- Computers & electronics
- Audio & home theatre
- TV set-top boxes
- Satellite antennas
- KVH Industries
- TracVision M5
- Installation manual
Plan the Belowdecks Installation. KVH Industries TracVision M5
Add to My manuals30 Pages
KVH Industries TracVision M5 is an advanced satellite TV antenna system designed to provide exceptional television reception while on the move. With its ability to automatically acquire and track satellites, the TracVision M5 offers uninterrupted TV enjoyment, making it an ideal choice for marine and mobile applications.
advertisement
![Plan the Belowdecks Installation. KVH Industries TracVision M5 | Manualzz Plan the Belowdecks Installation. KVH Industries TracVision M5 | Manualzz](http://s3.manualzz.com/store/data/029456828_1-3c2c9e0b00875c02c78d92bf68fcce50-360x466.png)
3
Plan the Belowdecks Installation
Consider the following installation guidelines for the belowdecks equipment:
• Select a switchplate mounting location in a dry, well-ventilated area belowdecks away from any heat sources or salt spray.
• Be sure to leave enough room at the switchplate’s rear panel for connecting the cables and maintaining a service loop (see
Figure 6 for switchplate dimensions).
• The supplied data cable is 50 ft (15 m) long.
Be sure to locate the switchplate close enough to the antenna for the cable to reach, while allowing adequate slack for a service loop.
• (Circular and Sky Mexico only) The grounding block should be located within
45 ft (13 m) of the antenna, within 5 ft (1.5 m) of the primary receiver, and within 25 ft
(7.6 m) of a suitable vessel AC ground.
Figure 6: Switchplate Dimensions
4.39"
(111.5 mm)
2.16"
(54.9 mm)
2.96"
(75.2 mm)
Top View
Front View
Prepare the Switchplate Mounting Site
Once you have identified a suitable switchplate mounting site, follow these steps to prepare the site for installation.
NOTE: If you prefer, you may install the switchplate within a standard electrical panel instead.
a. Using the switchplate mounting template provided at the end of this manual, mark and cut out a hole in the mounting surface to accommodate the switchplate (see Figure 7).
b. Using the same template, mark the locations for the four switchplate mounting holes.
c. Drill a 3/32" (2.25 mm) hole at the four mounting hole locations. Later, you will mount the switchplate using four #6 screws.
Figure 7: Switchplate Mounting Holes Layout
3.82"
(97 mm)
.32" (8 mm)
3/32" ( 2.25 mm)
Mounting Hole (x4)
2.36"
(60 mm)
.16" (4 mm)
Panel Cutout
3.19"
(81 mm)
2.05"
(52 mm)
5
advertisement
Related manuals
advertisement
Table of contents
- 2 Installation Steps
- 2 Who Should Install the System?
- 2 Linear vs. Circular Systems
- 2 Technical Support
- 3 Inspect Parts and Get Tools
- 4 Plan the Antenna Installation
- 5 Plan the Belowdecks Installation
- 6 Prepare the Antenna Site
- 7 Remove the Restraints
- 8 Wire the Antenna
- 9 Mount the Antenna
- 10 Wire the Switchplate
- 11 Wire the Receiver(s) - Circular and Sky Mexico
- 12 Wire the Receiver(s) - Linear
- 13 Connect Power
- 14 Mount the Switchplate
- 15 Connect a Laptop to the Antenna
- 16 Select Satellites - Circular
- 17 Select Satellites - Linear
- 18 Enter Your Latitude & Longitude
- 19 Run Two Check Switch Tests
- 20 Set the LNB Skew Angle - Linear
- 21 Educate the Customer
- 22 Appendices
- 23 Wiring 3+ Receivers - Circular
- 24 Wiring 3+ Receivers - Sky Mexico
- 25 Satellite Library
- 26 Position Grids
- 27 Basic System Wiring Diagram - Circular and Sky Mexico
- 28 Basic System Wiring Diagram - Linear
- 29 Switchplate Mounting Template