advertisement
Intel
®
Server Board S5000VSA TPS Functional Architecture
Considering board positioning, the Intel have USB_6 (J1E2) built on the board.
®
Server Board 5000SVA SATA 4DIMM SKU will not
The server board provides an ATI* ES1000 PCI graphics accelerator, along with 16MB of video
DDR SDRAM and support circuitry for an embedded SVGA video sub-system. The ATI*
ES1000 chip contains an SVGA video controller, clock generator, 2D and 3D engine, and
RAMDAC in a 272-pin PBGA. One 4 Mx16x4 bank DDR SDRAM chip provides 16 MB of video memory.
The SVGA sub-system supports a variety of modes, up to 1600 x 1200 resolution in 8 / 16 / 32 bpp modes under 2D, and up to 1024 x 768 resolution in 8 / 16 / 24 / 32 bpp modes under 3D.
It also supports both CRT and LCD monitors with up to 100 Hz vertical refresh rate.
Video is accessed using a standard 15-pin VGA connector found on the back edge of the server board.
You can disable on-board video using the BIOS Setup Utility or when an add-in video card is installed. The system BIOS also provides the option for dual video operation when an add-in video card is configured in the system.
The chip supports all standard IBM* VGA modes. The following table shows the 2D/3D modes supported for both CRT and LCD.
2D Mode
640x480
800x600
1024x768
1280x1024
1280x1024
1600x1200
1600x1200
Refresh Rate (Hz)
60, 72, 75, 90, 100
60, 70, 75, 90, 100
60, 72, 75, 90, 100
43, 60
70, 72
60, 66
76, 85
Table 5. Video Modes
8 bpp
Supported
Supported
Supported
Supported
Supported
Supported
Supported
2D Video Mode Support
16 bpp
Supported
24 bpp
Supported
Supported
Supported
Supported
–
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Supported
32 bpp
Supported
Supported
Supported
Supported
Supported
Supported
–
3.3.2 Video Memory Interface
The memory controller sub-system of the ES1000 passes requests from the direct memory interface, VGA graphics controller, drawing coprocessor, display controller, video scalar, and hardware cursor. Requests are serviced in a manner that ensures display integrity and maximum CPU/coprocessor drawing performance.
The server board supports a 16 MB (4 MB x 16-bit x 4 banks) DDR SDRAM device for video memory. The following table shows the video memory interface signals:
Revision 1.6 Intel order number: D36978-008 17
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 12 Introduction
- 12 Chapter Outline
- 12 Server Board Use Disclaimer
- 13 Product Overview
- 13 Feature Set
- 14 Server Board Layout
- 15 Server Board Mechanical Drawing
- 17 Feature Set
- 18 Functional Architecture
- 18 5000V Controller Hub (MCH)
- 18 Processor Sub-system
- 20 Thermal Design Power of 35 W (Processor Population Rules)
- 21 Common Enabling Kit (CEK) Design Support
- 21 Memory Sub-system
- 22 Supported Memory
- 23 DIMM Population Rules
- 24 Memory Mirroring
- 24 Enterprise South Bridge (ESB2-E)
- 25 PCI Sub-system
- 25 PCI Express* Overview
- 25 PCI Express* Hot-Plug
- 26 SATA Support
- 26 SATA RAID
- 27 Embedded RAID Technology II Option ROM
- 27 Parallel ATA (PATA) Support)
- 27 Ultra ATA
- 27 IDE Initialization
- 27 USB 2.0 Support
- 28 Video Support
- 28 Video Modes
- 28 Video Memory Interface
- 29 Dual Video
- 30 Network Interface Controller (NIC)
- 30 Super I/O
- 31 Serial Ports
- 32 Removable Media Drives
- 32 Floppy Disk Controller (FDC)
- 32 Keyboard and Mouse Support
- 32 Wake-Up Control
- 33 Platform Management
- 33 Power Button
- 33 Sleep States Supported
- 33 S0 State
- 33 S1 State
- 34 S4 State
- 34 S5 State
- 34 Wakeup Events
- 34 Wakeup from S1 Sleep State
- 34 Wakeup from S3 Sleep State (BFAD Workstation Only)
- 34 Wakeup from S4 and S5 States
- 34 AC Power Failuar Recovery
- 35 PCI PM Support
- 35 Reset# Control
- 35 PCI Vaux
- 35 System Management
- 35 CPU Thermal Management
- 36 System Fan Operation
- 36 Light-Guided Diagnostics – System Status and FRU LEDs
- 38 Connector / Header Locations and Pin-outs
- 38 Board Connectors
- 38 Power Connectors
- 39 Control Panel Connector
- 40 I/O Connectors
- 40 VGA Connector
- 40 NIC Connectors
- 41 ATA-100 Connector
- 42 SATA Connectors
- 42 Serial Port Connectors
- 43 Keyboard and Mouse Connector
- 43 USB Connector
- 44 Fan Headers
- 45 Jumper Block Settings
- 45 Recovery Jumper Blocks
- 46 BIOS Select Jumper
- 46 Other Configuration Jumpers
- 47 Light-Guided Diagnostics
- 47 5-Volt Standby LED
- 47 Fan Fault LEDs
- 47 System ID LED, System Status LED, and POST Diagnostic LEDs
- 47 DIMM Fault LEDs
- 48 Processor Fault LEDs
- 49 Power and Environmental Specifications
- 49 Server Board S5000VSA Design Specifications
- 49 Processor Power Support
- 50 Power Supply Specifications
- 50 Output Power / Currents
- 51 Grounding
- 51 Standby Outputs
- 51 Remote Sense
- 51 Voltage Regulation
- 52 Dynamic Loading
- 52 Capacitive Loading
- 53 Closed Loop Stability
- 53 Common Mode Noise
- 53 Ripple / Noise
- 53 Timing Requirements
- 55 Residual Voltage Immunity in Standby Mode
- 56 Regulatory and Certification Information
- 56 Product Regulatory Compliance
- 56 Product Safety Compliance
- 57 Product EMC Compliance – Class A Compliance
- 57 Certifications / Registrations / Declarations
- 57 Product Ecology Requirements
- 59 Product Regulatory Compliance Markings
- 61 Electromagnetic Compatibility Notices
- 61 FCC Verification Statement (USA)
- 62 ICES-003 (Canada)
- 62 Europe (CE Declaration of Conformity)
- 62 VCCI (Japan)
- 63 BSMI (Taiwan)
- 63 RRL (Korea)
- 63 CNCA (CCC-China)
- 64 Appendix A: Integration and Usage Tips
- 65 Appendix B: Sensor Tables
- 68 Appendix C: POST Code Diagnostic LEDs
- 72 Glossary
- 75 Reference Documents