advertisement
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrenches and your own phillips screwdriver , rubber mallet , wire cutters , and needlenose pliers .
For help identifying the assembly hardware, see the drawings below. If a part is not in the parts bag, first check to see if it has been pre-assembled.
If a part is missing, call toll-free 1-888-533-1333.
1/2” Silver Screw
(48)–1
1/2” Ground Screw
(75)–1
3/4” Tek Screw (58)–8
3/4” Screw (2)–8
Crossbar Screw
(39)–2
3/4” Bolt (37)–6
Washer (38)–6
Wheel Nut (32)–2
3 1/2” Bolt (64)–2
1.
Make sure that the power cord is unplugged.
1
69
63
62
With the help of another person, carefully raise the
Uprights (69) to the vertical position. Insert one of the
Extension Legs (63) into the treadmill as shown. (Note: It may be helpful to tip the Uprights as you insert the
Extension Leg.) Make sure that the Warning Decal (62) is in the position shown.
Insert the other Extension Leg (63) in the same way.
6
2. With the help of another person, carefully lower the
Uprights (69) as shown. (Note: It may be helpful to place your foot on one of the Extension Legs [63] as you tip the Uprights.)
Make sure that the Extension Legs remain in the Uprights.
Attach each Extension Leg (63) with two 3/4” Tek
Screws (58).
Attach four Base Pads (57) with four 3/4” Tek Screws
(58) as shown. Note: One replacement Base Pad may be included. If a Base Pad becomes worn and needs to be replaced, use the replacement Base Pad.
With the help of another person, carefully raise the
Uprights (69) to the vertical position.
2
57
58
58
57
58
63
58
57
58
58
57
69
63
3. Attach the Storage Latch (29) to the left Upright (69) with two 3/4” Screws (2).
Do not overtighten the Screws.
3
29
69
2
4. Identify the Right Handrail (72), which has a large hole in the left side. Remove any ties from the bracket on the
Right Handrail and from the Wire Harness (42). Feed the
Wire Harness up into the bracket on the Right Handrail and out of the large hole in the left side. (Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the large hole.) Press a Handrail Cap (76) onto the lower end of the Right Handrail as shown.
Insert the bracket on the Right Handrail (72) into the top of the Right Upright (69) so the Handrail Cap (76) is resting against the Right Upright. Attach the Right Handrail and the Handrail Cap with
three 3/4” Bolts (37) and
three Washers (38) as shown. Firmly tighten the indi-
cated Bolt, but do not tighten the other Bolts yet.
Attach the Left Handrail (not shown) as described above.
Note: There is not a wire harness on the left side.
4
72
Large
Hole
Bracket
37
38
7
42
76
38
37
37
38
Tighten
69
5. Attach the end of the ground wire to the small hole in the side of the Right Handrail (72) with a Silver Ground
Screw (75).
5
75
Ground
Wire
72
6. Turn the Console Base (47) upside-down;
be careful not
to scratch the Console (43). Set the Crossbar (40) in the
Console Base, with the indicated small holes on top.
Attach the Crossbar (40) to the Console Base (47) with two
3/4” Screws (2).
Do not overtighten the Screws.
6
40
2
Small
Holes
2
47
43
7. Place the Console Base (47) on the Right Handrail (72) and the Left Handrail (not shown). Attach the Console
Base with four 3/4” Screws (2) (only two Screws are shown).
Do not overtighten the Screws.
Insert the Wire Harness (42) through the two indicated plastic ties on the Console Base (47). Next,
touch the
Right Handrail (72) to discharge any static. See the inset drawing. Find the 5-pin connector on the end of the
Wire Harness. Insert the connector into the red socket beneath the console.
The connector should slide easily
into the socket and snap into place. If the connector does not slide easily and snap into place, turn the connector and then insert it. Insert the 6-pin connector into the black socket beneath the console in the same way.
Make sure that the connectors and wires appear as shown in the inset drawing.
IF THE CONNECTORS ARE
NOT INSERTED PROPERLY, THE CONSOLE MAY BE
DAMAGED WHEN THE POWER IS TURNED ON.
7
2
47
42
Ties
72
43
42
5-pin
6-pin
8
8. Insert the excess Wire Harness (42) into the large hole in the side of the Right Handrail (72).
Securely tighten the plastic ties on the bottom of the Console Base (47) to
prevent the Wire Harness from slipping. Then, cut off the ends of the plastic ties.
Route the Wire Harness (42) through the indicated opening in the Console Base (47), and attach the Wire Cover
(44) to the Console Base with a 1/2” Silver Screw (48).
Do not overtighten the Silver Screw.
Tighten a Crossbar Screw (39) into the bracket on each
Upright (69) and into the Crossbar (40) (one one Screw is shown).
8
72
69
Ties
42
Opening
47
40
39
48
44
9. Attach a Wheel (66) to the inner side of each Extension
Leg (63) with a Wheel Bolt (64) and a Wheel Nut (32)
(only one Wheel is shown).
Do not overtighten the
Wheel Bolt. The Wheel should be able to spin freely.
Lift the treadmill frame (see HOW TO FOLD THE
TREADMILL FOR STORAGE on page 14), but do not latch it. Make sure that the frame is centered between the Handrails (not shown).
See step 4 and firmly
tighten the 3/4” Bolts (37). Then, lower the frame to the floor.
9
32
66
63
64
10.
Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the walking belt (see page 17). To protect the floor or carpet, place a mat under the treadmill.
9
advertisement
Related manuals
advertisement