- No category
advertisement
LED Indicators · 165
Overview · 165
POD–376 · 175
Configuration Options · 176
Header and Jumper Details · 177
16BIT · 177
AS · 178
BKPT / BERR / RST · 179
BNK0-3 · 177
CLK · 178
CS5 / CSE · 179
DS · 178
EXT PWR · 178
PLL · 179
ROM · 177
SER · 178
LED Indicators · 176
Overview · 175
Physical Dimensions · 175
POD–CM16Z1 · 87
Configuration Options · 88
Header and Jumper Details · 89
16BIT · 91
1M · 91
BERR / BKPT / RESET / DSI · 90
BNK0-3 · 90
CLK · 91
FCI · 89
PRU · 89
PWR · 89
ROM · 91
RXD · 89
SIZx · 91
LED Indicators · 87
Overview · 87
Q
Quick Start for Installing the Hardware · 7
Quick Start for Installing Your Emulator System · 6
R
Removing and Installing the Controller · 44
S
Shutting Down Seehau Software · 191
Starting Seehau · 185
Starting the Emulator and Seehau Software · 185
T
Technical Support · 1, 185 [email protected] · 1, 185
Time Program Examples · 187
Saving the Hardware Configuration · 190
Trace Memory Example · 197
W
WARNINGS · xi, 10, 30, 45, 48, 65, 80, 95, 105, 115,
125, 136, 145, 158, 167, 177, 225
Watching Data in Real-Time with Shadow RAM · 188
© ICE Technology
Index
–
7
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 17 Downloading EMUL16/300–PC Product Documentation
- 18 Overview of the EMUL16/300–PC Emulator System
- 19 ISA Card Emulator (PC Plug-In)
- 19 High-Speed Parallel Box (HSP)
- 20 Emulator Parallel Cable (EPC)
- 20 Low Cost-Industry Standard Architecture (LC-ISA)
- 21 User Interface
- 21 Quick Start for Installing Your Emulator System
- 22 Quick Start for Installing the Hardware
- 24 Installing and Configuring the Seehau Software
- 24 Installing the Software
- 24 Configuring Seehau Software
- 25 Purchasers of Emulator and Trace Boards
- 26 Configuring Address Settings for the Emulator and Optional Trace Board
- 26 Information about Windows NT Installation
- 26 Known Device Driver Conflicts
- 27 Configuring Address Settings With Windows
- 27 Alternative Addressing
- 28 Configuring Address Settings With Windows NT
- 29 Alternative Addressing
- 30 Nohau16/300 Device Driver
- 31 Configuring Address Settings With Windows
- 35 Alternative Addressing
- 35 Nohau16/300 Device Driver With Windows
- 36 Installing and Configuring the Emulator Board
- 36 Installing the Emulator Board
- 37 I/O Address
- 38 Typical PC I/O Addresses
- 38 Factory and Alternate Settings
- 39 Setting Target Communication Rate Using BDM
- 39 Factory Settings
- 40 Emulator Board
- 41 Configuring the Emulator
- 44 Quick-Save Hardware Settings
- 46 Installing and Configuring the Trace Board
- 46 Overview
- 46 Installing the Trace Board
- 47 I/O Address
- 47 Installing the Trace Board With an HSP Box
- 47 Installing the Trace Board With a PC
- 48 Factory Settings
- 49 Bank Switch Jumpers
- 49 Configuring the Trace Board
- 52 Trace Setup Fields
- 53 Trigger Qualifier
- 54 Data Qualifier
- 56 Installing the Pod Boards
- 56 Overview
- 56 Pod Types
- 56 Connecting the Pod to the Target Board
- 57 How this Chapter is Organized
- 312 Important Notes About Pod Boards
- 312 Factory Configuration of Pod Boards
- 312 Remove Black Conducting Foam Before Using Your Pod
- 312 Features Common to All Pods
- 312 Background Debug Mode (BDM)
- 313 Background Debug Connector (BERG)
- 313 Using Just the BERG Connector
- 313 Indicator Lights
- 314 Disabling Resources
- 314 Removing and Installing the Controller
- 316 POD–16S
- 316 Overview
- 316 POD–16S2 LED Indicators
- 313 Header and Jumper Details
- 313 Using the Port Replacement Unit