- No category
advertisement
Hardware options installation
In this section
Introduction
If more than one option is being installed, read the installation instructions for all the hardware options and identify similar steps to streamline the installation process.
For HP-supported options, refer to the Quickspecs on the HP website
( http://www.hp.com/servers/proliant ).
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and
the internal system components to cool before touching them.
CAUTION: To prevent damage to electrical components, properly ground the server before beginning any installation procedure. Improper grounding can cause electrostatic discharge.
CAUTION: Before installing any options, power down the server to prevent damage to the server and the equipment ("
Power down the server " on page 5 ).
Processor option
For server-specific processor installation instructions, refer to the installation instructions included with the processor option kit.
CAUTION: To prevent possible server malfunction and damage to the equipment, do not mix processors of different types or speeds.
Optical drive option
For server-specific optical drive installation instructions, see the installation sheet included with the option kit.
Memory options
For server-specific memory installation guidelines, refer to the installation sheet included with the server.
Hardware options installation 11
PCI riser board option
The HP ProLiant DL140 and DL145 Generation 2 Servers support one optional PCI Express riser board.
For server-specific riser board installation instructions, see the installation instructions included with the riser board option kit.
The HP ProLiant DL140 Generation 3 Server supports up to two optional PCI-X riser boards. For serverspecific riser board installation instructions, see the installation instructions included with the riser board option kit.
PCI expansion board option
The HP ProLiant DL140 Generation 2 and Generation 3 and the HP ProLiant DL145 Generation 2 Servers can be configured with up to two PCI expansion boards. For server-specific expansion board installation instructions, see the installation sheet included with the server.
Hard drive options
For server-specific hard drive installation instructions, refer to the installation sheet included with the server.
Hard drive backplane options
For server-specific hard drive backplane installation instructions for the HP ProLiant DL140 Generation 3
Server, see the installation sheet included with the server.
Hardware options installation 12
advertisement
Related manuals
advertisement
Table of contents
- 1 HP ProLiant 100 Series Server User Guide
- 2 Notice
- 3 Contents
- 5 Operations
- 5 Power up the server
- 5 Power down the server
- 5 Access panel
- 7 Setup
- 7 Optional installation services
- 8 Optimum environment
- 8 Space and airflow requirements
- 8 Temperature requirements
- 9 Power requirements
- 9 Electrical grounding requirements
- 9 Rack warnings
- 10 Installing hardware options
- 10 Installing the server into the rack
- 10 Powering up and configuring the server
- 10 Installing the operating system
- 10 Registering the server
- 11 Hardware options installation
- 11 Introduction
- 11 Processor option
- 11 Optical drive option
- 11 Memory options
- 12 PCI riser board option
- 12 PCI expansion board option
- 12 Hard drive options
- 12 Hard drive backplane options
- 13 Software and configuration utilities
- 13 ROMPaq Utility
- 13 Lights-Out 100i Remote Management
- 13 Diagnostic tools
- 13 HP Insight Diagnostics
- 14 Keeping the system current
- 14 Drivers
- 14 Updating firmware
- 15 Troubleshooting
- 15 Common problem resolution
- 15 Loose connections
- 15 Service notifications
- 15 Problem diagnosis
- 16 Important safety information
- 16 Symbols on equipment
- 17 Warnings and cautions
- 18 Preparing the server for diagnosis
- 18 Symptom information
- 18 Diagnostic steps
- 19 Start diagnosis flowchart
- 19 General diagnosis flowchart
- 21 Power-on problems flowchart
- 23 POST problems flowchart
- 25 OS boot problems flowchart
- 26 Server fault indications flowchart
- 27 Hardware problems
- 28 Hardware problems
- 28 Power problems
- 29 Unknown problem
- 30 General hardware problems
- 31 Internal system problems
- 37 System open circuits and short circuits
- 38 External device problems
- 44 Contacting HP
- 44 Contacting HP technical support or an authorized reseller
- 44 Server information you need
- 48 Software tools and solutions
- 48 Introduction to software problems
- 49 Operating system updates
- 50 Restoring to a backed-up version
- 50 When to reconfigure or reload software
- 51 Linux operating systems
- 51 Application software problems
- 51 Firmware maintenance
- 51 Types of ROM
- 52 Flashing ROM
- 52 Current firmware versions
- 52 Updating firmware
- 53 Drivers
- 54 Battery replacement
- 55 Regulatory compliance notices
- 55 Regulatory compliance identification numbers
- 55 Federal Communications Commission notice
- 55 FCC rating label
- 56 Class A equipment
- 56 Class B equipment
- 56 Declaration of conformity for products marked with the FCC logo, United States only
- 57 Modifications
- 57 Cables
- 57 Canadian notice (Avis Canadien)
- 57 European Union regulatory notice
- 58 Disposal of waste equipment by users in private households in the European Union
- 58 Japanese notice
- 58 BSMI notice
- 59 Korean notice
- 59 Laser compliance
- 59 Battery replacement notice
- 60 Taiwan battery recycling notice
- 60 Power cord statement for Japan
- 61 Electrostatic discharge
- 61 Preventing electrostatic discharge
- 61 Grounding methods to prevent electrostatic discharge
- 62 Technical support
- 62 Before you contact HP
- 62 HP contact information
- 62 Customer Self Repair
- 70 Acronyms and abbreviations
- 74 Index