advertisement
Connecting the RJP (Remote Jack Pack)
Output to any external source connected to RJP on the hotel desk.
RJP Rear
USB HDMI VIDEO AUDIO AUDIO/PC
3
Video Cable
2
Audio Cable
5
TV Rear Panel
4
HDMI cable
1
D-sub / PC Audio cable
1. Connect the PC IN / PC/DVI AUDIO IN port of the TV to the PC/AUDIO port of the RJP.
2. Connect the AV IN [VIDEO]/[L-AUDIO-R] port of the TV to the VIDEO port of the RJP.
3. Connect the AV IN [VIDEO] port of the TV to the VIDEO port of the RJP.
4. Connect the HDMI IN 1 , 2(DVI) or 3 (ARC) port of the TV and the HDMI port of the RJP.
5. Connect the RJP port of the TV and the RS/232 port of the RJP.
✎
The RJP (Remote Jack Pack) compatible with this Samsung TV is TeleAdapt TA-7610, TA-7650 (HD) and TA-
7660 (HD Plus).
• RJP (Remote Jack Pack): RJP stands for Remote Jack Pack. The RJP is a hardware module that has different Audio
Video inputs (A/V, Audio, PC and HDMI) and corresponding outputs. The corresponding output sources are connected from RJP to TV. The RJP communicates with the TV via RS232. Hot Plug & Play is a function that allows hotel guests to connect an external source to the RJP. The RJP communicates with the TV by sending messages regarding
Active/Inactive sources. The TV will switch to the Active external source according to the priority set by the User.
✎
You can select HDMI IN 1 , 2(DVI) or 3(ARC) and AV IN for connecting RJP .
✎
When the TV is on, connect the TV and the RJP within 10 seconds.
18
English
• The RJP can be returned to the factory default settings by pressing the A/V and HDMI buttons simultaneously for 10 seconds. All LEDs blink 5 times to acknowledge that this has been finished.
• The RJP will automatically turn off any LEDs after 5 minutes to avoid unnecessary light pollution in the hotel room.
The LEDs that were turned off will turn on again if the guest touches any of the buttons and the 5 minute timer will restart. If the guest then touches another source button, the TV will change to the selected source and the corresponding LED will be lit.
• After an RJP Reset or a TV Power OFF/ON, it takes approx. 10 seconds to establish communications between the
TV and the RJP.
• The following table shows the approximate time in seconds to switch from the TV to the input source, based on the priority.
✎
Scenario 1: When no inputs are connected.
Source
AV
PC
HDMI
To Connect
2 Sec
0.7 Sec
3.9 Sec
✎
Scenario 2: When two or more inputs are connected and an Input source is disconnected and then reconnected.
Source
AV
PC
HDMI
Disconnect
4.5 Sec
0.7 Sec
3.9 Sec
To Connect
2 Sec
0.7 Sec
3.9 Sec
Total
6.5 Sec
1.4 Sec
7.8 Sec
✎
E.g. If the RJP has all its live sources AV, PC and HDMI connected, AV is viewed as the highest priority. If the RJP is in HDMI mode, and a guest removes and reconnects the AV, the minimum time required to switch to the AV is
6.5 seconds.
• To connect audio (Ipod or Mp3), Music mode should be ON and Jack Ident detect should be OFF.
• A/V, PC and HDMI input sources are supported.
English
19
advertisement
Related manuals
advertisement
Table of contents
- 2 Instruction
- 2 Operational Modes
- 2 Still image warning
- 2 Securing the Installation Space
- 4 Accessories
- 5 Installing the LED TV Stand
- 6 Assembling the swivel (32 inch TVs or larger)
- 8 Viewing the Connection Panel
- 11 TV Controller
- 13 Connecting the TV with SBB
- 15 Connecting the Bathroom Speakers
- 17 Connecting the MediaHub HD
- 18 Connecting the RJP (Remote Jack Pack)
- 20 Setting the Hotel Option Data
- 58 Installing the Wall Mount
- 59 Securing the TV to the Wall
- 59 Anti-theft Kensington Lock
- 60 Specifications
- 61 Dimensions