Multi-function Input Selection. Omron SYSDRIVE MX2 SERIES

5-3 Input/Output Terminals

5-3 Input/Output Terminals

The following explains the Inverter's input/output signals.

5

Multi-function Input Selection

The following functions can be allocated to any of multi-function input terminals S1 to S7/EB to operate each function that has been set.

Terminals S1 to S7/EB correspond to C001 to C007.

You can select NO- or NC-contact input for each multi-function input.

The same function cannot be allocated to multiple multi-function input terminals. If the same function was allocated to multiple functions by mistake, the terminal to which the function was allocated last becomes effective. no is allocated to all terminals to which the function was allocated earlier, and their functions are disabled.

After allocating functions to terminals S1 to to S7/EB, make sure that the function settings have been stored.

Parameter

No.

C001 to C007

14

15

16

18

19

09

11

12

13

Data

03

04

05

06

00

01

02

07

08

Description Reference item Page

FW: Forward

RV: Reverse

CF1: Multi-step speed 1

RUN Command Selection

CF2: Multi-step speed 2

CF3: Multi-step speed 3

CF4: Multi-step speed 4

JG: Jogging

Multi-step Speed Operation

Function (Binary)

Jogging Operation

DB: External DC injection braking External DC Injection Braking

SET: Motor 2 Control Motor 2 Control Function

2CH: 2-step acceleration/ deceleration

2-step Acceleration/deceleration

Function

FRS: Free-run stop

EXT: External trip

USP: USP function

CS: Commercial switch

SFT: Soft lock

FV/FI: Analog input switch

RS: Reset

TH: PTC thermistor thermal protection

Free-run Stop

External Trip

Power Recovery Restart

Prevention Function

Commercial Switching

Soft Lock

Analog Input

Reset

Thermistor Trip Function

5-22

5-64

5-59

5-135

5-54

5-66

5-103

5-120

5-105

5-79

5-84

5-37

5-100

5-120

SYSDRIVE MX2 Series USER'S MANUAL (3G3MX2-Axxxx)

5-29

5-3 Input/Output Terminals

Parameter

No.

C001 to C007

59

60

61

62

65

53

56

57

58

40

41

42

44

46

34

35

36

37

38

29

31

32

33

39

47

50

51

52

Data

20

21

22

23

24

27

28

Description Reference item Page

STA: 3-wire start

STP: 3-wire stop

F/R: 3-wire forward/reverse

PID: PID disabled

PIDC: PID integral reset

UP: UP/DWN function accelerated

DWN: UP/DWN function decelerated

UDC: UP/DWN function data clear

OPE: Forced operator

SF1: Multi-step speed bit 1

SF2: Multi-step speed bit 2

SF3; Multi-step speed bit 3

SF4: Multi-step speed bit 4

SF5: Multi-step speed bit 5

SF6: Multi-step speed bit 6

SF7: Multi-step speed bit 7

OLR: Overload limit switching

3-wire Input Function

PID Function

Remote Operation Function

Forced Digital Operator Function

5-85

Multi-step Speed Operation

Function (Bit)

Overload Limit/Overload

Warning

5-56

5-73

5-71

5-65

5-114

TL: Torque limit enabled/disabled

TRQ1: Torque limit switching 1

TRQ2: Torque limit switching 2

BOK: Brake confirmation

LAC: LAD cancel

PCLR: Position deviation clear

ADD: Frequency addition

F-TM: Forced terminal block

ATR: Torque reference input permission

KHC: Integrated power clear

Torque Limit Function

Brake Control Function

Acceleration/Deceleration

Function

5-153

5-142

5-24

Simple Position Control Function 5-157

Frequency Addition Function

5-71

Forced Terminal Block Function

5-85

Torque Control

Integrated Power Monitor

5-155

5-7

Reserved.

AHD: Analog command held

−

Analog Command Hold Function

−

5-39

5

SYSDRIVE MX2 Series USER'S MANUAL (3G3MX2-Axxxx)

5-30