advertisement
Startup and Basic Operation
Frequency Measurement
The frequency measurement terminals are located in the
E
module.
Required settings Options/description
Quantity
Funct/Port
Freq.
E: f(meas)
Also check the
Unit
setting.
MC5-IS compares the external potential against an adjustable reference voltage
(
Trigger Level
, range: -1 … +15 V) when measuring the frequency.
T / C I N T . R J
T / C , L o w V R , R T D
4 w m e a s
V , ,
H A R T
T / C
W I R E S
O N L Y m e a s / s i m
S E N S O R M E A S U R E & S I M U L A T E
3 w m e a s
U o : 1 6 V
I o : 2 4 m A
P o : 1 4 5 m W
O U T P U T
E T
V , ,
M E A S U R E
m e a s / s i n k
L o w V
46
Next…
Switch State Sensing on page 43
Pulse Counting on page 47
Frequency Generation on page 62
Calibration, see Part D.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 8 About This Manual
- 9 Typographical Conventions
- 9 Unpacking and Inspection
- 10 Connections
- 11 The Upper Panel
- 12 the Left Side of MC5-IS
- 12 The Front Panel
- 15 Memory
- 16 Batteries
- 17 the Charging Procedure
- 18 the Battery Pack
- 19 Support for Table Top Use
- 19 the Neck Support Strap
- 20 General Description
- 20 Startup Procedure
- 21 Basic Mode
- 21 Maintenance
- 21 Calibration Mode
- 22 Help Function
- 23 The User Interface
- 23 The Status Bar
- 24 The Function Key Bar
- 24 Menus
- 25 The Display Area
- 29 Hardware Modules/Options
- 30 Other Connectable Devices
- 30 Firmware Options
- 31 Ex Information and Approvals
- 32 Safety Precautions and Warnings
- 32 General Warnings
- 33 of Electrical Modules (E and ET)
- 33 Pressure Measurement
- 34 High Pressure
- 35 Firmware Update
- 35 Recalibrating MC5-IS
- 35 The Battery Charger
- 36 Cleaning MC5-IS
- 36 Junction Module
- 38 Startup Procedure
- 39 Basic Mode, Defined
- 43 Pressure Measurement
- 43 Using Internal Modules
- 43 Using External Modules
- 44 Zeroing a Pressure Module
- 45 Current Measurement
- 46 Voltage Measurement
- 46 Measuring Low Voltages
- 47 Measuring Voltages up to ±30 V
- 48 Resistance Measurement
- 49 Switch State Sensing
- 50 Limit Switch Test
- 50 Performing the Limit Switch Test
- 52 Frequency Measurement
- 53 Pulse Counting
- 54 RTD Measurement (Temperature)
- 55 Measurement (Temperature)
- 55 Internal Reference Junction
- 55 External Reference Junction
- 58 Minimum value
- 58 Maximum value
- 58 Min/Max value
- 58 Rate of Change
- 59 Special Filtering and Resolution
- 59 Deviation Measurement
- 60 Two Ports Simultaneously
- 60 Difference Measurement
- 61 Redundant Measurement
- 62 General
- 63 the Generated/Simulated Signal
- 64 Current Sink
- 64 output terminals
- 66 Voltage Generation
- 66 between +10 V and -2.5 V
- 66 Low Voltage Generation
- 68 Frequency Generation
- 69 Pulse Generation
- 70 RTD and Resistance Simulation
- 71 Thermocouple Simulation
- 71 Internal Reference Junction
- 71 External Reference Junction
- 73 Configuration Window
- 74 Stepping
- 75 Ramping
- 80 Settings
- 82 Setting Time and Date
- 83 Display Mode Settings
- 84 Scaling
- 85 Displaying Error Values
- 86 Transmitter/Switch Simulation
- 87 Transmitter Simulation
- 88 Switch Simulation
- 89 Data Logging
- 89 General
- 89 Configuring
- 90 Starting the Data Log
- 91 Viewing the Results
- 91 a Personal Computer
- 93 Measuring Pressure
- 93 General
- 93 Pressure Type
- 94 their Naming Conventions
- 94 Square Rooting
- 95 Connections and Troubleshooting
- 95 Internal Reference Junction
- 96 External Reference Junction
- 98 Error situations
- 99 RTD Measurement, Connections
- 99 4-wire System
- 99 3-wire System
- 100 Using a Compensation Loop
- 100 2-wire System
- 101 to a Test Diode, Connections
- 102 Parallel Functions in MC5-IS
- 105 Phases of Instrument Calibration
- 106 As Found Calibration
- 106 Adjustment
- 107 As Left Calibration
- 108 Input/Output Signal Combinations
- 110 to Be Calibrated
- 111 The Instrument Window
- 112 Using MC5-IS
- 114 About Automatic Calibration
- 114 About Manual Calibration
- 115 Examples of Instrument Calibration
- 116 Pressure Transmitters
- 118 Temperature Sensors
- 120 Recorders
- 122 Electrical Limit Switches
- 124 Instrument Adjustment
- 125 Adding New Instruments
- 126 Editing Instrument Data
- 126 General Data Page
- 127 Instrument Input Page
- 127 Instrument Output Page
- 128 Calibration Settings Page
- 129 Calibration Instructions Page
- 129 Deleting Instruments
- 131 Calibration Result Windows
- 131 Calibration Run is Viewed
- 131 Deleting Calibration Results
- 135 MC5-IS and HART
- 136 Calibration Database Software
- 136 External Supply
- 137 Test Diode Connections
- 137 a Hart Communicator
- 139 Connecting to a HART Instrument
- 140 HART Instrument
- 140 Device Information
- 141 Device Settings
- 141 in Basic Mode
- 143 MC5-IS’ Instrument Database
- 144 to be Calibrated
- 145 The Calibration Procedure
- 145 in Calibration Mode
- 150 (INT-IS & EXT-IS)
- 151 Module (ET)
- 151 and Simulation
- 152 Module (RJ)
- 153 Electrical Module (E)
- 155 General
- 155 Installing MC5 Datalog Viewer
- 155 Communication Settings
- 155 File Management
- 155 Transferring data from MC
- 156 Saving Data on Hard Disk
- 156 Opening Existing Data Files
- 156 Importing and Exporting
- 156 Other Utilities
- 156 Chart Properties
- 157 Channel Properties
- 157 Zooming
- 157 Printing the Graph