advertisement
PowerSDR mRX PS IP address
Make a note of your ANAN Transceivers unique MAC address since this will be useful if you need to debug a network problem in the future.
Note: Make sure you have selected the proper radio model from the selections on the LEFT side of the
Hardware Configuration box. Failure to do so will result in an improper set of menu options and displays.
The Static IP Addresses are available to point your instance of OpenHPSDR/PowerSDR/OpenHPSDR to a particular Apache Transceiver. There may be several Transceivers on your LAN and the Static IP address is a convenience for pointing this software to a particular unit – where each unit has it's own IP address.
Setup ---> General tab ---> Hardware Config tab, the Radio Model should have ANAN Transceiver selected.
Connection Type “
ANAN
” and “
Full Network Discovery
” should both be checked. In the “
Region”
, select the
Country in which you reside.
The ANAN IP address and Firmware version number in the green box highlighted above will be set automatically by your network router DHCP server, or if connected directly to your PC, the IP address will be assigned by the
“APIPA” process – WHICH MAY TAKE UP TO SEVERAL MINUTES TO ASSIGN AN IP ADDRESS.
If your LAN is properly configured, the ANAN Transceiver board IP ADDRESS and MAC ADDRESS should be automatically be detected and assigned. An incorrect default value is 169.254.1XX.XXX.
OpenHPSDR/PowerSDR™ will display the currently assigned IP address and MAC address of the ANAN
Transceiver Hermes board if the LAN connection is properly connected and configured. If the ANAN
Transceiver IP ADDRESS remains 0.0.0.0 then you must determine if OpenHPSDR/PowerSDR and your PC network connection is operating correctly. Some typical problems could be that the Ethernet connection to your PC or LAN connector is disabled in Windows. The Ethernet connector may not be properly seated in your PC or Router. DHCP addressing must be properly enabled on your router. The new HPSDRProgrammer
V2 utility allows you to assign a STATIC IP ADDRESS if you wish.
Please see APIPA appendix of this document for more information.
Copyright Apache Labs © ANAN-8000DLE 28 15 March 2017
advertisement
Related manuals
advertisement
Table of contents
- 5 Apache Labs LLC, Inc. - Declarations of Conformity
- 5 Apache Labs Products CE and RTTE Certified
- 5 Heat Dissipation
- 5 Clarification CCS [60W]/ICAS [200W] operation
- 6 We are very proud of the 8000DLE Design Team
- 6 General Specifications:
- 6 Electrical Specifications:
- 6 Mechanical Specifications:
- 6 Receiver Specifications:
- 7 Transmitter Specifications:
- 7 Audio Connections:
- 7 Additional I/O Connections:
- 7 Ethernet Command and Control:
- 7 Noise Blankers:
- 8 Noise Reduction:
- 8 Minimized Latency:
- 8 Two phase synchronous ADCs
- 8 Front Panel LCD display
- 9 PureSignal Pre-Distortion:
- 9 Ultra-Rugged LDMOS 50vdc
- 11 Introduction
- 11 Minimum Requirements
- 12 Suitable routers or LAN Network switches
- 12 Ethernet Connection
- 13 Simple network setup
- 13 Recommended Software
- 14 ANAN-8000DLE Front Panel
- 15 LCD Front Panel display Power and Self Test
- 15 LCD microcomputer sensors
- 16 ANAN-8000DLE Back Panel
- 17 ANAN-8000DLE back panel Antennas
- 18 ANAN-8000DLE back panel LAN/Phones/Mic/Key
- 19 ANAN-8000DLE back panel XVTR RF1
- 20 Hardware Setup
- 21 Software Setup
- 22 Download the stable release version
- 23 Windows Installation
- 24 Wisdom optimization calculation
- 25 PowerSDR mRX PS Installation Wizard
- 26 PowerSDR mRX PS main window display
- 27 PowerSDR mRX PS Setup Menu
- 28 PowerSDR mRX PS IP address
- 29 PowerSDR mRX PS
- 30 Connecting a suitable Microphone
- 31 MIC Adapters
- 33 Selecting Transmit Profile
- 33 Adjusting mic gain
- 35 Tune
- 35 VOX
- 35 Transmit Filter
- 36 HPF/LPF Filters and switching
- 37 Antenna Control menu allows you to control the following options:
- 38 Sample Rate
- 39 1 Iambic A/B
- 40 Paddle Connection
- 40 CWU/CWL
- 41 Select Operating Frequency
- 41 Set Drive Level
- 42 Break-in Delay
- 43 Sidetone Level
- 44 Antenna
- 44 Note the Antenna Control menu allows you to control the following options:
- 45 Tuning
- 47 Tune/SWR/Output
- 48 PA Drive Level Calibration
- 49 PTT Input
- 49 FET
- 49 How to test your PTT Linear Amplifier circuit BEFORE connecting your Apache Transceiver.
- 49 Various Linear Amplifier Keying ISOLATION adapters are available
- 49 ALC
- 50 Various directional coupler models are available
- 50 VK6PH example OpenCollector BCD keying
- 52 How to Use PureSignal Adaptive Predistortion
- 55 PowerSDR Release github Webpage
- 56 Power SDR Download github version 3.3.11 webpage
- 57 Apache Labs International Support
- 57 Apache Yahoo Support Group
- 57 OpenHPSDR Group
- 57 Apache Service and Repair
- 57 Apache Schematics
- 57 Original 2013 Users Guide
- 58 Balanced Audio Input is not implemented in the current Apache Labs Transceivers.
- 58 Multiple independent .xml databases
- 59 Manual Calibration Procedure
- 60 Computer Performance
- 61 Warranty
- 61 IMPORTANT
- 62 MARS operation
- 62 APIPA Automatic Private IP Addressing
- 63 Apache Labs ANAN-8000DLE PCB (from brochure)
- 64 ANAN-8000DLE PA Filter PCB (from brochure)
- 65 ANAN-8000DLE PA and Filters (from brochure)
- 66 Apache Labs ANAN-8000DLE (from brochure)
- 67 Instructions to load independent versions on a single PC are summarized here:
- 68 Explanation of the bootloader normal operation
- 69 HPSDRBootloader 2.0.4.4 Utility
- 70 If you need a ByteBlaster
- 71 ByteBlaster firmware cabling
- 72 Install Arduino IDE
- 73 Download sketch:
- 73 Open Sketch with Arduino IDE
- 74 Add LCD display library:
- 74 Upload Sketch to 8000DLE
- 75 Start Arduino IDE