advertisement
5 Functions and settings
5.7.2
While Figure 69 shows in full an event lasting less than 5 minutes, Figure 70
splits up events lasting more than 5 minutes. Here the first area in which the limit value is exceeded has been recorded in full with the 10 second lead time. Once the 5 minutes have been exceeded, the recording is however aborted automatically. Only when the value falls back below the set set threshold value is recording restarted with a lead time and follow-up time. An event lasting longer than 5 minutes is therefore split into 2 events displayed separately.
Average value data
The voltage regulator determines the voltage and complex current over an averaging period. This can be set by the user in the menu:
Configuration > Memory.
Based on the basic data, the following values may be displayed in the graphic depending on the time:
• Voltage U
• Tap position
• Active current IWirk
• Reactive current IBlind
• Active power P
• Reactive power Q
• Apparent power S
• Power factor cos Phi
© Maschinenfabrik Reinhausen 2010
2226825/00 EN TAPCON
®
-trol
89
5 Functions and settings
Proceed as follows to display this data:
Select the data required in the "Tap position" list function below.
Figure 71 "Tap position" list function
The 4 power and power factor data types are calculated from the voltage and complex current and from the basic voltage regulator configuration with regard to the mains type and converters used.
Given the high volumes of data involved, the results of the average value memory are simply presented in graphic form, but not as a table.
90
TAPCON
®
-trol 2226825/00 EN
© Maschinenfabrik Reinhausen 2010
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 13 Introduction
- 13 Manufacturer
- 13 Subject to change
- 13 Completeness
- 14 Supporting documentation
- 14 Storage site
- 14 Illustration conventions
- 15 Abbreviations used
- 16 Information concept
- 16 Typographic conventions
- 17 Installation
- 17 Typical installation
- 18 Custom installation
- 20 Selecting device
- 23 Product description
- 23 Scope of delivery
- 24 Basic tasks of visualization software
- 26 Description of basic structure
- 27 Description of toolbar
- 29 Basic settings
- 29 Selecting language
- 30 Menu item: Settings
- 30 Setting communication options
- 39 Other settings
- 43 Functions and settings
- 43 Menu item: Group
- 43 Inserting groups
- 46 Opening group
- 48 Deleting group
- 50 Saving group data
- 52 Menu item: Device
- 53 Creating new device
- 56 Opening device
- 60 Deleting device
- 61 Archiving device data
- 63 Connecting
- 66 Setting time on device
- 68 Changing device data
- 69 Changing parameter information
- 70 Menu item: Parameter set
- 70 Cutting
- 71 Copying
- 72 Pasting
- 72 Deleting
- 73 Downloading/updatingparameters
- 75 Uploading parameters
- 77 Parameter and data structure of visualization
- 78 Parameter groups
- 79 Parameters
- 80 Modules
- 81 Basic functions
- 84 250 Short-term memory
- 84 Display data archive
- 87 Peak/Demand
- 88 250 Measurement archive
- 88 Event data
- 89 Average value data
- 91 Reading event data
- 92 Reading average value memory
- 93 Event/measured value overview
- 95 Remote
- 96 Description of further menu structure
- 96 Menu: File
- 100 Menu: View
- 102 Menu: Tools
- 109 Troubleshooting