advertisement
G SENSOR
G SENSOR
Removal and Installation
REMOVAL
1.
Remove center console. Refer to IP-17, "Front Center Console" .
2.
Disconnect harness connector.
3.
Remove attaching nuts and remove yaw rate/side/decel G sensor.
CAUTION:
●
Do not drop or strike the yaw rate/side/decel G sensor.
●
Do not use power tools to remove or install yaw rate/side/ decel G sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
●
Do not drop or strike the yaw rate/side/decel G sensor.
[VDC/TCS/ABS]
PFP:47930
EFS004HV
A
B
C
D
E
PFIA0450E
BRC
I
J
G
H
K
L
M
Revision: May 2006
BRC-99
2007 Maxima
G SENSOR
[VDC/TCS/ABS]
Revision: May 2006
BRC-100
2007 Maxima
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 PRECAUTIONS
- 3 SIONER
- 3 Precautions for Brake System
- 3 Precautions When Using CONSULT-II
- 3 CHECK POINTS FOR USING CONSULT-II
- 4 Precautions for Brake Control
- 4 Precautions for CAN System
- 5 PREPARATION
- 5 Special Service Tool
- 5 Commercial Service Tools
- 6 SYSTEM DESCRIPTION
- 6 System Diagram
- 6 ABS Function
- 6 EBD Function
- 6 TCS Function
- 7 Wheel Sensors
- 7 Fail-Safe Function
- 7 ABS/EBD SYSTEM
- 7 TCS SYSTEM
- 8 Hydraulic Circuit Diagram
- 9 CAN COMMUNICATION
- 9 System Description
- 10 TROUBLE DIAGNOSIS
- 10 Accurate Repair
- 10 INTRODUCTION
- 11 WORK FLOW
- 12 CLARIFY CONCERN
- 12 EXAMPLE OF DIAGNOSIS SHEET
- 15 Schematic
- 16 Wiring Diagram — TCS
- 20 Basic Inspection
- 20 BRAKE PAD INSPECTION
- 20 AND BATTERY INSPECTION
- 20 LAMP INSPECTION
- 20 Warning Lamp and Indicator Timing
- 21 Control Unit Input/Output Signal Standard
- 21 REFERENCE VALUE FROM CONSULT-II
- 23 CONSULT-II Function (ABS)
- 23 CONSULT-II START PROCEDURE
- 23 SELF-DIAGNOSIS
- 25 DATA MONITOR
- 27 ACTIVE TEST
- 29 ITEMS
- 29 Wheel Sensor System Inspection
- 30 Engine System Inspection
- 31 ABS/TCS Control Unit Inspection
- 31 Solenoid Valve System Inspection
- 33 Stop Lamp Switch System Inspection
- 34 Inspection
- 35 CAN Communication System Inspection
- 35 Component Inspection
- 35 TCS OFF SWITCH
- 36 TROUBLE DIAGNOSES FOR SYMPTOMS
- 36 ABS Works Frequently
- 37 Unexpected Pedal Action
- 38 Long Stopping Distance
- 38 ABS Does Not Work
- 38 Pedal Vibration or ABS Operation Noise
- 39 tion Switch Is Turned On
- 39 Is Turned On
- 40 Vehicle Jerks During TCS Activation
- 41 WHEEL SENSORS
- 41 Removal and Installation
- 41 REMOVAL
- 41 INSTALLATION
- 42 SENSOR ROTOR
- 42 Removal and Installation
- 42 REMOVAL
- 42 INSTALLATION
- 43 ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
- 43 Removal and Installation
- 43 REMOVAL
- 43 INSTALLATION
- 45 PRECAUTIONS
- 45 SIONER
- 45 Precautions for Brake System
- 45 Precautions When Using CONSULT-II
- 45 CHECK POINTS FOR USING CONSULT-II
- 46 Precautions for Brake Control
- 46 Precautions for CAN System
- 48 PREPARATION
- 48 Special Service Tool
- 48 Commercial Service Tools
- 49 SYSTEM DESCRIPTION
- 49 System Components
- 49 ABS Function
- 49 EBD Function
- 50 TCS Function
- 50 VDC Function
- 51 Wheel Sensors
- 51 Fail-Safe Function
- 51 ABS/EBD SYSTEM
- 51 VDC/TCS SYSTEM
- 52 Hydraulic Circuit Diagram
- 53 CAN COMMUNICATION
- 53 System Description
- 54 TROUBLE DIAGNOSIS
- 54 Accurate Repair
- 54 INTRODUCTION
- 55 WORK FLOW
- 56 CLARIFY CONCERN
- 56 EXAMPLE OF DIAGNOSIS SHEET
- 57 Component Parts and Harness Connector Location
- 59 Schematic
- 60 Wiring Diagram — VDC
- 66 Basic Inspection
- 66 BRAKE PAD INSPECTION
- 66 AND BATTERY INSPECTION
- 66 AND VDC OFF INDICATOR LAMP INSPECTION
- 67 Warning Lamp and Indicator Timing
- 67 Control Unit Input/Output Signal Standard
- 67 REFERENCE VALUE FROM CONSULT-II
- 70 CONSULT-II Function (ABS)
- 70 CONSULT-II START PROCEDURE
- 70 SELF-DIAGNOSIS
- 73 DATA MONITOR
- 75 ACTIVE TEST
- 77 ITEMS
- 77 Wheel Sensor System Inspection
- 78 Engine System Inspection
- 79 ABS/TCS/VDC Control Unit Inspection
- 79 Steering Angle Sensor System Inspection
- 82 Inspection
- 84 Stop Lamp Switch System Inspection
- 85 Systems Inspection
- 86 Brake Fluid Level Switch System Inspection
- 87 CAN Communication System Inspection
- 87 Component Inspection
- 87 VDC OFF SWITCH
- 88 TROUBLE DIAGNOSES FOR SYMPTOMS
- 88 ABS Works Frequently
- 89 Unexpected Pedal Action
- 90 Long Stopping Distance
- 90 ABS Does Not Work
- 90 Pedal Vibration or ABS Operation Noise
- 91 tion Switch Is Turned On
- 91 Is Turned On
- 92 Vehicle Jerks During TCS/VDC Activation
- 93 ON-VEHICLE SERVICE
- 94 WHEEL SENSORS
- 94 Removal and Installation
- 94 REMOVAL
- 94 INSTALLATION
- 95 SENSOR ROTOR
- 95 Removal and Installation
- 95 REMOVAL
- 95 INSTALLATION
- 96 Removal and Installation
- 96 REMOVAL
- 96 INSTALLATION
- 98 STEERING ANGLE SENSOR
- 98 Removal and Installation
- 99 G SENSOR
- 99 Removal and Installation
- 99 REMOVAL
- 99 INSTALLATION