advertisement
12 Technical data
12 Technical data
12.1
BFS 735
Designation
Item no.
Max. width
Max. cutting depth
Peripheral speed with cutting blade 350 mm
Operating speed of cutting blade
Length (guide wheel folded up)
Width
Height
Weight
Min. cutting blade diameter
Max. cutting blade diameter
Center bore of cutting blade
Nominal power
Nominal speed
Water tank capacity
Storage temperature range
Operating temperature range
Sound pressure level L pA
Standard
Sound power level L
WA measured guaranteed
Unit
mm (in) cm (in) m/s
(ft/s) rpm mm (ft) mm (ft) mm (ft) kg (lb) mm (in) mm (in) mm (in) kW rpm l (gal)
°C (°F)
°C (°F) dB(A) dB(A)
100_0304_td_0009.fm
53
BFS 735
5100009932
12 (0.5)
12 (4.7)
46,0 (150.9)
2500
830 (32,7)
488 (19.2)
880 (34.6)
68 (149.9)
350 (14)
350 (14)
25,4 (1)
3,7
3600
20 (5.3)
-30 – +50 (-22 – +122)
-15 – +40 (-5 – +104)
84
DIN EN 13862
100
103
12 Technical data
Designation
Standard
Vibration total value a hv
Standard
Uncertainty of measurement of vibration total value a hv
Unit
m/s
2
(ft/s
2
) m/s
2
(ft/s
2
)
BFS 735
DIN EN 13862
4,9
DIN EN 13862
1,5
54
100_0304_td_0009.fm
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 2.1 Means of representation for this operator's manual
- 7 2.2 Wacker Neuson representative
- 7 2.3 Described machine types
- 8 2.4 Identification of the machine
- 9 3.1 Principle
- 12 3.2 Qualification of the operating personnel
- 13 3.3 Protective gear
- 14 3.4 Transport
- 16 3.5 Operating safety
- 18 3.6 Safety during the operation of combustion engines
- 21 3.7 Safety during floor saw operation
- 23 3.8 Maintenance
- 25 3.9 Safety devices
- 29 6.1 Application
- 29 6.2 Maximum permissible tilt
- 30 6.3 Functional description
- 31 6.4 General instructions for use for diamond-edged cutting blades
- 33 8.1 Adjusting the handle
- 33 8.2 Adjusting the guide wheel
- 34 Adjusting the guide wheel
- 34 Aligning the guide wheel
- 34 8.3 Cutting depth setting
- 34 8.4 Depth of cut indicator
- 35 8.5 Water tank
- 35 8.6 Parking brake
- 36 8.7 Assembling the cutting blade
- 36 Checking a new cutting blade
- 36 Proceed as follows for the assembly of the cutting blade
- 37 8.8 Disassembling the cutting blade
- 37 Proceed as follows for the disassembly of the cutting blade
- 38 8.9 Checking the motor before starting
- 38 Engine oil
- 38 Air cleaner
- 39 8.10 Starting the engine
- 40 8.11 Operating the engine
- 41 8.12 Turning off the engine
- 42 9.1 Maintenance schedule
- 43 9.2 Checking engine oil level
- 44 9.3 Changing the engine oil
- 45 9.4 Cleaning the air cleaner
- 45 9.5 Cleaning the filter cup
- 46 9.6 Idle setting
- 47 9.7 Tightening the belt
- 48 9.8 Changing the belt
- 49 9.9 Checking the spark plug
- 50 10.1 Parking brake
- 53 12.1 BFS
- 55 12.2 BFS
- 57 12.3 BFS
- 59 12.4 BFS
- 61 12.5 Combustion engine