- No category
advertisement
5 Controls
‹ Menu explanations
The fi rst message of the start-up sequence after the unit is turned on.
Degudent KBO
V1.00 ...booting...
Here you can load programs from internal memory or from a USB memory stick.
Load Þ xed programs
After turning on, the unit performs a self-test to check all systems and input/output connectors.
Selftest
Here you can start a software update, provided a USB memory stick with the new software version has been inserted.
Update
The values discussed in “Firing parameters” are shown in the main menu, which is always displayed when the unit is operating.
Main menu
(last program)
Here you can start a data backup.
Data backup
Here you can invoke additional submenus for system confi guration (see “Moving through the menus/Menu overview”)
ConÞ guration
Here you can change the language in which the menus are displayed.
Language
[German, English]
Here you can enter a calibration offset determined by a calibration using a silver wire test (see “Calibration”).
Calibration
Here you can pre-set the base temperature (default:
400 °C); see the diagram in “Firing parameters”.
Basic temperature
[°C/°F]
Here you can delete programs you have saved.
Delete program
Here you can determine whether the muffl e will heat in standby mode (see “Entering standby mode”).
Standby temperature
[°C/°F]
18
MultimatEasy
Controls 5
Here you can determine whether the vacuum pump will run in standby mode (see “Entering standby mode”).
Standby Vacuum
[on/off]
Here you can switch between °C and °F as a temperature unit.
°C / °Fahrenheit
[°C/°F]
Here you can turn the beep signals on or off. If the beep signal is turned on, you get:
A short tone each time a key is pressed; a long tone for each invalid entry; three tones at the end of a program.
Acoustic signal
[on/off]
Indicates the operating hours for the muffl e.
Hours mufß e:XX:YY
Indicates the operating hours for the vacuum pump.
Hours pump:XX:YY
Indicates the total operating hours for the
Multimat ® Easy.
Hours furnace:XX:YY
MultimatEasy
19
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 ‹ Content
- 5 1 General
- 5 ‹ On these Instructions for Use
- 5 ‹ Layout elements used in these Instructions for Use
- 6 ‹ Unit types and year of manufacture
- 6 ‹ Manufacturer and service addresses
- 6 ‹ Intellectual property rights
- 6 ‹ Proper use
- 7 2 Safety notes
- 7 ‹ Safe transport
- 7 ‹ Safe operation
- 8 ‹ Safe maintenance and troubleshooting
- 8 ‹ Safe handling of ceramic fi bres
- 8 ‹ Warning decals on the unit
- 9 3 Technical description
- 9 ‹ Base unit
- 10 ‹ Connectors
- 10 ‹ Scope of delivery
- 11 ‹ Optional accessories
- 11 ‹ Technical specifi cations and operating environment
- 12 ‹ Features
- 13 Setup
- 13 ‹ Unpacking and checking accessories
- 13 ‹ Setting up and connecting
- 13 ‹ Pre-heating
- 14 5 Controls
- 14 ‹ Control panel
- 15 ‹ Display
- 15 ‹ Firing parameters
- 17 ‹ Moving through the menus/Menu overview
- 18 ‹ Menu explanations
- 20 6 Operation
- 20 ‹ Turning on the unit/Starting a fi ring program
- 20 ‹ Designing and starting your own fi ring program
- 22 ‹ View function (soldering)
- 22 ‹ Entering standby mode
- 22 ‹ Fast cooling or manual fast cooling
- 23 7 Maintenance and cleaning
- 23 ‹ Lifting plate maintenance
- 23 ‹ Replacing the fi ring mouthful
- 23 ‹ Vacuum pump maintenance
- 24 8 Calibration using a silver wire test
- 25 ‹ Calibration program
- 26 9 Error messages and troubleshooting
- 27 ‹ Power failure
- 28 10 Pre-defi ned programs
- 29 11 Disposal
- 30 12 EC Declaration of Conformity