advertisement
WHEEL SENSORS
WHEEL SENSORS
Removal and Installation
[TCS/ABS]
PFP:47910
EFS0067Z
A
B
–
LFIA0078E
CAUTION:
●
Be careful not to damage wheel sensor edge and sensor rotor teeth.
●
When removing the front or rear wheel hub assembly, first remove the wheel sensor from the assembly. Failure to do so may result in damage to the wheel sensor wires making the sensor inoperative.
CAUTION:
●
Pull out the wheel sensor, being careful to turn it as little as possible. Do not pull on the wheel sensor harness.
●
Installation should be performed while paying attention to the following, and then tighten mounting bolts and nuts to the specified torque.
Check if foreign objects such as iron fragments are adhered to the pick-up part of the sensor or to the inside of the hole for the wheel sensor, or if a foreign object is caught in the mating surface of the sensor rotor. If something wrong is found, fix it and then install the wheel sensor.
REMOVAL
1.
Remove wheel and tire using power tool.
2.
Disconnet wheel sensor harness connector and remove harness wire from attachment points.
3.
Remove wheel sensor bolt and wheel sensor.
INSTALLATION
Installation is in the reverse order of removal.
●
When installing wheel and tire, refer to WT-7, "Tire Rotation" .
G
H
I
J
K
L
M
C
D
E
BRC
Revision: May 2006
BRC-41
2007 Maxima
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 PRECAUTIONS
- 3 SIONER
- 3 Precautions for Brake System
- 3 Precautions When Using CONSULT-II
- 3 CHECK POINTS FOR USING CONSULT-II
- 4 Precautions for Brake Control
- 4 Precautions for CAN System
- 5 PREPARATION
- 5 Special Service Tool
- 5 Commercial Service Tools
- 6 SYSTEM DESCRIPTION
- 6 System Diagram
- 6 ABS Function
- 6 EBD Function
- 6 TCS Function
- 7 Wheel Sensors
- 7 Fail-Safe Function
- 7 ABS/EBD SYSTEM
- 7 TCS SYSTEM
- 8 Hydraulic Circuit Diagram
- 9 CAN COMMUNICATION
- 9 System Description
- 10 TROUBLE DIAGNOSIS
- 10 Accurate Repair
- 10 INTRODUCTION
- 11 WORK FLOW
- 12 CLARIFY CONCERN
- 12 EXAMPLE OF DIAGNOSIS SHEET
- 15 Schematic
- 16 Wiring Diagram — TCS
- 20 Basic Inspection
- 20 BRAKE PAD INSPECTION
- 20 AND BATTERY INSPECTION
- 20 LAMP INSPECTION
- 20 Warning Lamp and Indicator Timing
- 21 Control Unit Input/Output Signal Standard
- 21 REFERENCE VALUE FROM CONSULT-II
- 23 CONSULT-II Function (ABS)
- 23 CONSULT-II START PROCEDURE
- 23 SELF-DIAGNOSIS
- 25 DATA MONITOR
- 27 ACTIVE TEST
- 29 ITEMS
- 29 Wheel Sensor System Inspection
- 30 Engine System Inspection
- 31 ABS/TCS Control Unit Inspection
- 31 Solenoid Valve System Inspection
- 33 Stop Lamp Switch System Inspection
- 34 Inspection
- 35 CAN Communication System Inspection
- 35 Component Inspection
- 35 TCS OFF SWITCH
- 36 TROUBLE DIAGNOSES FOR SYMPTOMS
- 36 ABS Works Frequently
- 37 Unexpected Pedal Action
- 38 Long Stopping Distance
- 38 ABS Does Not Work
- 38 Pedal Vibration or ABS Operation Noise
- 39 tion Switch Is Turned On
- 39 Is Turned On
- 40 Vehicle Jerks During TCS Activation
- 41 WHEEL SENSORS
- 41 Removal and Installation
- 41 REMOVAL
- 41 INSTALLATION
- 42 SENSOR ROTOR
- 42 Removal and Installation
- 42 REMOVAL
- 42 INSTALLATION
- 43 ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
- 43 Removal and Installation
- 43 REMOVAL
- 43 INSTALLATION
- 45 PRECAUTIONS
- 45 SIONER
- 45 Precautions for Brake System
- 45 Precautions When Using CONSULT-II
- 45 CHECK POINTS FOR USING CONSULT-II
- 46 Precautions for Brake Control
- 46 Precautions for CAN System
- 48 PREPARATION
- 48 Special Service Tool
- 48 Commercial Service Tools
- 49 SYSTEM DESCRIPTION
- 49 System Components
- 49 ABS Function
- 49 EBD Function
- 50 TCS Function
- 50 VDC Function
- 51 Wheel Sensors
- 51 Fail-Safe Function
- 51 ABS/EBD SYSTEM
- 51 VDC/TCS SYSTEM
- 52 Hydraulic Circuit Diagram
- 53 CAN COMMUNICATION
- 53 System Description
- 54 TROUBLE DIAGNOSIS
- 54 Accurate Repair
- 54 INTRODUCTION
- 55 WORK FLOW
- 56 CLARIFY CONCERN
- 56 EXAMPLE OF DIAGNOSIS SHEET
- 57 Component Parts and Harness Connector Location
- 59 Schematic
- 60 Wiring Diagram — VDC
- 66 Basic Inspection
- 66 BRAKE PAD INSPECTION
- 66 AND BATTERY INSPECTION
- 66 AND VDC OFF INDICATOR LAMP INSPECTION
- 67 Warning Lamp and Indicator Timing
- 67 Control Unit Input/Output Signal Standard
- 67 REFERENCE VALUE FROM CONSULT-II
- 70 CONSULT-II Function (ABS)
- 70 CONSULT-II START PROCEDURE
- 70 SELF-DIAGNOSIS
- 73 DATA MONITOR
- 75 ACTIVE TEST
- 77 ITEMS
- 77 Wheel Sensor System Inspection
- 78 Engine System Inspection
- 79 ABS/TCS/VDC Control Unit Inspection
- 79 Steering Angle Sensor System Inspection
- 82 Inspection
- 84 Stop Lamp Switch System Inspection
- 85 Systems Inspection
- 86 Brake Fluid Level Switch System Inspection
- 87 CAN Communication System Inspection
- 87 Component Inspection
- 87 VDC OFF SWITCH
- 88 TROUBLE DIAGNOSES FOR SYMPTOMS
- 88 ABS Works Frequently
- 89 Unexpected Pedal Action
- 90 Long Stopping Distance
- 90 ABS Does Not Work
- 90 Pedal Vibration or ABS Operation Noise
- 91 tion Switch Is Turned On
- 91 Is Turned On
- 92 Vehicle Jerks During TCS/VDC Activation
- 93 ON-VEHICLE SERVICE
- 94 WHEEL SENSORS
- 94 Removal and Installation
- 94 REMOVAL
- 94 INSTALLATION
- 95 SENSOR ROTOR
- 95 Removal and Installation
- 95 REMOVAL
- 95 INSTALLATION
- 96 Removal and Installation
- 96 REMOVAL
- 96 INSTALLATION
- 98 STEERING ANGLE SENSOR
- 98 Removal and Installation
- 99 G SENSOR
- 99 Removal and Installation
- 99 REMOVAL
- 99 INSTALLATION