals
- 18 4.2.8. Mechanical Buttons
- 18 4.2.9. LED
- 18 4.3. Embedded Debugger Implementation
- 18 4.3.1. Serial Wire Debug
- 18 4.3.2. Virtual COM Port
- 19 4.3.3. Atmel Data Gateway Interface
- 20 5. Kit Specific Data
- 21 6. Hardware Revision History and Known Issues
- 21 6.1. Identifying Product ID and Revision
- 21 6.2. Revision 3
- 22 7. Document Revision History
- 23 8. Evaluation Board/Kit Important Notice