- No category
advertisement
Installing and Configuring the
Seehau Software
Installing the Software
To install the Seehau software, do the following:
1.
Locate your Seehau CD and insert the CD into your CD ROM drive. The installation process will start automatically.
Note
If the installation does not start automatically, your Windows
Autorun feature is probably disabled. You will then need to select
Start/Run/Browse and navigate to the CD root directory. Double-click
Autorun.exe.
2.
Follow the instructions that appear on your screen.
3.
If you wish to add an icon to your desktop, use Windows Explorer to find the file Seehau.exe
located in the C:/Nohau/Seehau16 subdirectory.
4.
Right-click on the file, click the Create Shortcut option. Drag the shortcut to your desktop.
Rename the icon as desired.
Configuring Seehau Software
When first started, Seehau loads a configuration file called Startup.bas. This file is created by the
Seehau Configuration Program and stores Startup.bas in the following default subdirectory:
C:\Nohau\Seehau16\Macro.
The Seehau software automatically starts Seehau Config if it does not find the startup file.
You do not need to have the emulator connected to the PC to run the Seehau Config Program.
However, for the Seehau regular executable to operate properly, you do need the emulator connected with the jumpers properly set.
Get familiar with the emulator in stand-alone mode (not connected to a target system) or the demo mode before connecting to a target hardware system. The demo mode can be selected by doing the following: Select
Start/Programs/Seehau16/Demo
.
© ICE Technology
9
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 17 Downloading EMUL16/300–PC Product Documentation
- 18 Overview of the EMUL16/300–PC Emulator System
- 19 ISA Card Emulator (PC Plug-In)
- 19 High-Speed Parallel Box (HSP)
- 20 Emulator Parallel Cable (EPC)
- 20 Low Cost-Industry Standard Architecture (LC-ISA)
- 21 User Interface
- 21 Quick Start for Installing Your Emulator System
- 22 Quick Start for Installing the Hardware
- 24 Installing and Configuring the Seehau Software
- 24 Installing the Software
- 24 Configuring Seehau Software
- 25 Purchasers of Emulator and Trace Boards
- 26 Configuring Address Settings for the Emulator and Optional Trace Board
- 26 Information about Windows NT Installation
- 26 Known Device Driver Conflicts
- 27 Configuring Address Settings With Windows
- 27 Alternative Addressing
- 28 Configuring Address Settings With Windows NT
- 29 Alternative Addressing
- 30 Nohau16/300 Device Driver
- 31 Configuring Address Settings With Windows
- 35 Alternative Addressing
- 35 Nohau16/300 Device Driver With Windows
- 36 Installing and Configuring the Emulator Board
- 36 Installing the Emulator Board
- 37 I/O Address
- 38 Typical PC I/O Addresses
- 38 Factory and Alternate Settings
- 39 Setting Target Communication Rate Using BDM
- 39 Factory Settings
- 40 Emulator Board
- 41 Configuring the Emulator
- 44 Quick-Save Hardware Settings
- 46 Installing and Configuring the Trace Board
- 46 Overview
- 46 Installing the Trace Board
- 47 I/O Address
- 47 Installing the Trace Board With an HSP Box
- 47 Installing the Trace Board With a PC
- 48 Factory Settings
- 49 Bank Switch Jumpers
- 49 Configuring the Trace Board
- 52 Trace Setup Fields
- 53 Trigger Qualifier
- 54 Data Qualifier
- 56 Installing the Pod Boards
- 56 Overview
- 56 Pod Types
- 56 Connecting the Pod to the Target Board
- 57 How this Chapter is Organized
- 312 Important Notes About Pod Boards
- 312 Factory Configuration of Pod Boards
- 312 Remove Black Conducting Foam Before Using Your Pod
- 312 Features Common to All Pods
- 312 Background Debug Mode (BDM)
- 313 Background Debug Connector (BERG)
- 313 Using Just the BERG Connector
- 313 Indicator Lights
- 314 Disabling Resources
- 314 Removing and Installing the Controller
- 316 POD–16S
- 316 Overview
- 316 POD–16S2 LED Indicators
- 313 Header and Jumper Details
- 313 Using the Port Replacement Unit