Using the REMOTE ID function. Christie LW651i-D White, LX801i-D Black, LW751i-D Black, LX801i-D White, Christie LWU701i-D Black, LW651i-D Black, Christie LWU701i-D White, LWU601i-D Black, LW751i-D White, LWU701i-D Black
Add to My manuals131 Pages
advertisement
Remote control
Using the REMOTE ID function
Use this function to control specific projectors by the remote control assigned the same ID number when you use multiple projectors of the same type at the same time.
Assign an ID number to each projector before using the
REMOTE ID item in the SERVICE menu of the OPTION menu (95). Press the ID button with the same ID number as assigned to the projector you are going to control. The ID button selected lights for several seconds.
ID
buttons
NOTE
• Each time you press any button (except ID buttons), the ID button of current selected ID number lights.
• To confirm the projector's current ID, press any ID button for three seconds.
Its number is shown on each screen regardless of set ID of projector.
Changing the frequency of remote control signal
The accessory remote control has the two choices on signal frequency Mode
1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency.
To set the Mode, press the combination of two buttons listed below simultaneously for about three seconds.
(1) Set to Mode 1:NORMAL
MENU
and MY BUTTON-4 buttons
(2) Set to Mode 2:HIGH
AV MUTE
and MY BUTTON-1 buttons
AV MUTE
(2) button
MY
(1)
MENU
button
The REMOTE FREQ. in the SERVICE item of the OPTION menu (95) of the projector to be controlled should be set to the same mode as the remote control.
BUTTON-1
button
MY
BUTTON-4
button
LWU701i/LW751i/LX801i/LWU601i/LW651i
User's Manual - Operating Guide
29
020-000786-0
2
LIT MAN USR D2
advertisement
Related manuals
advertisement
Table of contents
- 4 Introduction
- 4 Features
- 4 Checking the contents of package
- 5 Part names
- 9 Setting up
- 11 Arrangement
- 14 Connecting with your devices
- 24 Fastening the cables
- 25 Fastening the adapter cover
- 26 Attaching the terminal cover
- 27 Using the security bar and slot
- 28 Connecting power supply
- 29 Remote control
- 29 Installing the batteries
- 30 Using the REMOTE ID function
- 30 Changing the frequency of remote control signal
- 31 About the remote control signal
- 32 Status Monitor
- 32 Displaying the condition of the projector
- 34 Displaying the log
- 36 Power on/off
- 36 Turning on the power
- 36 Turning off the power
- 38 Operating
- 38 Adjusting the volume
- 38 Temporarily turning off the screen and audio
- 39 Selecting an input signal
- 40 Selecting an aspect ratio
- 41 Adjusting the projector's elevator
- 41 Installation angle
- 42 Adjusting the lens
- 44 Using the automatic adjustment feature
- 45 Correcting the distortion
- 48 Using the EDGE BLENDING features
- 52 Using the magnify feature
- 53 Temporarily freezing the screen
- 53 Temporarily shading the screen
- 54 PIP (Picture in Picture)
- 58 Using the menu function
- 61 EASY MENU
- 63 IMAGE SETTINGS menu
- 67 SIZE AND POSITION menu
- 70 INPUT menu
- 75 SETUP menu
- 81 AUDIO menu
- 82 MENU PREFERENCES
- 88 OPTION menu
- 101 NETWORK menu
- 102 SECURITY menu
- 109 Maintenance
- 109 Replacing the lamp
- 114 Other care
- 115 Troubleshooting
- 115 Warnings displayed on the Status Monitor
- 115 Related messages
- 118 Regarding the indicator lamps
- 122 Resetting all settings
- 123 be mistaken for machine defects
- 130 Specifications