<b>Initial Setup</b>. Pioneer VSX-LX303

SN29402804_VSX-932_BAS_En_1701XX.book 21 ページ ２０１７年２月３日　金曜日　午前９時３１分

> Before Start > Part Names > Install > Initial Setup > Playback

Initial Setup with Auto Start-up Wizard

1

2 3

INPUT

TV

Initial Setup Starts Automatically

When you turn the unit on for the first time after purchasing it, Initial Setup is automatically shown on the TV to enable you to make settings required for startup using simple operations following onscreen guidance.

1. Switch the input on the TV to that assigned to the unit.

2. Put batteries into the remote controller of this unit.

3. Press Í on the remote controller to turn the unit on.

4. Select the item with the cursors of the remote controller and press ENTER (a) to confirm your selection. To return to the previous screen, press (b).

a b

0 If you terminate the procedure on the way or want to change a setting made during Initial Setup, press on the remote controller, and from the Home select "System

Setup" - "Miscellaneous" - "Initial Setup", and press

ENTER.

∫ 1. Full Auto MCACC

Place the supplied speaker setup microphone in the listening position, measure the test tones emitted by the speakers, then the unit automatically sets the optimum volume level for each speaker, the crossover frequencies, and the distance from the listening position. This also automatically adjusts the equalizers for the speakers and enables correction of distortion caused by the acoustic environment of the room.

21

SN29402804_VSX-932_BAS_En_1701XX.book 22 ページ ２０１７年２月３日　金曜日　午前９時３１分

> Before Start > Part Names > Install > Initial Setup > Playback

22

0 Calibration takes between 3 and 12 minutes to be completed. The speakers emit the test tone at high volume during measurement, so be careful of your surroundings. Keep the room as quiet as possible during measurement.

0 If you have connected a subwoofer, check the power and volume of the subwoofer. Set the subwoofer volume to more than halfway.

0 If the power of this unit suddenly turns off, the wires in the speaker cables may have touch the rear panel or other wires and tripped the protection circuit. Twist the wires again properly and make sure they do not stick out of the speaker terminals when connecting.

1. Place the supplied speaker setup microphone in the listening position, and connect to the MCACC SETUP

MIC jack on the main unit.

MCACC

SETUP MIC

When putting the speaker setup microphone on a tripod, refer to the illustration when putting it in place.

2. Select the connected speaker configuration.

The image on the screen changes as you choose the number of channels in "Speaker Channels", so refer to it when performing the settings.

3. Test tones are emitted by the speakers, and firstly the unit detects the speakers connected and the noise in the environment.

4. After the results of the above measurements are displayed, select "Next", press ENTER on the remote controller, and the test tones are emitted again, and the unit automatically makes settings such as the optimum volume level and the crossover frequency.

5. When the measurement is completed, the measurement result is displayed. Press the cursors  / on the remote controller to check the settings. Press ENTER when "Save" is selected to save the settings.

6. Disconnect the speaker setup microphone.

∫ 2. Source Connection

Check that each input source is connected correctly. Follow the guidance, select the input you want to confirm, start play of the selected player, and confirm that the images appear on the TV and that sound is played.

∫ 3. Network Connection

Set up Wi-Fi connection with an access point such as a wireless LAN router. There are the following two methods of connecting by Wi-Fi:

"Scan Networks": Search for an access point from this unit. Find out the SSID of the access point beforehand.

"Use iOS Device (iOS7 or later)": Share the iOS device's

Wi-Fi settings with this unit.

If you select "Scan Networks", there are a further two choices of connection method. Check the following.

"Enter Password": Enter the password (or key) of the access point to connect.

"Push Button": If the access point has an automatic connection button, you can connect without entering a password.

0 If the SSID of the access point is not displayed, then in the screen listing the SSIDs, select "Other..." with the cursor on the remote controller and press ENTER, then follow the onscreen instructions.

Keyboard Input

To switch between upper and lower case, select "A/a" on the screen and press ENTER. To select whether to mask the password with "½" or display it in plain text, press +Fav on the remote controller. Press CLEAR to delete all the input characters.

0 A confirmation screen asking you to agree to the privacy policy is displayed during network setting. Select

"Accept" and press ENTER to indicate agreement.

∫ 4. Audio Return Channel

If you have connected a TV that supports ARC, select

"Yes". This unit's ARC setting turns on and you can listen to the TV's audio through this unit.