advertisement
R
VICTOR COMPANY OF JAPAN, LIMITED
is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD.
is a registered trademark in Japan, the U.S.A., the U.K. and many other countries.
© 2000 VICTOR COMPANY OF JAPAN, LIMITED
R
Printed in Japan
SL96186
VIDEO CASSETTE RECORDER
SR-S990E
SR-S990EK
INSTRUCTIONS
REC STOP REC
CHECK
VHS
PAL
625
OPERATE
VIDEO CASSETTE RECORDER
SR-S990E
REC
EJECT OPERATE
The illustration shows the SR-S990E.
625
VHS
PAL
Thank you for purchasing this JVC product.
Before operating this unit, please read the instructions carefully to ensure the best possible performance.
This instruction book is made from
100% recycled paper.
SL96186
2
SAFETY PRECAUTIONS
Warning Notice
FOR YOUR SAFETY (Australia)
1. Insert this plug only into effectively earthed threepin power outlet.
2. If any doubt exists regarding the earthing, consult a qualified electrician.
3. Extension cord, if used, must be three-core correctly wired.
IMPORTANT
Connection to the mains supply in the United Kingdom.
DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain a proper safety approved extension lead/adapter or consult your dealer.
BE SURE to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover.
If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow the instructions given below:
DO NOT make any connection to the Larger Terminal coded E or Green.
The wires in the mains lead are coloured in accordance with the following code:
Blue to N (Neutral) or Black
Brown to L (Live) or Red
If these colours do not correspond with the terminal identifications of your plug, connect as follows:
Blue wire to terminal coded N (Neutral) or coloured
Black.
Brown wire to terminal coded L (Live) or coloured Red.
If in doubt — consult a competent electrician.
CAUTION
䡲 When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet.
䡲 Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
To prevent electric shock, do not open the cabinet. No user serviceable parts inside. Refer servicing to qualified service personnel.
Note:
The rating plate and the safety caution are on the rear of the unit.
The OPERATE button does not completely shut off mains power from the unit, but switches operating current on and off.
Notes on the built-in lithium battery
WARNING:
THE UNIT CONTAINS A BUILT-IN LITHIUM
BATTERY FOR MEMORY BACK-UP THAT
MUST ONLY BE REPLACED BY SUITABLY
QUALIFIED SERVICE PERSONNEL.
FOR BATTERY REPLACEMENT, TAKE THE
UNIT TO YOUR DEALER OR A JVC SERVICE
STATION.
(Danish)
ADVARSELI
Lithiumbatteri — Eksplosionsfare.
Udskiftning ma kun foretages al en sagkynding.
og som beskrevet i servicemanualen.
This unit is produced to comply with Directives 76/889/
EEC, 82/499/EEC, 87/308/EEC and Standard IEC
Publ. 65.
CAUTION
POWER SYSTEM
Connection to the mains supply
This unit operates on voltages of 220V to 240 V AC,
50 Hz or 60 Hz.
䡲 To prevent electric shock and to avoid damaging the unit, first insert the smaller plug on the AC power cord into the VCR, making sure that it is securely connected, and then plug the larger end of the AC power cord into an AC outlet.
COPYRIGHT © 2000 VICTOR COMPANY OF JAPAN, LIMITED
Printed in Japan
OPERATION LOCK
By engaging the operation lock system [LOCK], you can prevent accidental or deliberate interference with recording operation or power supply.
When this function is activated, all operation buttons are disabled. However, you can still control the recorder with the remote control.
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP REC
CHECK
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET MENU
ON SCREEN
SHIFT
TIME MODE
– S E T +
EJECT OPERATE
“LOCK” indicator
[LOCK] button [TIME MODE+/–] button
1
Engage the mode you want to lock (such as the Rec or Play mode).
2
While pressing the [LOCK] button, press the [TIME MODE +/–] button. “LOCK” is shown on the display, indicating that the Operation Lock mode is engaged.
3
To unlock the VCR, press the [TIME MODE +/–] button while pressing the [LOCK] button. The “LOCK” indication on the display disappears and the unit can now be operated normally.
To prevent unauthorized use, detach this page and keep it in a safe place.
3
4
CONTENTS
1 INTRODUCTION
1-1 Major Features ............................................. 6
1-2 Periodical Maintenance................................ 7
1-3 Daily Inspection............................................ 7
1-4 Precautions .................................................. 7
1-5 Regarding S-VHS ET Recording ................. 8
2 CONTROLS AND CONNECTORS
2-1 Front Panel .................................................. 9
2-2 Display ....................................................... 11
2-3 Rear Panel ................................................. 12
3 CONNECTIONS
3-1 Connecting to a Camera ............................ 14
3-2 System Using Sequential Switcher ............ 15
3-3 Connecting the Rear Panel Input/Output
Terminal Connections ................................ 16
4 ON-SCREEN/MENU SWITCHES
4-1 On-Screen Display ..................................... 17
4-2 Main Menu Display .................................... 18
4-3 Date and Time Setting ............................... 19
4-4 Hour Meter Display .................................... 20
4-5 Alarm Input/Power Loss Data Display ....... 21
4-6 Menu Switch Setting .................................. 22
4-7 Contents of Menu Switches ....................... 23
5 PREPARATION
5-1 Cassette Loading/Unloading ...................... 27
5-2 Recording/Playback Speed Mode
Selection .................................................... 28
6 RECORDING
6-1 Switch Setting During Recording ............... 29
6-2 Recording Basic Operation ........................ 30
6-3 Timer Recording ........................................ 31
• Timer Recording Program Setting .......... 31
• Holiday Timer Recording Setting ............ 35
• Canceling/Changing Timer Recording
Program .................................................. 36
• Notes on Timer Recording ...................... 37
6-4 Alarm Recording ........................................ 38
6-5 Sensor Recording ...................................... 40
6-6 Series Recording ....................................... 41
6-7 Repeat Recording ...................................... 43
6-8 Recording with External VCR Activation
Signal ......................................................... 44
6-9 How to Restore Recording After Power
Failure ........................................................ 45
6-10 External Timer Recording .......................... 45
6-11 Tape End Buzzer ....................................... 45
7 PLAYBACK AND SPECIAL-EFFECTS
PLAYBACK
7-1 Preparation ................................................ 46
7-2 Playback .................................................... 46
7-3 Special-Effects Playback ........................... 47
• Still/Field advance/reverse playback ...... 47
• Shuttle search playback .......................... 48
7-4 Alarm Search/Date and Time Search ........ 49
7-5 Repeat Playback ........................................ 51
7-6 Counter Memory Function ......................... 51
7-7 Tracking/V. Lock Adjustment ..................... 52
7-8 V. Pulse ..................................................... 52
8 TROUBLESHOOTING
8-1 Error Indication .......................................... 53
8-2 No Error Indication ..................................... 54
9 OPTIONAL SA-K97U RS-232C INTERFACE
BOARD
9-1 Installation of the SA-K97U ........................ 55
9-2 SA-K97U Specifications ............................. 56
9-3 SA-K97U RS-232C Protocol &
Commands ................................................. 57
10 APPENDIXES
10-1 Tape Reel Counter/Tape Remaining Time
Table .......................................................... 64
10-2 Rear Panel’s Input/Output ......................... 65
10-3 Specifications ............................................. 66
The SR-S990E/EK is a video cassette recorder able to execute timelapse recording with VHS cassettes.
Use only videocassettes bearing the
625
or
PAL
mark.
This unit is designed for professional use.
JVC is not liable for compensation for loss or damage to recordings in the event this unit fails to record or play back properly because the unit malfunctions or a defective video cassette tape is used.
Please note that it may be unlawful to use any material recorded from TV broadcast programs or pre-recorded programs without the consent of the owner of copyright, except in cases where this material is recorded exclusively for personal use.
5
6
1 INTRODUCTION
1-1 Major Features
5
S-VHS/S-VHS ET recording
S-VHS or S-VHS ET is employed as the recording mode. Employing the S-VHS ET recording mode enables recording with a horizontal resolution of 400 lines on a VHS cassette. The VHS mode is only available for playback.
5
Extended timelapse recording for up to 240 hours
Recording times are selectable from 3 hours (SP mode) and L12/L24/24/48/72/120/168/240 (Timelapse mode)
(when E-180 tape is used).
In the L12 and L24 Timelapse modes, sound is recorded as well.
• Recording and playback are not possible in the Long
Play (LP) mode.
• L12/L24 modes cannot be selected for S-VHS ET recording.
When a tape recorded on this unit is played back on another VCR, noise may appear on playback picture.
5
Alarm recording function
When an alarm signal is input in the Record mode, the
3-hour mode is automatically engaged. Alarm recording time can be selected from 5, 10, 15, 30, 60, 120, or 180 sec., to tape end, or set manually.
An index code is automatically recorded at the start point of the alarm recording for use as an alarm cue signal. Alarm recording points can be accessed quickly with the alarm search function.
5
Sensor recording
Whenever an alarm signal is input in the Stop mode
(Stop, Timer Recording Standby or Operating Off mode), the Record mode is automatically engaged.
5
Time/date generator
Superimposes date, month, year, hour, minute and second on the image during recording. Also allows you to display the number of alarms, alarm time, and the number of the power failures on a monitor.
5
Timer-recording function
Up to 8 programs can be set for daily, weekly, or weekday timer-recording. You can also set timer recording for up to 16 days a year by specifying the date
(holidays, for example).
5
Tape position search function
You can automatically search the start of an alarm recording or search for a recording made at a specified date and time.
5
Recording check function
Recording conditions (quality) can be checked at any time during recording by pressing the recording check button.
5
Operation lock system
The secret operation lock system prevents an accidental or deliberate interference with VCR operation.
5
Camera switching signal output terminal
5
Warning function
Error indications are shown on the front panel display.
Error warnings include condensation and problems with cassette loading, cassette unloading, or the rotating system operation mode.
5
Operating mode-off video throughout function
Even when the operating mode is off, the camera’s EE input can be output from the VCR.
5
Series recording function
Two or more SR-S990E/EK can be connected for extended, long-term series recording. As the tape in each VCR reaches the end, the next unit in the series will automatically start recording.
5
Automatic re-start of recording after a power failure
5
Time adjust function
With the IN/OUT terminal for time adjustment, the time difference can be set to “0” with multiple SR-S990E/EKs connected. (adjustment time: 00:00/12:00)
5
Digital hour meter display
5
Repeat playback/recording
5
Alarm recording, tape end and warning electronic buzzer
5
Recording control with external activation signal
5
Counter end function
5
External timer connection
5
Summer time compensation function
5
Wired remote control (optional)
Used when an optional SA-K97U RS-232C interface board is installed.
5
RS-232C control
The SR-S990E/EK can be controlled via a personal computer. Operation status can be monitored on the computer.
→
For servicing
See the service manual page 2-2 “2.2 MAINTENANCE AND CHECK”.
1 INTRODUCTION
1-2 Periodical Maintenance
This VCR incorporates precision mechanical parts which will collect dirt over time and ultimately deteriorate and wear out.
Over long periods of use, dirt and dust accumulates on the heads, drums and tape transport mechanisms. Dust which penetrates the VCR (especially during outdoor use) also promotes the wear and deterioration of mechanical parts by causing poor contact between tape and heads. This also prevents the VCR from maintaining video and audio quality at high levels.
To prevent wear and deterioration, clean the heads regularly using a head cleaning tape. However, because a head cleaning tape alone cannot clean the entire tape transport mechanism, this should also be inspected periodically to prevent any problems that could result from a sudden failure.
As replacement and adjustment of parts require advanced skills and specialized equipment, please contact the person in charge of professional video equipment at your nearest JVC-authorized service agent for servicing.
Monitoring Usage Time
The total operation time reached by an ordinary home VCR in 5 or 6 years may be reached by a professional VCR in as few as 5 or 6 months. Therefore, it is important that the total hours of operation be carefully monitored. An hour meter in the on-screen display (see page 20) shows the accumulated time. In the chart below, the hours accumulated in each month are shown in relation to the number of hours used per day. Times shown in the shaded area indicate that maintenance should be performed.
Usage
time per day
1 month 2 months 3 months 6 months 12 months
2 hours 60 120 180 360 720
8 hours
12 hours
24 hours
240
360
720
480
720
1440
720
1080
2160
1440
2160
4320
2880
4320
8640
Periodic Maintenance
Check or replace the following mechanical parts according to the running time.
Running time
Drum ass’y (including heads)
Pinch rollers
1000H 2000H 3000H 4000H
^
^
䡬
䡬
䡬
䡬
䢇
䢇
Drive parts
^ ^ ^ 䡬
^ : Cleaning
䡬 : Check or replace as required.
䢇 : Replace
• Maintenance requirements may vary depending on the operating environment and usage. The information above should be used as a reference guide.
Replace the built-in lithium battery approximately every two years.
1-3 Daily Inspection
Although this unit has been designed for reliable operation over a long period of time, a daily inspection is recommended to ensure optimum performance. In particular, be sure to check the repeat recording/playback function on a daily basis.
Inspection procedure
1
Turn on the power for all units connected to the surveillance system.
2
Check the quality of the image shown on the monitor.
3
Check that the date and time shown on the monitor are correct.
4
Rewind the tape recorded the previous day for several seconds.
5
Press the play button for playback.
6
Check that the playback picture is normal.
7
Check that the recorded date and time are correct.
5 This unit includes a Recording Check function (using the
[REC CHECK] button). Use these features to quickly check recording quality on a daily basis.
If any problems are found after inspection, turn the power off, unplug the power plug from the AC outlet, and contact your JVC dealer.
1-4 Precautions
Handling and storage place
5
Avoid using the unit in places subject to the following conditions:
• extreme heat or cold
• strong magnetic fields (do not use a transceiver within
2 meters of this unit)
• high humidity
• dust and soil
• vibrations
• variations in temperature
5
Use this unit in horizontal (flat position) only.
5
To avoid overheating the unit, do not block ventilation slots or stack the units. If the internal temperature rises too high, the tape may be damaged.
5
Do not leave the unit in the Still or Record Pause mode for a long time as this may damage the tape.
After about 3 minutes, this unit automatically enters the
Stop mode.
5
Handle the unit carefully
• Do not place anything heavy on the unit (a monitor, etc.). A malfunction may occur.
• Do not put any foreign substance into the cassette loading slot.
• Avoid violent shocks to the recording chassis during transportation. Remove the cassette tape from the unit for transportation.
5
Turn off the power to save electricity when not using the unit.
7
1 INTRODUCTION
1-4 Precautions
Condensation
5
Condensation
When cold beer is poured into a glass, water drops appear on the glass’s surface. This phenomenon is called “condensation”. When condensation occurs on the VCR’s head drum and tape guides it may damage the tape.
5
Condensation occurs in the following cases.
• When the VCR is moved from a
Head drum
cold place to a warm place.
• In a room that has just been heated or in an area directly exposed to a cooler.
• When there is excessive humidity.
Video tape
5
When condensation is expected to occur
Turn the power of the VCR on before use.
5
If condensation has occurred
The VCR automatically ejects the cassette and the error indication “E-08” blinks on the display. Operation is disabled until the “E-08” indication on the display goes out.
VIDEO CASSETTE RECORDER
SR-S990E
REC
VHS
625
PAL
REC STOP
OPERATE
REW
REVERSE
PAUSE PLAY
FF
FIELD REV FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T +
EJECT OPERATE
Video cassette
Erasure prevention tab
Timelapse recording is performed over very long periods of time which means that a durable tape is required.
• Use an E-180 tape.
• Do not use an extended tape (such as E-240).
• Use only videocassettes bearing the mark.
625
or
PAL
• To prevent accidental erasure of a recorded tape, break the erasure prevention tab on the cassette. To use a cassette with a broken tab, place a piece of cellophane tape over the broken tab.
• Video cassettes cannot be used upside down.
• Leaving the tape in a partially wound condition for a long time may damage the tape. Rewind the tape to the beginning before storage.
1-5 Regarding S-VHS ET Recording
• The S-VHS ET recording feature of this unit ensures a picture quality (horizontal resolution of 400 lines) on a par with S-VHS when a VHS tape is used. This function is automatically activated when a VHS tape is inserted into the unit and recording started. This unit does not perform normal VHS recording.
• S-VHS ET recording is not performed in the linear
slow (L12/L24) mode.
• Playback of a tape recorded in the S-VHS ET format should be performed on this unit, or on a video deck equipped with function for S-VHS or S-VHS simple playback (SQPB). (Playback may not be possible on some video decks.)
• JVC HG (high-grade) VHS tapes are recommended for S-
VHS ET recording. Depending on the characteristics of the tape, correct recording may not always be possible.
Use the tape after making a test recording to ensure that recording is conducted correctly.
• Accidentally inserting a tape recorded in the S-VHS ET format into a dedicated VHS deck that is not designed for playback of this type could result in damage. To avoid this kind of accident, mark cassettes labels in such a way that you can easily distinguish between S-VHS ET and VHS recordings when storing cassettes.
• As far as possible avoid operations that apply a load to the tape, such as search playback, etc. This will result in deteriorating picture quality.
• Noise may appear in the playback picture during search playback and field advance. This is not a malfunction.
8
2 CONTROLS AND CONNECTORS
2-1 Front Panel
7 6 5
4
3
625
VHS
PAL
REC STOP REC
CHECK OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– +
V. LOCK
– +
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL
MENU
ON SCREEN
SHIFT
TIME MODE
–
S E T
+
VIDEO CASSETTE RECORDER
SR-S990E
REC
EJECT OPERATE
8 9 10
11 12 13
14 15
1
[OPERATE] button
Press to turn the operating mode ON/OFF. When this button is ON, the OPERATE indicator t
lights and the unit can be operated. When a cassette is loaded, operating mode is switched on and the OPERATE indicator lights automatically.
The OPERATE button does not completely shut off the mains power to the unit, but switches the operating current on and off.
2
[EJECT] button
Press to eject the cassette.
* The cassette cannot be ejected during recording.
3
[REC] indicator
This indicator lights during recording if menu switch
<RECORD LED> on the <F. DISP> screen is set to “ON”.
4
Cassette loading slot
Insert a cassette in this slot. Use a VHS cassette tape.
5
[REC CHECK] button
Use this button to check recording.
When pressed in the Record mode, the VCR will rewind the tape for about 5 seconds of tape time and then play back the rewound section in the 3H mode to check recording quality. Recording is resumed automatically after playback at the point where recording was interrupted.
• If picture quality is judged to be inferior during recording check, the heads are cleaned automatically and the error code “E-09” is shown on the display for about 10 seconds.
Recording will continue regardless of the results of the recording check.
6
[STOP] button
Press this button to stop the tape.
7
[REC] button
Press this button in the Stop mode to engage the Record mode.
8
[REW] button
• Press this button to rewind the cassette.
• Starts reverse playback when pressed in the Play mode.
• Starts reverse alarm search or date/time search when the
Search mode is specified with the
^
[SEARCH] button.
• Also controls field-by-field playback in the reverse direction.
2 1
9
[REVERSE] button
Starts reverse playback when pressed in any mode except
Record, Record-Pause and Record Check.
0
[PAUSE] button
• Engages the Record-Pause mode when pressed in the
Record mode.
• Displays a still picture when pressed in the Play mode.
• Field advance or reverse playback is executed each time the [FF] or [REW] button is pressed while pressing this button in the Still mode. (When the [FF] or [REW] button is pressed for more than 2 seconds, Continuous Field
Advance Playback mode is engaged. After about 3 minutes, the Stop mode is engaged.)
!
[PLAY] button
• Press to play back the tape.
• Press to engage the Record mode in the Rec-Pause mode.
@
[FF] button
• Press to fast-forward the tape.
• Starts fast-forward playback when pressed in the Play mode.
• Starts forward alarm search or date/time search when the
Search mode is specified with the
^
[SEARCH] button.
• Also controls field-by-field playback in the forward direction.
#
[TRACKING +/–] buttons
If picture noise appears during play or field advance, press these buttons to adjust tracking so that noise is reduced.
When the [+] and [–] buttons are pressed simultaneously, tracking is reset to the preset level.
• Tracking adjustment is not possible in the L12H and L24H
Linear Slow Timelapse Play modes.
$
[V. LOCK +/–] buttons
Press to reduce vertical picture jitter in the Still, Field
Advance Playback and Linear Slow Timelapse Play modes.
%
[TIMER] button
Normally use this button for timer recording. For details, refer to “Timer Recording” on page 31.
9
2 CONTROLS AND CONNECTORS
2-1 Front Panel
24 25
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC
STOP
REC
CHECK
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– +
V. LOCK
– +
TIMER SEARCH
DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T +
EJECT OPERATE
16 17 18 19
^
[SEARCH] button
Use to search the alarm recorded section or a section recorded at a specified date and time. In the Stop mode, select the search mode by pressing this button.
• Press once to engage the Alarm Search mode.
• Press twice to engage the Alarm Scan mode.
• Press three times to engage the Date/Time Search mode.
• Press four times to release the search mode.
After the search mode is selected with this button, press the [FF] or [REW] button to execute the search operation in the selected mode.
For details, refer to page 49.
&
[DISPLAY] button
Selects which data — current time, control tape counter
(00H 00M 00S — 23H 59M 59S) or reel tape counter (0 —
9999) — is displayed. Each time this button is pressed, the display switches to the next item.
*
[LOCK] button
Press to activate the operation lock function.
(
[CNT RESET] button
When the display shows the control tape counter or reel tape counter, press this button to reset to “00H00M00S” or
“0000”.
)
[RESET/CANCEL] button
• In the Timer Program Setting mode, press this button to cancel the program settings. For details, refer to “Timer
Recording” on page 36.
• Also press this button to interrupt alarm recording or to reset the alarm input data or power loss (power failure) data. For details, refer to pages 21 and 39.
• Resets the seconds in the currently displayed time to 00 when pressed together with the
( [CNT RESET] button
(except in menu setting mode).
- When the seconds value is 29 or less, the minutes value is the same but the seconds value is reset to 0.
(e.g. 12:34:29 [ 12:34:00)
- When the seconds value is 30 or more, the seconds value is reset to “00” and the minutes value is increased by one.
(e.g. 12:34:30 [12:35:00) q
[MENU] button
Press to display the date/time, timer program, and various other menu setting screens, as well as the hour meter, on the monitor. Press again to cancel the menu or hour meter display.
20 21 22 23
w
[TIME MODE/SET +/–] buttons
• Use to select the recording and playback speed mode.
Each time these buttons are pressed, the recording/ playback speed mode changes as follows. The recording/ playback speed mode is shown on the display.
3H: Standard
L12H: 12-hour linear slow
L24H: 24-hour linear slow
24H: 24-hour timelapse
48H: 48-hour timelapse
72H: 72-hour timelapse
120H: 120-hour timelapse
168H: 168-hour timelapse
240H: 240-hour timelapse
• The speed mode selection indication shown when no cassette is loaded is the indication shown when S-VHS tapes are used. When a VHS cassette is loaded after setting a speed that can only be selected when S-VHS tapes are used, the setting is automatically switched to a speed that can be selected when a VHS tape is used.
Example: After selecting L24H while no cassette is loaded, the setting becomes 24H when a
VHS tape is loaded.
• Also use these buttons during date/time setting, timer program setting and menu switch setting to specify setting values.
e
[ON SCREEN/SHIFT 7/t] buttons
• Use these buttons on the normal screen to move the display position or recording position of on-screen information. The position can be moved down by pressing the 7 button and to the right by pressing the t button.
• Use these buttons on the menu screen to select the desired item in date/time setting, timer program setting and menu switch setting.
r
Display section
For details, refer to page 11.
t
[OPERATE] indicator
Lights when the [OPERATE] button is turned on.
10
2 CONTROLS AND CONNECTORS
2-2 Display
1 6
7
8 9 10 11 12
13
2 3
1
Operation mode display
Shows the operation modes.
Playback Recording
Rewind
Fastforward
Timelapse playback
Still
Recordpause
Rewind search
Fast-forward search
Reverse playback
* ( ) mark in the Rec/Pause mode is shown in red.
2
Cassette indication
Lights when a cassette is loaded. Blinks when a cassette is being ejected.
3
[SP] indication
Shows the standard (SP) mode during recording/playback.
During timelapse recording/playback, the [SP] indication is shown.
4
Tape counter/clock indication
• Shows the current time (hour: minute: second), tape control counter (00H 00M 00S — 23H 59M 59S) or tape reel counter (0 — 9999) when the operating mode is on.
The display can be selected with the [DISPLAY] button.
Shows the current time when the operating mode is off.
When a cassette is ejected, the tape control counter and tape reel counter are reset automatically.
• When the cassette is rewound to the beginning in the
Repeat Recording or Auto Rewind mode using the counter end output function, the tape control counter and tape reel counter are reset.
• The control and reel counter counts slowly in the Timelapse mode.
• In the timelapse mode, the control counter shows the time equivalent to that shown when a tape is played back in the
3H mode.
(Example: The control counter advances 1 second for about 1 minute and 20 seconds in the 240H timelapse mode.)
• During date/time search setting and operation, “td” is shown in place of the seconds.
• Shows the setting item during menu switch setting.
4 5
5
Recording/playback speed display
• Normally shows the recording/playback speed mode set with the [TIME MODE] button.
• Shows the following indications in the Alarm Search mode.
During alarm search: Shows the specified alarm number
(example: AL12)
During alarm scan: Shows the alarm scan mode (ALSC).
During date/time search: Shows the specified date and time (example 2310).
• Shows setting details in menu switch setting.
• When an error occurs, the error indication “E-**” blinks (if the menu switch <WARNING> on the <F. DISP> screen is set to “ON”).
For error indications, refer to page 53.
* Tapes recorded in the LP mode cannot be played back.
In this case, the [LP] indication blinks in this section.
6
[TIMER] indication
Lights during timer recording programming/operation.
7
[REPEAT] indication
When <REPEAT REC> in the <VTR MODE> menu is set to
“ON”, this indication is shown. When <TAPE END MODE> in the <ALARM/SENSOR MODE> menu is set to “STOP” and the Repeat Record mode is engaged, the [REPEAT] indication goes out if alarm recording or sensor recording takes place.
8
[OVERLAP] indication
Blinks when programs scheduled for timer recording overlap.
9
Timer program number
All programmed timer recording numbers light.
During timer recording, the number of the program being recorded blinks. When the timer recording ends, this number goes out.
0
[AL] (alarm) indication
Shown during alarm recording or sensor recording.
Blinks when alarm recording or sensor recording ends.
!
[S-VHS] indication
Lights when a S-VHS cassette is loaded. In the playback mode, it lights during playback of a tape recorded in the S-
VHS mode.
@
[LOCK] indication
Lights when the operation lock function is activated.
#
[AL REC] (alarm recording) indication
Lights when the menu switch <REC MODE> on the <ALARM/
SENSOR MODE> screen is set to “ALARM” or “ALL”.
$
[SENSOR REC] (sensor recording) indication
Lights when the menu switch <REC MODE> on the <ALARM/
SENSOR MODE> screen is set to “SENSOR” or “ALL”.
11
2 CONTROLS AND CONNECTORS
4 6 8
1
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
VIDEO
Y/C
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
ALARM
COM
IN
ALARM
REC OUT
ALARM
RESET
TAPE
END OUT
COM CLOCK
RESET IN
WARNING
OUT
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
2
3 5
7 9 10
CAM SW
OUT
ALARM
IN
COM
ALARM
REC OUT
ALARM
RESET
TAPE
COM
END OUT
CLOCK
RESET IN
WARNING
OUT
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
1
[AC IN] connector
Connect to an AC 220-240 V, 50/60 Hz power outlet using the provided AC power cable.
2
[REMOTE] remote connector (RCA)
Connect the optional RM-G30U remote control.
3
[MIC IN] mic input connector
Connect a microphone with 3.6-mm dia. plug. When signals are input from both the microphone connector and the audio input connector, audio signals are mixed and recorded.
4
[AUDIO IN] audio input connector (RCA)
Receives audio signals from a connected audio source.
5
[AUDIO OUT] audio output connector (RCA)
Outputs audio signals. No signal is output in the
Timelapse Recording/Playback mode (except in the
L12H/L24H mode).
6
[VIDEO IN] video input connector (BNC)
Receives composite video signals from a connected camera or other video source.
* To input a composite video signal, set the menu switch
<VIDEO IN> to “LINE”.
7
[VIDEO OUT] video output connector (BNC)
Outputs composite video signals. Even when the power is not supplied to this unit, input signals (composite video signals) from a camera can be output through this connector (Operating mode-Off Video Throughout function).
8
[Y/C IN] YC input terminal (4-pin)
To input separate YC signals.
* When inputting separate YC signals, set the menu switch <VIDEO IN> to “Y/C”.
9
[Y/C OUT] YC output terminal (4-pin)
To output separate YC signals.
12
11 12 13 14 15 16 17 18 19 20 21 22
0
Signal ground terminal
This ground terminal is not provided for safety purposes.
It is used to ground signals. Connect this terminal to ground the signal between VCRs.
!
[CAM SW OUT] camera switching signal output terminal
When a sequential switcher is connected, this terminal outputs camera switching timing control signals. For details on these signals, refer to page 65.
@
[COM] common ground terminal
Connect to the signal ground terminal of a connected unit.
#
[ALARM IN] alarm signal input terminal
Receives signals to start alarm or sensor recording.
$
[ALARM RESET] alarm signal reset input terminal
Receives signals to cancel alarm recording.
* Alarm input data is not reset.
%
[ALARM REC OUT] alarm recording mode signal output terminal
Outputs +12 V signals during alarm recording.
^
[TAPE END OUT] tape end signal output terminal
Outputs a signal when the tape ends during recording.
If the menu switch <CNT TAPE END> on the <SRI/EXT
MODE> screen is set, signals are output when the specified tape reel counter value is exceeded.
• Outputs a +12 V signal during recording. When the tape ends or the specified counter value is passed, a 0
V (GND level) signal is output.
• When the tape ends during auto repeat recording or auto rewind recording, 0 V signal is output for about 2 seconds.
• Connect an external alarm or buzzer via an external interface.
• To cancel the output, press the [EJECT] button,
[PLAY] button, [FF] button or [REW] button.
2 CONTROLS AND CONNECTORS
2-3 Rear Panel
&
[COM] common ground terminal
Connect to the signal ground terminal of a connected unit.
*
[WARNING OUT] warning signal output terminal
Outputs warning signals (+12 V) when a tape running or mechanism problem occurs.
(
[CLOCK RESET IN] clock reset input terminal
Connect to a master clock or another SR-S990E/EK’s
[CLOCK RESET OUT] terminal. When the clock reset signal is input, the time is automatically synchronized with the master clock or another SR-S990E/EK’s clock.
However, the time difference between VCRs should be within ±30 seconds.
When the clock reset signal is input, the clock in this unit is reset as shown below.
• When the seconds value is 29 or less, the minutes value is the same but the seconds value is reset to 0.
(eg. 12:34:29 —> 12:34:00)
• When the seconds value is 30 or more, the second value is reset to 00 and the minutes value is increased by one. (e.g. 12:34:30 —> 12:35:00)
)
[CLOCK RESET OUT] clock reset output terminal
Outputs the clock reset signal.
The clock reset signal is output in the following cases.
• When the internal clock is at 0:00 or 12:00
When this unit is connected to another SR-S990E/EK’s
[CLOCK RESET IN] terminal, the other VCR’s clock can be set to the clock in this unit. However, the time difference should be within ±30 seconds.
q
[SERIES REC IN] series recording/VCR activation signal input terminal
Receives series recording signal or VCR activation signal from an external control device.
Select the input signal with the menu switches in the
<SRI/EXT MODE> menu.
5 Series recording input
A series recording signal is input when [SRI/EXT
REC] is set to “SERIES”.
• Connect to another VCR’s series recording signal output terminal.
• When the tape in the preceding VCR ends, a signal is delivered to this terminal and recording starts automatically.
When the menu switch <CNT TAPE END> on the
<SRI/EXT MODE> screen is set, the signals are delivered when the specified tape reel counter value is reached. Recording starts automatically.
5
VCR activation signal input
When [SRI/EXT REC] is set to “EXT”, recording is started and stopped with an external signal.
• Connect to an external control device.
If a VCR activation signal (ground input) is input to this terminal, the VCR starts recording automatically and continues recording for as long as the VCR activation signal is input.
w
[SERIES REC OUT] series recording signal output terminal
Outputs series recording signals.
A series recording signal is output when [SRI/EXT REC] is set to “SERIES”.
• Connect to another VCR’s series recording signal input terminal.
• Outputs a signal when the tape being recorded in this unit ends.
When the menu switch <CNT TAPE END> on the
<SRI/EXT MODE> screen is set, the signals are output when the specified tape reel counter value is reached.
13
3 CONNECTIONS
3-1 Connecting to a Camera
Microphone
Amplifier
Microphone M3.5 minijack
RCA
BNC
4-pin
Video camera
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
VIDEO
Y/C
RCA
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
ALARM
IN
COM
ALARM
REC OUT
ALARM
RESET
TAPE
COM
END OUT
CLOCK
RESET IN
WARNING
OUT
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
BNC
4-pin
COM ALARM IN
Provided power cable
AC 220-240 V
50/60 Hz
Alarm sensor
Monitor TV
1
Connect the monitor’s video/audio input connectors to the SR-S990E/EK’s video/audio output connectors.
2
Connect the video camera’s video output connector to the SR-S990E/EK’s video input connector.
3
Input audio signals to the audio input connectors via an amplifier.
4
When connecting an alarm sensor, connect it to the SR-S990E/EK’s alarm input terminal.
5
When the connection is complete, connect the power plug to an AC 220-240 V, 50/60 Hz outlet.
CONNECTION TO THE SW-501E/SW-502E SEQUENTIAL SWITCHER
SW-501E/SW-502E
JK102/JK202
D.GND
–
AT 1
AT 0
CS1 0
IN
OUT
IN
CS0 1
TMP1
SODT
SLV/MST
OUT
IN
IN/OUT
IN
TIMER INPUT connector
JK103/JK203
D.GND
AT 0
AT 1
CS0 1
CS1 0
TMP0
SODT
D. +5 V
–
OUT
IN
OUT
IN
OUT
IN/OUT
OUT
TIMER OUT connector
Sequential switcher
SW-501E/SW-502E
1.
Connect pin 6 on the sequential switcher's TIMER INPUT connector to the VCR's CAMERA SW OUT terminal. Connect pin 1 to the GND terminal.
2. Connect pin 8 on the sequential switcher's TIMER INPUT connector to pin 8 on its TIMER OUT connector.
Note:
● Be sure to use two DIN connectors for connections.
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
VIDEO
Y/C
CAMERA SW OUT
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
COM
ALARM
IN
ALARM
REC OUT
ALARM
RESET
TAPE
END OUT
COM CLOCK
RESET IN
WARNING
OUT
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
COM
14
3 CONNECTIONS
3-2 System Using Sequential Switcher
Video camera
1 2 3 4 5 6
Alarm sensor input
1 2 3 4 5 6
Alarm signal output
Video output Camera switching signal input
Sequential switcher
Alarm sensor
Microphone
RCA
BNC
Amplifier
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
VIDEO
Y/C
RCA
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
ALARM
IN
COM
ALARM
REC OUT
ALARM
RESET
TAPE
END OUT
COM CLOCK
RESET IN
WARNING
OUT
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
BNC
CAM SW
OUT
4-pin
ALARM IN
Provided power cable
AC 220-240 V
50/60 Hz
Monitor TV
1
Connect video cameras and alarm sensor to a sequential switcher (frame switcher).
2
Connect the sequential switcher’s (frame switcher) alarm signal output, camera switching signal input and video output to the SR-S990E/EK.
3
Connect the monitor’s video/audio input connectors to the SR-S990E/EK’s video/audio output connectors.
4
When the connection is complete, connect the power plug to an AC 220-240 V, 50/60 Hz outlet.
5
Synchro should be applied to all connected video cameras.
6
When connecting the camera switching signal input terminal of the sequential switcher (frame switcher) to the SR-S990E/
EK, set the menu switch <CAM SW>.
15
3 CONNECTIONS
3-3 Connecting the Rear Panel Input/Output Terminal Connections
[CAM SW OUT] camera switching signal output terminal
CAM SW
OUT COM
Sequential switcher camera switching signal input
[ALARM IN] alarm signal input terminal
ALARM
IN COM
Sequential switcher alarm output terminal
[ALARM RESET] alarm reset terminal
ALARM
RESET COM
Vcc
Vcc: 5V–12V
Switch
[TAPE END OUT] tape end output terminal
TAPE
END OUT COM
Alarm lamp
External interface
[ALARM REC OUT] alarm recording mode signal output terminal
ALARM
RESET
ALARM
REC OUT COM
Alarm lamp
Switch
External interface
[WARNING OUT] warning signal output terminal
WARNING
OUT COM
Alarm lamp
External interface
[CLOCK RESET] clock reset terminal
5
When setting the clock to the first VCR’s clock
First VCR
CLOCK
OUT COM
Second VCR
CLOCK
IN COM
Last VCR
CLOCK
IN COM
5 When setting the clock to the external master clock
External master clock
First VCR
CLOCK
IN COM
Second VCR
CLOCK
IN COM
Last VCR
CLOCK
IN COM
External interface example
Example: Lamp lights with HIGH signal
(Lamp, etc.)
Power supply
Relay
Control signal
GND
5
Use appropriately rated devices.
16
4 ON-SCREEN/MENU SWITCHES
4-1 On-Screen Display
Displays the time date (date and time), recording speed, number of alarms and number of power losses (power failures) on screen in the Stop mode, Record mode and Record-Pause mode.
During recording, the on-screen data is recorded together with video signals.
• The on-screen display position can be moved with the [ON SCREEN] buttons.
• The type of data shown and display brightness can be selected on the <ON SCREEN /F. DISP MODE> screen.
[ON SCREEN 7] button
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP REC
CHECK OPERATE
REW
REVERSE
PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T +
EJECT OPERATE
RESET/
CANCEL
MENU
ON SCREEN
SHIFT
TIME MODE
–
S E T
+
[ON SCREEN t] button
Time (hour, minute, second)
On-screen display
Recording speed (ALARM indication during alarm/ sensor recording)
Date (day, month, year, week)
Number of alarms
*
*
*
*
*
*
A
*
0
0
0
1
:
–
0
0
0
1
:
–
L – 0 5 6 *
Z O O M O N
0
2
1
0
*
0
*
0
B L
U M
P
.
L
*
*
*
*
*
M
D
A
A
D U R E
*
*
*
*
4
*
*
*
*
F
C
T
*
*
*
*
I
R
E
*
*
*
*
N
*
E
*
H
*
*
*
*
*
T
E
E
U
L
R
E
E
*
*
*
*
*
B
*
*
*
*
D E
A
*
*
*
*
*
N D
*
*
*
*
*
*
*
*
M E
*
*
*
*
E
*
*
*
2 4
S A
–
*
0
*
H
T
4
*
*
*
*
*
*
*
*
N U
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
T
*
*
*
4
*
*
*
*
*
A U
M
A
*
.
.
*
T O
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
5
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Number of power losses
(power failures)
[ON SCREEN 7]
button
[ON SCREEN t] button
0
0
0
1
:
–
0
0
0
1
:
–
0
2
1
0
*
0
*
0
*
*
*
*
*
*
*
*
A
*
L
Z
–
O
0
O
M A C
D
D
*
*
*
*
4
A T
U R
*
*
*
*
F
*
*
*
*
I
5
M
R
E
E
*
*
*
*
N
6
O
*
N
B
U
L
M
P
.
*
E
*
*
*
*
*
*
H
*
*
*
*
*
D
T
E
B
*
*
*
*
E
E
U
A
*
*
*
*
*
L
R
N
*
*
*
*
M
L
*
E
E
*
*
*
*
D E
*
*
*
*
E
–
*
*
*
N
*
*
2
S
0
*
4
A
H
T
4
*
*
*
*
*
*
*
*
U
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
A
M
U
.
*
*
A
*
.
*
*
*
*
*
*
T 4
*
*
*
*
*
5
*
*
*
*
*
*
*
*
*
*
*
T
*
O
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Display items
ON SCREEN MODE screen
3
4
5
6
*
1
2
*
*
2
*
1
.
.
.
*
.
*
T
*
O
M A N
.
.
D
T
A
I
[
N
O
E
U
T
M
.
E
E
N
E
S
*
*
N U
*
B
T
C
*
L A
M
E
R
*
.
L
R
A
E
L
C
A
*
R
P O W E
S
M
P
B
R M
E
C
E
N
L O
E
*
N
*
E
D
T
E
*
C
*
*
*
E
S S
M O
.
.
4
R
D
E
W
F
A
I
[
C
F
*
R
N
N
*
R O
T A
N T
L L
*
Y
D
*
I
D
N
E
G
*
* * *
M E N
N
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
I
U *
*
*
C
S
*
*
*
N T
P L
*
*
*
M
*
O
*
D
*
E
*
*
*
*
*
M .
A .
* *
*
*
*
*
T
*
4
*
*
5
I N
A
*
*
*
Y
*
*
*
E
]
*
*
*
*
*
]
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O
O
N
N
*
O
O
*
*
N
N
*
*
*
*
*
*
1
*
0
*
O
*
0
*
N
O
O
N
N
*
*
*
*
*
*
*
*
*
*
*
*
Preparation
5
Connect the video output connector of this unit to the monitor’s video input connector.
1
Turn on the monitor and VCR.
2
When a video signal from a camera is input to the video input connector, on-screen data is superimposed on the picture.
When there is no input signal, on-screen data is shown on a black background.
Selecting the data display
The data displayed on-screen can be selected on the <ON
SCREEN MODE> screen.
Set the <ONSCREEN/F. DISP MODE> setting to “ON”.
5
When you do not want to display or record on-screen data, set the corresponding menu item to “OFF”.
* When the display contents setting is changed, the onscreen indication will be in the upper left corner.
Changing the on-screen display position
5
Move horizontally.
Press the [ON SCREEN t] button.
[ The display position is moved to the right
5
Move downward.
Press the [ON SCREEN 7] button.
[ The display position is moved down.
Changing the on-screen display brightness
Set the brightness with the menu switch <TONE> on the
<ON SCREEN MODE> screen. Select 0, 30, 70 or 100.
• The higher the number, the brighter the characters.
* For details on menu operation, refer to page 22.
17
4 ON-SCREEN/MENU SWITCHES
4-2 Main Menu Display
You can display date and time data recorded when an alarm input or power failure occurs, as well as the hour meter (drum rotating time) by selecting the desired item in the main menu.
The date/time setting screen, menu switch setting screen for each application, and timer recording program setting screen can also be displayed by selecting the desired item in the main menu.
Date/time setting, menu switch setting and hour meter can be checked on the VCR’s display as well.
[SHIFT 7] button
[SHIFT t] button
VIDEO CASSETTE RECORDER
SR-S990E
REC
EJECT OPERATE
OPERATE
CNT RESET MENU
ON SCREEN
SHIFT
TIME MODE
– S E T +
[MENU] button
[SET +] button
[SET –] button
Main menu screen
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
4
*
*
*
*
*
*
*
*
*
*
*
C
V
*
L
*
O
*
C
O N
I
S
D
C
E
*
K
R
O
*
*
/
[
S
V
M
E
E E N
T
E
T
/
R
N
*
S
A
B
P
H
R
L
U
R
O
I
A
Z
O
L
/
R
Z
G
I
E
M
E
R
D
X
/
R
A
A
T
S
/
M
Y
*
E N
*
*
I
M
N
T
S
*
*
F
H O
O
I
T
N
U
H
R
E R
M E
*
*
M
T
*
E
E
*
N
R
*
U
F
*
.
D I
M O D
O
S
U
*
D
O
*
]
E
R
*
I
O
M
E T
*
*
*
U
E
*
*
*
*
T
R
*
*
*
*
*
*
*
*
*
*
S
E
*
M O D E
*
*
*
*
*
*
P
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
M
*
*
*
*
*
*
*
*
*
*
O
*
*
*
*
*
*
*
*
*
*
*
D
*
*
*
*
*
*
*
*
*
*
*
E
*
*
*
*
*
*
O N
O
*
N
*
*
*
*
*
O N
O N
*
Cursor
Operation
5
Connect the video output connector of this unit to the monitor’s video input connector.
1
Turn on the monitor and VCR.
2
Press the [MENU] button.
[ The main menu screen is shown on the monitor screen.
3
Press the [SHIFT 7] button to move the cursor to the item you want to display.
4
Press the [SET +/–] button to display the selected menu screen on the monitor (see below).
5
To restore the main menu screen, press the [MENU] button.
To cancel the main menu mode, press the [MENU] button again. The normal screen is restored.
Contents of the main menu items
5
CLOCK SET (VCR's display
cLSET)
Displays the date/time setting screen.
* Set the clock before operating the VCR (refer to page 19).
5
ONSCREEN/F. DISP MODE (VCR's display
DiSP)
Let’s you choose whether or not to display onscreen display items, brightness selection, [REC] indicator and warning indicator.
5
VIDEO/VTR MODE (VCR's display
ViDEO)
For VCR operation settings such as V. Pulse ON/
5
5
OFF, counter memory function and repeat recording/playback.
SRI/EXT MODE (VCR's display
SRi ET)
For setting series recording or automatic recording with an external signal.
ALARM/SENSOR MODE (VCR's display
ALSEN)
For setting alarm recording or sensor recording operation.
18
5
BUZZER/IN OUT (VCR's display
BU22iO)
Turn ON/OFF buzzers such as the tape end buzzer and alarm/sensor buzzer and set camera switch signal output.
5
PROGRAM TIMER (VCR's display
PRG)
Shows timer recording program settings with the day of the week.
5
HOLIDAY SET (VCR's display
HOLiDY)
Shows timer recording program settings at specified dates.
5
HOUR METER (VCR's display
HOUR)
5
Shows the VCR’s operating time (drum rotation time).
OTHER (VCR's display
OTHER)
Shows the date and time when an alarm was input or a power failure occurred.
4 ON-SCREEN/MENU SWITCHES
4-3 Date and Time Setting
The time/date generator and timer recording will not function if the time and date are not set.
Set the day/month/year, hour/minute and Summer Time Compensation ON/OFF on the CLOCK SET screen. The setting can be checked even on the display.
RESET/
CANCEL ON SCREEN
VIDEO CASSETTE RECORCER
SR-S990E
REC
625
VHS
PAL
REC STOP
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
–
+
V. LOCK
–
+
TIMER SEARCH DISPLAY LOCK CNT RESET
ON SCREEN
MENU
SHIFT
TIME MODE
– S E T +
EJECT OPERATE
MENU
SHIFT
TIME MODE
–
S E T
+
[SET +] button
[CNT/RESET] button
[MENU] button
[RESET/CANCEL] button
[SET –] button
Cursor indication
Main menu screen
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
4
*
*
*
F
*
C
O
I
* *
L O
T
N
H
* *
C K
E R
*
*
[
S
M E
E T
N
*
U
*
*
*
*
*
*
*
*
*
*
*
*
*
O
*
*
V
S
A
B
P
H
H
N
I
R
L
U
R
O
S
D
I
A
Z
O
O L
U
C
E
R
O
E
/
E
V
/
R
E
M
X
/
T
S
Z
G
I
R
E
R
D
R
A
A
/
M
Y
M E
N
T
I
*
*
T
/
R
*
E
M
N
N
T
S
E
F
*
I
R *
.
M
O D
M
E T
D
O
E
E
*
*
I
D
*
R
*
*
S
E
*
*
*
*
P
*
*
*
*
*
*
*
*
*
*
*
M
*
*
S
*
O
O
R
U
*
T
M
*
O
*
D
*
E
*
*
*
*
O
*
*
*
*
*
*
*
D
*
*
*
*
*
*
*
E
*
*
O
O
N
N
*
*
O
*
N
*
*
*
*
*
*
M *
E
*
N
*
U
*
*
]
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O
*
*
*
N
*
VCR's display
cL SET
[SET +] button
Cursor indication
CLOCK SET screen
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
S U M M E R
*
4
F I N
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
[ C
*
–
*
–
L O
*
–
*
*
C
*
T
*
I
K *
*
M
S E
*
E
*
*
*
–
T ]
*
–
*
*
–
*
–
*
*
*
*
*
*
*
–
*
0
*
*
T
*
–
*
*
*
*
*
*
*
0
*
D
*
0
*
A
*
:
*
I
*
1
*
–
*
M
*
0
*
E
*
*
1
*
*
*
*
E N U
*
0
*
*
–
*
T E
*
2
*
*
*
*
0
*
0
*
*
*
0
*
*
*
*
–
*
*
*
*
*
*
*
*
*
–
*
*
*
*
*
–
*
*
*
0
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O N
O N
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O F
O F
* *
F
F
*
*
*
[SHIFT 7/t] and
[SET +/–] buttons
*
*
*
*
*
*
*
*
4
* * * *
*
U
*
M
*
M
*
E
F I N
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
S
*
*
*
*
*
*
*
*
*
*
*
R
*
*
*
*
*
*
*
*
–
*
*
*
[
*
C L O C
*
–
*
*
*
*
–
*
*
*
*
*
*
*
*
*
T
*
1
*
*
*
*
–
*
–
*
0
T
*
I
*
–
*
1 –
*
*
D
*
A
0
*
1
T
*
–
*
M
*
E
E
*
*
*
*
N U
I
*
2
*
K
*
*
*
*
:
*
S
*
M E
*
3
*
E
*
0
*
*
*
2
*
*
*
E
*
*
*
–
*
0 0
*
*
*
*
*
*
–
*
*
*
T
*
–
*
*
*
]
*
0
*
–
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
–
*
–
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O
*
O
O
F
F
* *
*
*
N
*
*
F
F
*
*
*
*
*
*
O
*
N
*
*
*
*
0 1 0 1 2 0 0 0
Press twice the [MENU] button.
Normal screen
*
*
*
*
*
*
*
*
*
*
1
0
2
1
*
*
*
*
*
4
*
*
*
* *
F
*
*
*
*
*
*
*
*
:
–
3
0
*
*
*
*
*
*
*
*
*
I
*
N
*
*
*
*
*
*
*
*
*
*
0
1
*
*
*
*
*
*
*
:
–
0
2
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1
0
*
0
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
E N
*
U
*
*
*
*
*
*
*
*
*
*
*
*
2 4 H
S A T *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
0
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O N
O N
* *
*
O
*
F
*
F
** *
* *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Operation
1
Turn on the monitor and VCR.
2
Press the [MENU] button to display the main menu screen.
3
Press the [SHIFT 7] button to set the cursor on <CLOCK
SET> on the main menu.
4
Press the [SET +/–] button.
[ The <CLOCK SET> screen is shown. The cursor shows the <TIME> setting item and the hour digit blinks.
* Check that <SUMMER TIME> on the last line is set to
“OFF.
5
Set the “hour” by pressing the [SET +/–] button. This VCR uses the 24-hour system.
• Press the [SET +] button to increase the numerical value and the [SET –] button to decrease it (same for minute, day, month and year setting).
5
During summer time period, set the time with a one-hour delay.
5
During standard time period, set the actual time.
6
Press the [SHIFT t] button so that the minutes digit blinks.
7
Press the [SET +/–] button to set the minutes.
8
Press the [SHIFT 7] button.
[ The <DATE> setting item is shown by the cursor and the day item blinks.
5
Press the [SET +/–] button to set the day.
9
Press the [SHIFT t] button so that the month item blinks and set the month with the [SET +/–] button.
0
In the same way, press the [SHIFT t] button so that the year item blinks and set the year with the [SET +/–] button.
!
For summer time compensation
• Press the [SHIFT 7] button to set the cursor to <SUMMER
TIME> and press the [SET +/–] button to set <SUMMER
TIME> to “ON”.
[ The time is automatically adjusted one hour forward in the summer.
@
End date/time setting.
• Press the [MENU] button.
[ The monitor screen returns to the main menu screen and the time count starts from 00 second.
• Press the [MENU] button again to restore the normal screen.
19
4 ON-SCREEN/MENU SWITCHES
4-3 Date and Time Setting
Summer Time Compensation
• When setting the time, make sure the <SUMMER TIME> item is set to “OFF”.
When this unit is shipped, this item is set to “OFF”.
During daylight savings time
1
Set the time with a one-hour delay.
2
After setting the time, set the <SUMMER TIME> item to
“ON”.
• The set time advances one hour.
3
At the end of the daylight savings time season, set the
<SUMMER TIME> item to “OFF”.
• The standard time instead of <SUMMER TIME> is displayed.
Time setting for 29 seconds or less
When the seconds value is 29 or less, you can reset it to 00 by pressing the [CNT RESET] button while pressing the [RESET/
CANCEL] button.
• For 30 or more, the seconds value is reset to 00 and the minutes value is increased by one.
Standard time
1
Set the clock to the actual time.
2
When daylight savings start, set the <SUMMER TIME> item to “ON”.
• The time advances one hour on the display.
Notes:
• If the power plug has been disconnected from an AC outlet for a long time, make sure the set time is correct before using the unit. (Clock time may be affected by environmental factors.)
• When the built-in backup battery capacity is low, the error indication E-10 appears on the display. Contact your local
JVC dealer to replace the built-in battery.
4-4 Hour Meter Display
Drum rotation time is displayed on the monitor’s screen and the VCR's display in the form of an hour meter. Use this data to schedule maintenance.
Main menu screen
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
4
*
*
*
*
*
*
* *
C
O
L
N
* *
O
S
C
C
*
K
R
* [
*
E
S
E
M E
E
N
T
/
N
*
F
U
*
.
]
*
D
*
*
I
*
*
S
*
*
P
*
*
*
V
S R
A
I
L
D
I
A
E
/
R
O
E
M
/ V
X T
/ S
B
P
U
R
Z
O
Z
G
E
R
R
A
T
*
R
M
/
M *
I
E N
N
T
*
O
S
*
I
M
D
O
O
M
*
*
*
F
H O
H O
O
I
T
N
L
U
H
I
R
D
E R
A
M E
*
*
Y
M
*
T
*
E
S
E
*
N
E
R
*
U
T
*
*
*
O
E
R
U
E
*
*
*
*
D
*
*
T
R
*
*
*
*
E
*
*
*
*
*
*
*
M O D
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* * *
*
M
*
O
*
D
*
*
E *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O N
O
*
N
*
* *
O N
O N
* *
*
*
*
*
E
*
*
*
*
*
VCR's display
HOUR
Operation
1
Turn on the VCR and monitor.
2
Press the [MENU] button to display the main menu.
3
Press the [SHIFT 7] button to set the cursor on the
<HOUR METER> on the main menu.
4
Press the [SET +/–] button to show the hour meter (drum rotating time) on the monitor.
5
Press the [MENU] button twice to restore the normal screen.
[SET +/–] button
Hour meter screen
*
*
*
*
*
*
*
*
D
*
*
*
*
*
*
*
*
*
R U M
*
*
*
*
*
*
*
*
4
*
*
*
*
*
*
*
*
F
*
*
*
*
*
*
*
*
*
I
*
*
*
N
*
*
*
*
*
*
*
*
*
[
*
O N
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* *
*
*
*
*
*
*
*
*
*
*
*
*
*
H
*
O
*
U
*
R
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* *
E
*
*
*
*
* *
N U
*
*
*
*
*
*
*
*
*
*
M
*
E
*
T
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
E R
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
]
*
0
*
*
*
*
0
*
*
*
*
0
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
4
*
*
*
0
*
*
*
*
*
7
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O F
*
*
*
*
*
*
*
**
*
*
*
*
F
*
*
*
*
H
*
*
*
20
For servicing
See the service manual page 1-10 “1.4 LITHIUM BACKUP BATTERY”.
←
4 ON-SCREEN/MENU SWITCHES
4-5 Alarm Input/Power Loss Data Display
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
4
*
*
*
*
*
*
*
*
*
C
O N
V I
*
L
*
O
*
C
S
D
C
E
S R I
*
K
*
*
[
S
M
E
E
T
N
*
U
*
]
*
*
*
/
R E
O
E
/
X
E
V
T
N /
T R
* M
F
*
O
.
D
D E
I
M O D E
*
S
*
*
*
A
B
L
U
A
Z
R
Z
M
E
/
R
S
/
E
I
N
N
S
*
O
O
R
U
*
*
*
*
F
P R
H O
H
O
I
O
T
N
O G
L
U
H
I
R
E
R
D
A
A
R *
*
M
Y
M E
*
*
T
M *
E
T
S E
E
*
N
R
*
I
U
M
T
*
*
*
E
*
*
*
*
R
*
*
*
*
*
*
*
*
*
P
*
*
*
*
*
*
*
*
*
*
*
*
*
T
M
*
O
*
D
*
*
*
*
*
*
*
*
*
*
E
*
*
*
*
*
*
*
*
M O
*
*
*
*
*
*
*
*
*
*
*
D
*
*
*
*
*
* *
O
O
N
N
*
*
*
*
*
*
*
E
*
*
O
O
*
*
*
*
*
*
*
N
N
*
Cursor indication
[MENU] button
[SET +/–] button
Alarm in/power loss list screen
*
*
*
*
*
*
1
2
*
*
*
*
4
*
*
*
*
*
.
.
*
*
*
*
*
*
*
*
*
*
A L
P O
A R
W E
M
R
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
F
*
*
*
*
*
*
I N
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
[
*
O
I
*
N
T
*
*
H
*
L
E R
*
I
*
S
L O S S
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
E
*
N
*
*
*
*
*
*
* L
*
*
*
*
*
*
*
U
*
*
*
*
*
*
*
*
*
*
*
*
]
*
T
I
*
S
*
*
*
T
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O F F
*
*
**
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
[MENU] button
[SET +/–] button
Alarm in list screen
A
A
*
*
L
L
*
*
A
A
L
L
–
–
0
–
0
0
*
*
–
–
*
*
A
A
L
L
–
–
–
–
A L
A
*
*
L
*
4
– –
–
*
F
–
*
I
–
–
*
N
–
–
*
0
0
*
*
0
–
2
–
1
3
*
*
–
–
–
–
*
*
*
*
*
*
*
*
*
*
*
–
–
–
–
1
2
1
–
[
*
*
A
*
2
1
4
–
L A R M
:
:
:
*
:
*
0
4
3
–
*
0
4
0
–
*
:
:
:
:
0
3
0
–
*
*
–
–
:
:
–
–
–
–
– :
–
*
:
M
*
–
*
E
– –
–
*
N U
:
:
*
:
:
–
–
*
*
–
–
*
*
*
*
N
*
0
0
0
–
*
I
–
–
*
*
–
–
*
*
*
*
*
*
]
*
*
*
2 1
2
–
6
5
–
–
–
–
–
–
–
–
–
*
*
–
*
*
–
–
–
–
–
–
–
–
–
–
*
*
–
–
*
*
1
*
*
–
–
–
–
– –
–
O
–
N
* *
0
0
*
*
0
–
0
–
0
0
*
*
–
–
–
–
– –
–
*
*
–
*
*
9
0
*
*
9
–
–
–
–
–
*
*
Hour
Minute
Day
Year
Month
Second
First alarm
Last alarm
Second alarm
Power loss list screen
*
*
*
* *
P L
*
4
*
*
*
*
*
P L
* *
P L
*
P
*
L
0
*
*
*
–
*
*
*
– 0
*
–
*
0
*
–
*
–
*
*
F
*
*
I
*
*
N
3
*
2
*
–
1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
[ P
*
O
*
W
*
E
*
R
*
*
*
*
*
7
*
:
*
3
*
5
*
:
:
2
*
L
*
O
*
S
*
7
*
*
*
S
*
]
*
2
*
1
*
*
7
*
0
*
–
*
*
*
*
*
*
*
*
*
*
*
–
*
1
*
1
:
*
:
*
:
4
*
3
4
*
0
*
:
:
*
–
*
–
* * * *
M *
E
*
N
*
U
2
*
:
*
–
*
3
*
*
*
0
*
0
*
–
*
*
*
*
–
*
*
3
7
*
0
*
–
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
–
*
–
*
*
*
*
*
–
*
–
*
1
*
*
*
–
*
1
First power loss
Last power loss
Second power loss
The dates and times of up to 8 alarm inputs or 4 power losses
(failures) can be displayed.
Operation
1
Turn on the VCR and monitor.
2
Press the [MENU] button to display the main menu on the monitor.
3
Press the [SHIFT 7] button to set the cursor on <OTHER>.
4
Press the [SET +/–] button to display the <OTHER> screen.
5
Press the [SHIFT 7] button to set the cursor on the item you want to display (ALARM IN LIST or POWER LOSS
LIST).
6
Press the [SET +/–] button to display the alarm or power loss list.
• Alarm in list: Up to 8 alarms are shown. When 9 or more alarms are input, the most recent data will replace the earliest data (beginning with the second item).
• Power loss list: Up to 4 power losses are shown. When 5 or more power losses are input, the most recent data will replace the earliest data (beginning with the second item).
7
Press the [MENU] button three times to restore the normal screen.
• Press the [MENU] button once to restore the <OTHER> screen and press once more to restore the main menu.
Resetting alarm input/power loss (failure) data
Press the [RESET/CANCEL] button on the alarm in list screen to reset the alarm input data stored in memory.
Press the [RESET/CANCEL] button on the power loss list screen to reset the power loss data stored in memory.
21
4 ON-SCREEN/MENU SWITCHES
4-6 Menu Switch Setting
You can customize the VCR’s functions to suit the requirements of your application using the four menu switch setting screens accessible from the main menu screen.
• ON SCREEN/F. DISPLAY MODE
• VIDEO/VTR MODE
• SRI/EXT, ALARM/SENSOR MODE
• BUZZER/IN OUT
Each menu switch setting screen can be accessed independently from the main menu.
[SHIFT 7] button
VIDEO CASSETTE RECORDER
SR-S990E
REC
RESET/
CANCEL
ON SCREEN
625
VHS
PAL
REC STOP REC
CHECK OPERATE
REW
REVERSE
PAUSE PLAY
FF
FIELD REV FIELD ADV
TRACKING
– +
V. LOCK
– +
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T +
EJECT OPERATE
MENU
SHIFT
TIME MODE
[MENU] button
–
S E T
[SET –] button
+
[SET +] button
Normal screen
22
[MENU] button
Main menu screen
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
4
*
*
*
*
*
*
*
*
*
*
*
*
C
V
*
L
*
O
*
C
O N
I
S
D
C
E
*
K
R
O
*
*
/
[
S
V
M
E
E E N
T
E
T
/
R
N
*
S
A
B
P
H
R
L
U
R
H O
O
I
A
Z
/
R
Z
O G
L
U
*
F
O
I
T
N
H
I
R
E
E
M
E
R
D
R
X
R
A
A
M
*
*
/
T
S
/
M *
Y
E
M
* M
E
I
N
N
*
T
S
T E
*
E
*
N
F
*
.
D I
M O D
O
S
*
E T
R
*
I
U
U
*
D
O
O
M
*
*
*
*
E
R
U
E
*
*
*
*
] *
*
*
*
T
R
*
*
*
*
*
*
S
E
*
M
*
*
*
*
*
*
P
*
*
*
*
*
*
*
O
*
D
*
*
*
*
*
*
*
*
*
*
* *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
M O D
E
*
*
*
*
*
*
*
*
*
E
*
*
*
* *
O
O
N
N
*
*
*
*
*
*
*
*
*
*
*
O
O
*
*
*
N
N
*
[MENU] button
ON SCREEN/F. DISPLAY MODE screen
3
4
2
*
*
1
*
.
*
T O N
*
2
M
.
A
D
*
N
A
[
U
T
O
E E
.
E
N
*
N
S C
* *
R
*
E
*
B
U
L
M
A
.
N
*
E N
*
C
*
*
*
*
4
.
.
T
R
I
E
M
C
.
W A R
F I N
E
*
*
S
T E
P E
L
E
E
D
5
1
.
6
*
.
M
.
A
P
L
O
O
R
D
E
A
W
[
C
R
E
F
*
M
R
T
N
*
I
D
B
O
A
C
N
L
N
T
L
T
R M L O S
*
Y
N G
E *
* *
M E
D
*
*
I
*
*
N U
E
S
*
*
*
*
*
*
*
*
* *
C N
*
*
*
*
*
*
M O D
*
*
*
*
*
M
*
*
.
A
*
T
T
4
I
.
*
*
*
S
*
P
*
L
*
A
*
*
*
*
*
*
*
E
*
]
*
*
*
*
*
*
*
5
N E
Y
*
]
*
*
*
*
*
*
*
*
*
*
*
*
*
1
O F
O F
*
*
*
O
*
N
F
F
*
*
O
*
N
*
*
0
*
0
* *
O
O
N
N
O N
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
[SET +/–] button
VIDEO/VTR
MODE screen
*
1
2
3
2
3
*
1
4
5
6
.
.
*
.
.
.
.
.
*
.
*
I
D
V
*
*
N
E
*
.
C N
P
A
O
U
*
P
T
P
*
T
W
T
*
U
A
U
*
*
E
O
[
T
I
L
*
R
*
V
*
L
S
[
E
*
R
I
E
V
*
*
M
O
E
D
*
*
*
T R
*
N
C
E
*
*
*
S
*
*
O
*
*
*
* M
W
R
C
*
*
*
*
*
E
H
M O D
*
*
*
O
*
C
E
*
*
*
D E
*
*
C
*
*
*
*
*
K
E ]
*
*
*
*
*
*
*
*
*
*
*
]
*
*
A
R
U
E
.
R E
T O
P E
*
A
R
T
E W *
* P L
*
A
P E A T * R E C
*
Y
*
*
*
*
*
*
*
*
*
* *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* * * *
L
*
I
O
N
F
E
F
O
*
O
O
O
F
*
F
F
F
F
*
F
F
F
*
*
*
*
O
O
F
F
F
F
O F F
SRI/EXT,
ALARM/SENSOR
MODE screen 2
3
*
*
1
1
2
3
5
6
7
.
.
.
.
*
.
*
.
.
.
*
S
E
C
[
*
R
X
N
A
R E
D U
.
T A
A
R
R
U
E
E
*
I
[
/
T *
S
E
R
X
I
T *
/ E
R
X
E
T
L
*
A
C
R
P
*
A
E
R
T
R
E
A
M
T
*
I
E
C
P
/
O
N
*
E
S
M O D E
N
D
E N
S
E
*
*
*
E
N
T
P
O
E
*
A
R
T
P E A E
E
*
*
W
P
R
* *
L
E
A
C
*
*
*
*
M O
*
Y
*
*
*
D
T
C
D
*
*
*
N
S
D
O
M O
*
*
*
R
*
*
*
*
D
*
*
E
*
*
*
M
*
O
]
*
*
*
*
*
*
O
*
F
N O R M A
*
D
*
E
*
]
O
*
F
*
*
*
*
*
*
E
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1
*
*
*
*
*
8
*
*
*
*
*
0
*
*
O
S
O
O
F
E
F
F
*
F
F
C
F
F
L
F
*
*
*
O
O
F
F
F
F
BUZZER/IN OUT screen
Only shown when the SA-
K97U is installed.
*
1
2
3
4
5
6
7
2
3
*
1
.
.
.
.
.
*
.
*
T
*
A
D U
T A
*
P
*
E
*
.
.
.
A
.
W
*
L
A
*
/
R N
*
S
*
C
R
A
S
M
2
E
3
R
P
A
E
A U
R
R
E
E
T O
P
P
E
E
*
*
I
*
T
*
*
*
E
E N
N
*
R
2
A
C
I
E
R
A
A
T
E
[
N
S
*
*
N
*
*
B
D
O
S
B
O N
D
P
R
U
*
R
G *
[ I
*
N
W
.
*
*
E W *
L
E
A
C
*
*
*
R
Z
*
Z
*
E
*
*
M
*
/
I
*
O
*
A
*
O
*
Y
*
N
*
U
*
*
*
R
*
*
*
*
*
*
*
*
*
*
*
*
]
*
T ]
*
T
*
E
*
D
*
E
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
9
*
O
O
O
*
*
F
F
F
*
O
6
F
0
*
F
*
*
8
*
*
0
*
S E
O F
C
O F
F
F *
*
*
O
O
F
F
F
F
F
F
*
F
0
Operation
1
Turn on the VCR and monitor.
2
Press the [MENU] button to display the main menu on the monitor.
3
Press the [SHIFT 7] button to select the menu switch setting screen you want to set or check.
• Set the cursor on the desired menu switch setting screen.
4
Press the [SET +/–] button.
[ The selected menu switch setting screen is shown on the monitor.
• The menu switch setting screen consists of several menu switch items.
5
To change the menu switch setting
1 Press the [SHIFT 7] button to set the cursor on the menu switch item setting you want to change.
2 Press the [SET +/–] button to specify the set value.
5
To set more than one menu switch, repeat the above steps
1 and 2.
6
To check or set the other menu switch setting screens
Press the [MENU] button to restore the main menu screen and repeat steps 3 to 5.
7
End menu switch setting.
To restore the normal screen from the menu switch setting screen, press the [MENU] button twice.
• The specified setting value is stored in the VCR’s memory and retained even if the operating power is turned off.
• For details on menu switch items, refer to pages 23 to 26.
4 ON-SCREEN/MENU SWITCHES
4-7 Contents of Menu Switches
[ ]: Factory setting • The lower section in the items and set values columns shows what’s on the VCR’s display.
Screens
ON
SCREEN
MODE
Items
TONE
(VCR's display)
O5D 1
DAY
O5D 2
TIME
O5D 3
REC SPEED
O5D 4
ALARM CNT
O5D 5
POWER
LOSS CNT
O5D 6
REC TALLY
F. DISP
FDiP 1
WARNING
FDiP 2
VIDEO MODE
INPUT
ViD 1
DETAIL
ViD 2
V. PULSE
ViD 3
Set values
0
30
70
[100]
[LINE]
Y/C
LiN
Yc
[OFF]
ON
OFF
ON
[OFF]
ON
OFF
ON
[ON]
OFF
ON
OFF
[ON]
OFF
ON
OFF
30
0
70
100
[ON]
OFF
ON
OFF
ON
[OFF]
ON
OFF
ON
[OFF]
ON
OFF
[ON]
OFF
ON
OFF
[ON]
OFF
ON
OFF
Sets whether or not the number of alarms is shown on screen.
ON: Shown.
OFF: Not shown.
Sets whether or not the number of power losses is shown on screen.
ON: Shown.
OFF: Not shown.
Function
The higher the numeric value, the brighter the display.
The brightness is shown on the line under the setting value.
0 %: ********** (black indication)
30 %: ***
70 %: *******
100 %: ********** (white indication)
Sets whether or not the day, month and year are shown on screen.
ON: Shown.
OFF: Not shown.
Sets whether or not the time is shown.
ON: Shown.
OFF: Not shown.
Sets whether or not the recording speed mode is shown on screen.
ON: Shown.
OFF: Not shown.
Sets whether or not the [REC] indicator lights in the Record mode.
ON: Lights.
OFF: Does not light .
Sets whether or not a warning indication (error code display) is shown when a problem occurs.
ON: Shown.
OFF: Not shown.
Selects the input video signal.
LINE: Inputs the composite video signal from the [VIDEO IN] terminal on the rear panel.
Y/C: Inputs the separate signal from the [Y/C IN] terminal on the rear panel.
Selects the picture quality for playback.
OFF: Playback with normal picture quality.
ON: Details in the playback picture become clearer. However, the S/
N ratio deteriorates.
Sets whether or not the V. pulse is added during ordinary playback
(3H mode).
OFF: V. pulse is not added. Normally set to this position.
ON: V. pulse is added.
• When a camera synchronized with the power supply is switched with a switcher, the picture may be distorted at the switching point. In this case, set this switch to “ON”. This locks the monitor, preventing the picture distortion at switching points (only in the 3H mode).
• V. pulse is always added in the Still mode and Timelapse mode.
23
4 ON-SCREEN/MENU SWITCHES
4-7 Contents of Menu Switches
[ ]: Factory setting • The lower section in the items and set values columns shows what’s on the VCR’s display.
Screens
VTR MODE
Items Set values
CNT MEM SW [OFF]
ON
VTR 1
OFF
ON
POWER ON
REC
VTR 2
[OFF]
ON
OFF
ON
Function
Sets whether or not the counter memory function is activated.
OFF: The counter memory function is not activated.
ON: The counter memory function is activated.
When the tape reel counter value reaches 0000 in the FF/REW mode, the VCR enters the Stop mode automatically.
* The counter memory function is not available during repeat recording/ playback, auto REW, alarm search, alarm scan and date/time search.
Enables or disables automatic external timer recording or automatic restart of recording after a power failure.
OFF: External timer recording or automatic recording after power failure is disabled regardless of whether power is supplied or not.
ON: Recording starts automatically when power is turned on.
AUTO REC
CHECK
VTR 3
AUTO REW
VTR 4
[OFF]
ON
OFF
ON
[OFF]
ON
OFF
ON
REPEAT PLAY [OFF]
ON
VTR 5
OFF
ON
REPEAT REC [OFF]
ON
VTR 6
OFF
ON
Sets whether or not Recording Check is automatically performed at the beginning of a tape in the Repeat Recording mode.
OFF: Automatic recording check function is disabled.
ON: Automatic recording check function is enabled.
Sets whether or not the tape is rewound automatically when the tape ends.
OFF: The tape stops at the end.
ON: The tape automatically rewinds and enters the Stop mode (auto
REW).
* When the repeat recording/playback function is set to “ON”, the repeat function has priority.
* If the menu switch <TAPE END MODE> on the <ALARM/SENSOR
MODE> screen is set to “STOP”, the Stop mode is engaged when the tape ends even when there is an alarm or sensor recording. The tape does not rewind.
Enables or disables the repeat playback function.
OFF: The repeat playback function is disabled.
ON: When the tape ends, it is automatically rewound and played back again from the beginning.
Enables or disables the repeat recording function.
OFF: The repeat recording function is disabled.
ON: When the tape ends, it is automatically rewound and recording starts again from the beginning. When set to “ON”, the [REPEAT] indication on the VCR’s display lights.
* If the menu switch <TAPE END MODE> on the <ALARM/SENSOR
MODE> screen is set to “STOP”, the Stop mode is engaged when the tape ends even when there is an alarm or sensor recording. The repeat recording is not executed.
* When this menu switch is set to “ON”, externally activated recording is not executed.
24
4 ON-SCREEN/MENU SWITCHES
4-7 Contents of Menu Switches
[ ]: Factory setting • The lower section in the items and set values columns shows what’s on the VCR’s display.
Screens
SRI/EXT
MODE
ALARM/
SENSOR
MODE
Items
SRI/EXT REC [OFF]
SERIES
EXT
(VCR's display)
SR ET 1
OFF
SERI
EIT
EXT REC END [NORMAL]
OPE OFF
SR ET 2
CNT TAPE END [OFF]
500
1000
..
.
9500
SR ET 3
OFF
500
.
..
9500
REC MODE
AL SE 1
DURATION
AL SE 2
Set values
NORn
POFF
[OFF]
ALARM
SENSOR
ALL
OFF
ALAR
SENS
ALL
5 SEC
10 SEC
15 SEC
30 SEC
60 SEC
120 SEC
[180 SEC]
TAPE END
MANUAL
..
5
.
180
TPEN nANU
Function
Selects series recording or automatic recording with an external VCR activation signal.
OFF: The series recording and automatic recording with an external signal functions are disabled.
SERIES: The series recording function is enabled.
EXT: The automatic recording function with an external signal is enabled.
* When the menu switch <REPEAT REC> is set to “ON”, externally activated recording is not executed.
Selects the mode engaged when externally activated automatic recording ends.
NORMAL: The Stop mode is engaged.
OPE OFF: The Stop mode is engaged and the operating power mode is turned off.
Outputs a tape end signal from the rear panel’s [TAPE END OUT] terminal when the tape reaches the set tape reel counter value during recording.
During series recording, a series recording signal is output to a connected
VCR for continuous recording.
OFF: The counter end output function is disabled.
500 : A tape end signal is output when the set tape reel counter value is
.
..
9500 reached during recording. A buzzer sounds when the menu switch
<END BUZ> on the <BUZZER/IN OUT> is set to “ON”.
For more information on the relationship between the tape reel counter value and the tape remaining time, refer to page 64.
Selects the alarm recording or sensor recording function.
• Alarm recording: When an alarm signal is input to the rear panel’s
[ALARM IN] terminal during recording, the mode switches to the 3H (SP) recording mode for realtime recording of the alarm event.
• Sensor recording: When an alarm signal is input to the rear panel’s
[ALARM IN] terminal in the Stop mode (Stop mode, Timer Recording
Standby or Operating Off mode), recording starts in the 3H (SP) mode.
OFF: Alarm or sensor recording is not executed.
ALARM: Alarm recording is executed.
SENSOR: Sensor recording is executed.
ALL: Both alarm and sensor recording are executed.
Selects the recording duration for alarm or sensor recording.
5 — 180 SEC: Alarm or sensor recording is performed for the specified time (5 sec. to 180 sec.)
TAPE END: Alarm or sensor recording continues to the end of the tape.
MANUAL: Alarm or sensor recording continues for as long as alarm signals are input. Set to this position when specifying the alarm recording time with a switcher.
*To ensure accurate alarm search and alarm scan operation, be sure to set the recording time to 5 seconds or more.
25
4 ON-SCREEN/MENU SWITCHES
4-7 Contents of Menu Switches
[ ]: Factory setting • The lower section in the items and set values columns shows what’s on the VCR’s display.
Screens
ALARM/
SENSOR
MODE
BUZZER
IN/OUT
Items
TAPE END
MODE
(VCR's display)
AL SE 3
TAPE END
BU 22 1
AL/SENSOR
IN
BU 22 2
WARNING
BU 22 3
CAMERA SW iO
RS-232C
B. RATE iO
1
3
Set values
[OFF]
STOP
OFF
STOP
600
1200
2400
4800
[9600]
600
..
.
9600
Function
Selects whether or not the Stop mode is forcibly engaged when the tape ends even if there is an alarm or sensor recording.
OFF: The forced Stop mode is not engaged.
• When the tape ends, the mode set with the menu switch <AUTO
REW> or <REPEAT REC> on the <VTR MODE> screen is engaged.
ON: The Forced Stop mode is engaged.
[OFF]
ON
OFF
ON
[OFF]
ON
OFF
ON
[OFF]
ON
OFF
ON
[OFF]
1 FIELD
2 FIELD
OFF
1FRD
2FRD
Sets whether or not the buzzer sounds when the tape ends in the
Record mode.
OFF: The buzzer does not sound.
ON: The buzzer sounds when the tape ends during recording. Also, the buzzer sounds when the tape reel counter value set with the menu switch <CNT TAPE END> on the SRI/EXT MODE screen is reached.
When the mode is changed by pressing the [REW] button,
[EJECT] button or [OPERATE] button, the buzzer sound stops.
Selects whether or not the buzzer sounds during alarm or sensor recording.
OFF: The buzzer does not sound.
ON: The buzzer sounds.
Sets whether or not the buzzer sounds when a warning occurs.
OFF: The buzzer does not sound.
ON: The buzzer sounds. When the warning is released, the buzzer sound stops.
Sets the camera switching signal output interval.
OFF: No camera switching signal is output.
1 FIELD: Set to this position to switch cameras every 1 field.
2 FIELD: Set to this position to switch cameras every two fields (1 frame).
Use this setting when connected to a JVC Frame Switcher or
Sequential Switcher.
This screen is shown only when the optional SA-K97U RS-232C board is installed.
Selects the RS-232C data transfer rate (600 bps, 1200 bps, 2400 bps,
4800 bps and 9600 bps).
5 PREPARATION
5-1 Cassette Loading/Unloading
Loading
Insert the cassette with its label side facing you.
Gently push the center of the cassette until the machine starts automatic loading.
S-VHS indication
625
VHS
PAL
REC STOP
OPERATE
REW REVERSE PAUSE PLAY
FIELD REV
FF
FIELD ADV
TRACKING
– +
V. LOCK
– +
TIMER SEARCH
DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T +
VIDEO CASSETTE RECORDER
SR-S990E
REC
EJECT OPERATE
(
[TIMER] indication
) indication
[EJECT] button
• The S-VHS indication lights up when an S-VHS cassette is inserted. During recording, the mode becomes the S-VHS mode.
• The S-VHS indication disappears when a VHS cassette is inserted. During recording, the mode becomes the S-VHS ET mode.
Notes:
• To avoid damage or injury, do not insert your hand or other foreign objects into the cassette loading slot.
• For best results, use a E-180 tape.
Auto operate on
When a cassette is loaded, the oprating mode automatically turns on and the ( ) cassette indication appears.
Auto play
When a cassette with no erasure prevention tab is loaded, playback starts automatically.
Unloading
5
Press the [EJECT] button.
[ The cassette is ejected.
• The tape reel counter is reset to “0000”.
If the operating mode is not on when the [EJECT] button is pressed, operating mode is automatically switched on and the cassette is ejected. Once the cassette is unloaded, the operating mode turns off again automatically.
If the Timer Recording Standby mode is engaged
(TIMER indication is shown on the display), the cassette will not be ejected when the [EJECT] button is pressed.
To unload the cassette, press the [TIMER] button to release the Timer Recording Standby mode, then press the [EJECT] button.
26 27
5 PREPARATION
5-2 Recording/Playback Speed Mode Selection
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
–
S E T
+
EJECT OPERATE
[TIME MODE +/–] buttons
[OPERATE] button
1
Press the [OPERATE] button to turn the operating mode on.
2
Select the Record or Playback speed with the [TIME MODE +/–] button. Refer to the table below.
The selected recording or playback speed mode is shown on the display.
Record/playback speed indication
Display
3H
L12H
L24H
24H
48H
72H
120H
168H
240H
Mode
Standard (SP)
12-hour linear slow
24-hour linear slow
24-hour timelapse
48-hour timelapse
72-hour timelapse
120-hour timelapse
168-hour timelapse
240-hour timelapse
E-180
Available recording time (hour)
3
12
120
168
240
24
24
48
72
Recording/ playback interval
(sec.)
Audio recording
—
0.1
Possible
0.18
0.18
0.34
0.52
0.82
Impossible
1.14
1.62
• Available recording time may vary depending on the type of cassette used.
• In the L12H and L24H Linear Slow mode, the tape runs continuously while sound is recorded. Pictures are timelapserecorded. When a VHS tape is used, the Linear Slow Mode cannot be used.
• When the L24H Linear Slow mode is used, distortions may occur in the playback picture.
When recording of sound is not required, it is recommended to the 24H timelapse mode.
• For best results, use an SE-180 or E-180 tape.
• Replace the cassette at least once every 15 days when using the 3H - 168H modes. In the 240H mode, replace the cassette with a new one at the completion of recording.
28
6 RECORDING
6-1 Switch Setting During Recording
625
PAL
REC STOP REC
CHECK
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET MENU
ON SCREEN
SHIFT
TIME MODE
– S E T +
VIDEO CASSETTE RECORDER
SR-S990E
REC
EJECT OPERATE
[REC] indicator
Connection
Connect the input and output connectors on the rear panel correctly. Refer to “CONNECTIONS” on pages 14 to 16.
Menu switch settings
Set menu switches as required.
5
ON SCREEN/F. DISPLAY MODE
• Select the brightness and ON/OFF for each indication
(date, time and recording speed, etc).
During recording, the selected on-screen data is recorded together with video signals.
If you do not want to display or record a specific item, set it to “OFF”.
• <REC TALLY> setting
Set whether or not the [REC] indicator lights in the
Record mode.
5
VIDEO MODE
• INPUT
Selects whether the input signal is LINE (composite video signal) or Y/C signal.
5
VTR MODE
• POWER ON REC
Set to “ON” for external timer recording or automatic restart of recording after a power failure. For details, refer to “6-9 How to Restore Recording After Power
Failure” and “6-10 External Timer Recording” on page
45.
• AUTO REW
Select the mode engaged when the tape ends.
“OFF”: The Stop mode is engaged.
“ON”: The tape automatically rewinds to the beginning.
When the <REPEAT REC> menu switch is set to “ON”, repeat recording takes place regardless of the setting of this switch.
• REPEAT REC
Set to “ON” to perform repeat recording. For details, refer to “6-7 Repeat Recording” on page 43.
• AUTO REC CHECK
Set to “ON” to perform Recording Check automatically at the beginning of a tape in the Repeat Recording mode.
5
SRI/EXT MODE
• SRI/EXT REC
- Set to “SERIES” to perform series recording. For details, refer to “6-6 Series Recording” on page 41.
- Set to “EXT” to execute automatic recording when activated by an external signal.
For details, refer to “6-8 Recording with External
VCR Activation Signal” on page 44.
5
ALARM/SENSOR MODE
• REC MODE
- For alarm recording, set to “ALARM” or “ALL”. For details, refer to “6-4 Alarm Recording” on page 38.
- For sensor recording, set to “SENSOR” or “ALL”. For details, refer to “6-5 Sensor Recording” on page 40.
5
BUZZER
• TAPE END
Set to “ON” if you want the buzzer to sound when the tape ends during recording.
5
IN/OUT
• CAMERA SW
Set the camera switching timing signal output to an external sequential switcher during recording.
- To switch cameras every 1 field or 1 frame, set this menu switch to “1 FIELD” or “2 FIELD”.
Regarding tapes for recording
When a VHS cassette is loaded in this unit, recording is performed in the S-VHS ET mode. Use a HG (highgrade) type tape for recording in the ET mode. (JVC videocassettes are recommended.)
A VHS tape recorded in the S-VHS ET mode cannot be played back on a normal VHS type video deck.
It is recommended that you mark the label on the cassette so that you know that it is recorded in the S-
VHS ET mode. Playback should be performed on this unit, or on a video deck equipped with function for S-
VHS or S-VHS simple playback (SQPB). However, playback may not be possible on some video decks equipped with function for S-VHS or S-VHS simple playback (SQPB). (This is due to differences in the way
S-VHS/VHS is distinguished by the various units.)
29
6 RECORDING
6-2 Recording Basic Operation
[STOP] button
[REC] button
[REC CHECK] button
[ON SCREEN 7]
button
625
VHS
PAL
REC STOP REC
CHECK OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– +
V. LOCK
– +
TIMER SEARCH DISPLAY LOCK CNT RESET MENU
ON SCREEN
SHIFT
TIME MODE
– S E T +
[ON SCREEN f]
button
VIDEO CASSETTE RECORDER
SR-S990E
REC
EJECT OPERATE
[PAUSE] button [PLAY] button
1
Press the [OPERATE] button to turn the operating mode on.
[ The [OPERATE] indicator lights.
2
Insert a cassette with safety tab in place.
[ The ( ) cassette indicator lights on the display.
* If a cassette is loaded when the operating mode is off, the operating mode is switched on automatically (auto operate on function).
3
Select the recording speed mode with the [TIME
MODE +/–] button.
For details, refer to “5-2 Recording/Playback Speed
Mode Selection” on page 28.
4
Select the on-screen display position with the [ON
SCREEN 7/f] button.
5
Press the [REC] button to start recording.
[ The recording indictor lights on the display, showing that the Record mode is engaged.
* No sound is recorded during Timelapse Recording
(except in the L12H/L24H mode).
To stop recording temporarily
6
Press the [PAUSE] button.
[ The record-pause indicator is shown on the display and the Pause mode is engaged.
* If the VCR remains in the Record-Pause mode for about 3 minutes, the head drum stops rotating to protect the tape. Although the Record-Pause mode remains engaged, there may be some distortion in the picture at the recording transition when you start recording again.
[TIME MODE +/–] button
[OPERATE] button
To check the recording
● To check recording in the Timelapse mode, the recording duration must be equivalent to at least 8 seconds at 3H (SP) speed. Recording check cannot be performed correctly if the recording duration is too short. (Example : In the 240-hour timelapse mode, the recording duration should be 11 minutes or more.)
● During recording check, the audio signal is not output.
5
Press the [REC CHECK] button during recording.
→ The tape is automatically played back in reverse for about 5 seconds, then the Play mode is engaged to allow you to check recording. After the sequence has played back, the recording mode is automatically re-engaged at the point where the recording was interrupted.
• During playback in the Recording Check mode, check the picture to ensure that the recording is satisfactory.
If the signals are not recorded properly, the built-in head cleaner cleans the heads and recording continues. In this case, the error code “E-09” is shown on the display for about 10 seconds.
[REC CHECK] button
During recording
Recording check
Normal
Recording
Error code “E-09” is shown for 10 seconds.
Defective
Auto head cleaning
Recording
To start recording again
7
Press the [PLAY] button.
[ The record-pause indicator on the display goes out and the Recording mode is engaged.
To stop recording
8
Press the [STOP] button.
[ The tape stops and the Stop mode is engaged.
30
If the recording speed is as shown below, the VCR cleans the heads automatically and continues recording whenever continuous 24-hour recording is performed.
Timelapse mode: 72H or more
Images recorded during the cleaning period may be unstable due to the interference with the servo control.
This is not a malfunction.
Note:
• When a tape recorded in this unit is played back on another VCR (except another SR-S990E/EK), noise may appear in the picture.
6 RECORDING
6-3 Timer Recording
This unit is provided with 2 different setting screens for timer recording program; one allows you to specify the day of week, the other allows you to specify a date (a holiday, for example). You can select the desired setting screen from the main menu screen.
• Program timer setting: Day-of-the-week (Sun. to Sat.) timer recording program and daily timer recording program are available (for up to 8 programs).
• Holiday setting: Timer recording can be programmed for a specified date.
* The holiday setting has priority over the program timer setting.
[SHIFT7] button [SHIFT4] button
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV
FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
–
S E T
+
EJECT OPERATE
RESET/
CANCEL
MENU
ON SCREEN
SHIFT
TIME MODE
– S E T
+
[MENU] button
[SET –] button
[SET +] button
[TIMER] button
Notes:
• Timer programming is not possible if the date and time are not set.
If you select program timer or holiday setting from the main menu when the date and time have not been set, the clock setting screen opens. Set the date and time.
• Do not try to program the regular timer or holiday timer when the Timer Record mode is engaged. To do so, you must first release the Timer Record mode by pressing the [TIMER] button.
Preparation
5
Make sure all equipment is connected correctly.
5 Check the current time.
5
Load a cassette with safety tab in place.
If a cassette is loaded when the operating mode is off, the operating mode is switched on automatically (auto operate on function).
Timer Recording Program Setting
5 Timer recording programming for the specified day of the week
(Example)
Recording is performed in the 48-hour timelapse mode from 8:00 a.m. to 5:00 p.m. on Saturday.
1
Turn on the VCR and monitor and engage the Stop mode.
2
Press the [MENU] button.
[ The main menu is shown on the monitor.
31
6 RECORDING
6-3 Timer Recording
Main menu screen
*
*
*
*
*
*
*
*
*
*
*
*
4
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
C L
O
*
N
V
S
I
R
*
O C
S
*
C
*
K
*
*
R E
D
I
E
/
O
E
/
X
[ M
S E
E N
E
T
/
N U
*
F
*
.
]
*
D
*
*
I
V
T
T
*
R
M
*
O
M
D
O
E
D
*
*
*
S
E
*
*
*
P
*
*
*
*
*
*
*
*
*
*
*
F
A
B
P R O G
H
H
L
U
O
O
A
Z Z
L
U
R
I
R
M
D
/
E R
R A
A
M
S E N
/
M
Y
E
I
*
*
T
N
T
S
E
S O R
*
I
E
R
O
M
T
*
U
E
*
*
*
T
M O D
* * *
R
*
*
*
*
*
*
*
*
*
*
*
O
I
T
N
H E R *
*
M * *
E N
*
U
*
*
*
*
*
*
*
*
*
*
*
*
M O D
*
*
*
*
*
*
E
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
E *
*
*
*
*
O N
O N
* *
*
O
*
N
O N
* *
PROGRAM TIMER screen
Recording speed
Stop time
Start time
Day of the week
D
*
*
*
*
S
*
*
U
*
*
N
M O N
0
0
*
*
[
S
–
–
T U E 0
–
–
– –
W
T
E
H
D
U
–
–
–
–
P
T
R
A
O
R
G
T
R
*
A
S
M
T
*
O
T
P
I
*
–
–
:
:
:
:
:
–
–
–
–
–
–
–
–
–
–
:
:
:
:
:
–
–
–
–
–
–
–
–
–
–
:
:
:
:
:
–
–
–
–
–
–
–
–
– –
F
S
R I
A T
A Y
D
*
A
*
–
I
–
–
*
–
–
–
L
T
–
–
–
Y
:
*
:
:
U E
–
–
–
S
–
–
–
E
:
:
:
T
–
*
–
–
–
–
–
*
* W E D *
:
:
:
*
T
–
–
–
*
H
–
*
–
–
U
*
*
*
*
*
*
*
*
*
M
*
E
S
R
P
]
D
*
*
–
–
–
–
–
–
–
–
1
6
*
*
*
P
–
–
–
–
*
G
*
M
–
–
*
–
–
–
–
–
–
–
–
–
–
–
–
S U
F R
–
–
–
–
–
–
N
I
–
–
–
–
–
*
5
–
–
–
–
–
–
–
–
–
S A
–
–
–
–
–
–
*
– – –
M O N
T
–
–
–
–
–
–
*
*
OFF : Operation is disabled.
1ST : 1st week
RPT : Every week
PROGRAM
NO.
1
2
3
4
5
6
7
8
*
*
S
D
*
*
*
*
*
*
S A T
M O N
T
W
U
E
E
D
T
F
H U
R I
0
–
0
0
–
–
A T
A
D
*
Y
A
*
*
*
[
S
–
0
–
8
–
–
–
–
I
–
L
*
–
–
P R O G
T
–
–
–
–
A
:
:
– –
–
Y
:
:
*
T U
:
:
:
:
E
R
0
–
–
–
–
–
–
–
S
T
0
–
–
–
–
–
–
–
E
R A
*
:
:
:
:
:
:
:
S
1
–
–
–
–
–
–
:
T
–
*
* W E D
M
T O P
7
–
:
:
0
–
*
0
–
–
–
–
–
–
–
*
*
*
:
:
:
:
T I
–
–
–
–
–
–
–
–
:
:
*
–
–
*
T H
–
–
*
*
U *
*
*
*
*
*
*
*
*
*
M E
S
R ]
P D
–
–
–
–
–
–
–
4
–
–
–
–
–
–
–
–
–
–
S
–
U
F R
–
–
–
–
N
I
*
*
8
–
–
–
*
*
1
6
5
–
*
R
–
–
–
*
P G
P
–
–
–
*
M
–
–
–
–
–
–
–
–
–
*
*
– – – –
–
M
–
O
–
N
S A T *
–
–
*
–
–
–
–
T
–
Timer
Program No.
TIMER
1 2
1 6 : 3 0 : 0 0
VCR display
3
Press the [SHIFT 7] button to select <PROGRAM
TIMER> in the main menu and press the [SET +/–] button.
[ The <PROGRAM TIMER> menu is shown on the monitor and “SUN” blinks.
4
Set the day of the week (SAT).
Press the [SET +/–] button to set the day of the week to
“SAT”.
5
Set the hour for the start time (8).
Press the [SHIFT f] button so that “hour” for “START” blinks. Press the [SET +/–] button to set the hour of the start time to “8”.
6
Set the minute for the start time (00).
Press the [SHIFT f] button so that “minute” for
“START” blinks. Press the [SET +/–] button to set the minute of the start time to “00”.
7
In the same way, set the hour (17) and minute (00) for the stop time.
* When the stop time is earlier than the start time or the same as the start time, “T” is added to the beginning of the stop time, showing that the stop time is for the next day.
8
Set the recording speed mode (48).
Press the [SHIFT f] button so that “SPD” blinks and press the [SET +/–] button to set the recording speed to
(48).
9
Set the program item.
Press the [SHIFT f] button so that “PGM” blinks and set the program item with the [SET +/–] button.
1ST: Timer recording is executed only once on the most recent specified day of the week (Saturday).
RPT: Timer recording is executed on the specified day of the week (Saturday) every week.
OFF: Programmed timer recording is not executed.
5
To program timer recording at another time or day, press the [SHIFT 7] button so that the next setting line blinks and repeat steps 4 to 9.
0
End timer program setting.
• Press the [MENU] button twice.
[ The normal screen is restored.
!
Press the [TIMER] button.
[The TIMER indication and effective timer-recording programmed numbers light on the display and the operating mode is automatically turned off to engage the Timer-Recording Standby mode.
32
6 RECORDING
6-3 Timer Recording
[SHIFT 7] button
[SHIFT f] button
VIDEO CASSETTE RECORDER
SR-S990E
REC
RESET/
CANCEL ON SCREEN
625
VHS
PAL
REC STOP
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV
FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T
+
EJECT OPERATE
MENU
SHIFT
TIME MODE
– S E T
+
[TIMER] button
PROGRAM TIMER screen
Recording speed
Stop time
Start time
Day of the week
*
*
S
D
*
*
*
*
S U N
M O N
T
W
U
E
E
D
T
F
H U
R I
0
–
0
0
–
–
A
A
D
*
*
*
T
Y
A
*
*
*
[
S
P R O G
T A R T
–
–
–
–
–
–
–
–
:
:
:
:
–
–
–
–
–
–
–
–
R A M *
:
:
:
*
:
S
–
T
–
–
–
O
:
:
P
–
–
–
–
–
–
:
:
–
–
T I
*
–
–
–
–
M E R ]
*
*
*
*
*
S
–
P
–
–
–
D
–
–
–
–
–
–
–
–
–
–
*
*
–
–
–
–
I
*
–
–
–
–
L
T
–
–
–
–
Y
U
:
:
:
:
*
E
–
–
–
–
S
*
–
–
–
–
E
W
:
:
:
:
T
E
–
–
–
–
*
D
–
–
–
–
*
*
:
:
:
:
*
T
–
–
–
–
*
H
–
–
–
–
*
U
*
*
*
*
*
*
–
–
–
–
S
F
–
–
–
–
U
R
–
–
–
–
N
I
–
–
–
–
*
*
1
6
5
–
–
–
–
–
*
P G
–
–
–
–
–
–
–
–
*
*
*
M
S
O
A
N
T
–
–
–
–
–
–
*
M
–
–
–
–
*
*
–
–
–
–
–
–
OFF : Operation is disabled.
1ST : 1st week
RPT : Every week
*
*
*
*
*
*
S
M
U
O
N
N
0
0
*
*
[
S
–
–
–
–
P R
T A
O G
R
:
:
–
–
T
–
–
R
*
:
:
A
S T O P
–
–
M
–
–
*
:
:
T
–
–
T
W
*
*
U
E
E
D
T H
F R
U
I
–
–
F
S
R
A
I
T
–
–
D A
* *
0
–
I
*
–
–
–
–
–
–
–
–
2
*
1
*
L Y
T U
:
:
:
:
–
–
–
–
–
–
–
–
:
:
:
:
–
–
–
–
:
:
0
*
0
*
:
:
*
E
S
*
E T *
W E D
*
–
*
–
*
*
–
–
–
–
–
–
–
–
:
:
:
:
*
:
:
*
–
*
T H U
*
–
*
–
–
–
–
*
I
–
–
*
*
*
M E R ]
S P D
–
–
–
–
–
–
–
–
*
*
*
*
*
*
*
*
*
*
–
–
–
–
*
–
S
F
–
–
–
–
*
–
U
R
–
–
–
–
*
–
N
I
–
–
–
–
*
–
*
*
1
6
–
–
5
–
–
–
–
–
*
P G M
–
–
–
–
*
–
*
–
–
*
–
*
–
–
*
*
M O
S A
N
T
*
*
*
–
–
–
–
–
–
–
–
–
*
*
*
*
S
M
U
O
N
N
*
*
T U
W E
E
D
*
*
0
0
–
–
0
–
–
–
[
S
P
T
T
F
F
H
R
R
M O
*
*
D
*
U
I
I
N
A
*
–
–
–
–
*
I
–
–
2
*
L
T
–
–
1
*
Y
U
–
–
–
–
R
A
:
:
O
R
–
–
G R
T
–
–
*
:
:
A M *
S
–
–
T
–
–
:
:
:
–
–
–
–
:
:
–
–
– – : –
:
:
–
0
–
0
:
:
:
*
E
*
S
*
*
E
:
T
W E
–
*
0
*
D
*
8
–
–
*
*
–
–
O
:
:
:
:
:
:
:
:
*
T
P
–
–
–
–
–
–
*
0
*
T H
I
*
–
–
*
0
–
–
–
–
*
U
M E
*
*
*
*
*
*
*
*
*
*
*
S
–
–
R
P
–
–
–
–
–
–
*
–
S
*
1
U
F R
N
I
–
–
*
2
–
–
–
–
–
–
–
–
]
D
–
–
–
–
–
–
5
–
*
*
–
–
1
6
*
*
*
P
–
–
–
–
* *
G M
–
–
–
–
–
–
–
–
–
–
–
–
–
–
*
0
–
–
*
R
*
P
*
T
*
*
M O
S A
N
T
*
*
[MENU] button
[SET +] button
[SET –] button
5
Programming timer recording for more than 24 hours
(Example)
Recording is performed in the 120-hour timelapse mode from 9:00 p.m. on every Friday to 8:00 a.m. on every Monday.
1
Follow steps 1 to 3 in “Timer Recording Program Setting” on page 31.
2
Press the [SHIFT 7] button so that the 7th line “SAT” blinks on the <PROGRAM TIMER>. Programs lasting for more than 24 hours can only be set on the seventh line.
3
Press the [SET +/–] button to set the day of the week to
“FRI” and press the [SHIFT f] button.
[ “Hour” for the start time blinks.
4
Press the [SET +/–] button to set the hour of the start time to “21” and press the [SHIFT f] button.
[ “Minute” for the start time blinks.
5
Press the [SET +/–] button to set the minute of the start time to “00” and press the [SHIFT f] button.
[ “Hour” for the stop time blinks.
6
Press the [SET +/–] button to set the hour of the stop time to “**”.
[ “**:** **** **” is shown for the items after “STOP”, the
“DAY” on the 8th line changes to the next day of the week (SAT) automatically and “**:**” is shown for
“START”.
7
Press the [SHIFT 7] button so that the day of the week on the 8th line blinks.
8
Press the [SET +/–] button to set the day of the week to
“MON” and press the [SHIFT f] button three times.
[ “Hour” for the stop time blinks.
9
Press the [SET +/–] button to set the hour of the stop time to “8”.
0
In the same way, press the [SHIFT f] button and [SET +/
–] button to set the minute of the stop time to “00”, the recording speed to “120” and “PGM” to “RPT (every week)”.
!
End timer program setting.
Press the [MENU] button twice.
[ The normal screen is restored.
@
Press the [TIMER] button.
[The TIMER indication and program number “7” light on the display and the operating mode is automatically turned off to engage the Timer-Recording Standby mode.
33
6 RECORDING
6-3 Timer Recording
PROGRAM TIMER screen
Recording speed
Stop time
Start time
Day of the week
*
*
*
*
*
*
S
M
U
O
T U
N
N
0
0
E 0
*
*
*
*
W E D
T H U
F R I –
–
–
S
D
A
A
T
Y
–
–
D A
* *
I
*
–
–
–
–
–
–
–
–
–
–
[
S T
–
–
P
–
–
R
A
O G
R
:
:
–
–
T
–
–
R
*
:
:
A
S T O P
–
–
M
–
–
*
:
:
T
–
–
:
:
:
:
–
–
–
–
–
–
–
–
:
:
:
:
–
–
–
–
–
–
–
–
:
:
:
:
–
–
–
–
L
T
–
–
Y
U
:
:
–
–
–
–
:
:
*
E
S
*
E T *
W E D
–
–
–
–
*
*
*
:
:
–
–
*
T H U
–
–
*
–
–
–
–
*
I
–
–
M E R
*
*
*
S
–
–
P
–
–
*
*
*
*
*
*
*
*
–
–
–
–
–
–
S
–
–
U
F R
N
I
–
–
–
–
–
–
–
–
–
–
–
–
]
D
*
*
–
–
1
6
*
*
–
–
–
–
–
–
5
–
–
–
–
–
*
*
M O
S A
N
T
*
*
–
–
–
–
–
–
–
–
*
–
–
*
–
–
*
P G M
–
–
–
–
–
–
–
–
–
–
–
–
ON: Enabled
OFF: Disabled
DAILY SET
PROGRAM
NO.
1
2
6
7
8
3
4
5
*
*
D
*
*
A
M O
*
*
N
*
*
Y 0
0
T U E 0
W
T
E
H
D
U
–
–
F R
S A
I
D A
*
*
D
*
A
*
–
T –
Y –
I
*
–
–
–
–
[
S
P
T
R
A
O
R
G
T
R
*
A
S
M
T
*
O
T
P
1
–
0
–
– –
–
–
–
–
:
:
:
:
:
:
:
0
–
–
–
–
–
–
0
–
–
–
–
–
–
:
:
:
:
:
:
:
1
–
–
–
–
–
–
7
–
–
–
–
–
–
:
:
:
:
:
:
:
0
–
–
–
–
–
–
– –
L
T
Y
U
: – – : –
*
E
S
*
E
W
T
E
*
D
–
*
*
: – –
*
T
*
H
*
U
–
–
–
0
–
–
–
I
*
M
*
E
S
R
P
]
D
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
P
*
G
*
M
–
–
–
–
–
–
–
–
–
–
–
–
4
–
–
–
–
8
–
–
–
–
1
6
5
–
–
*
–
O N
– –
– –
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
S
F
U
R
– –
N
I
*
*
– – – –
M
S
O
A
N
T
–
*
*
–
–
–
–
–
*
*
D
*
*
A
*
*
Y
*
*
0
M O
T U
N
E
0
0
W
T
E
H
D
U
–
–
–
–
–
1
–
[
S
F R
S A
D A
*
*
D
*
I
T
A
*
–
–
Y –
*
I
–
–
–
L
–
–
–
–
–
–
0
–
P
T
R
A
O
R
G
T
R
*
A
S
M
T
*
O
T
P
–
Y
–
:
:
:
:
:
:
:
:
*
–
0
–
–
–
–
–
–
–
0
–
–
–
–
–
–
–
:
:
:
:
:
:
:
:
1
–
–
–
–
–
–
–
S
*
E
W
T
E
*
D
7
–
–
–
–
–
–
–
*
*
:
:
:
:
:
:
:
:
*
–
0
–
–
–
–
–
–
–
*
–
–
*
–
–
–
–
–
–
0
–
I
*
M
*
E
S
*
*
*
*
*
*
*
–
–
–
–
R
P
]
D
–
–
–
–
–
–
4
–
–
–
–
8
–
*
*
–
–
–
–
–
*
*
1
6
5
–
–
*
P
*
G
*
M
O N
–
–
–
–
–
–
–
–
–
*
*
*
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
– –
S
–
U
–
N
–
– – – –
*
*
M
S
O
A
N
T
– –
*
*
–
–
5
Programming timer recording for more than one day
(every day)
This programming is to timer-record at the same time on specified days of the week.
(Example)
Recording is performed in the 48-hour timelapse mode from 10:00 a.m. to 5:00 p.m. on Monday, Wednesday and
Saturday.
1
Repeat steps 1 to 3 in “Timer Recording Program
Setting” on page 31.
2
Set the day of the week on <PROGRAM TIMER> to
“DAY” with the [SET +/–] button.
3
Press the [SHIFT f] button so that the “hour” for the start time blinks and set “hour” to “10” with the [SET +/–] button.
4
Press the [SHIFT f] button so that the “minute” for the start time blinks and set “minute” to “00” with the [SET +/
–] button.
5
Press the [SHIFT f] button and [SET +/–] button to set the hour of the stop time to “17”, the minute of the stop time to “00”, the recording speed to “48” and “PGM” to
“ON”.
6
Set the days of the week when timer recording is to be executed (Monday, Wednesday, Saturday).
Set the days with “DAILY SET” at the lower section of the screen.
• Press the [SHIFT 7] button so that “SUN” in the second line from the bottom blinks.
7
Press the [SET +/–] button to set “SUN” to “– –”.
8
Press the [SHIFT f] button to select the day of the week and set the operating day of the week with the
[SET +/–] button.
Set the items for “Tuesday”, “Thursday” and “Friday” to
“– –”.
• Timer recording will take place on the days of the week shown on the display. Timer recording will not take place on days of the week indicated by “– –”.
9
End timer program setting.
Press the [MENU] button twice.
[ The normal screen is restored.
0
Press the [TIMER] button.
[The TIMER indication and active timer program numbers light on the display and the operating mode is automatically turned off to engage the Timer-
Recording Standby mode.
34
6 RECORDING
6-3 Timer Recording
[SHIFT 7] button
VIDEO CASSETTE RECORCER
SR-S990E
REC
625
VHS
PAL
REC STOP REC
CHECK
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
–
+
V. LOCK
–
+
TIMER SEARCH DISPLAY LOCK CNT RESET MENU
ON SCREEN
SHIFT
TIME MODE
– S E T +
EJECT OPERATE
[MENU] button
[TIMER] button
RESET/
CANCEL
MENU
SHIFT
TIME MODE
–
ON SCREEN
S E T
[SET –] button
+
[SHIFT f] button
[SET +] button
Holiday Timer Recording Setting
This lets you preset the VCR to record on specified dates (such as holidays) at any time over a period of a year. Up to 16 dates can be set. When holiday settings and program settings overlap, holiday setting is given priority
Main menu screen
*
*
*
*
*
*
*
*
*
*
4
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
C
*
*
O
*
*
V
S
*
*
A
B
P
N
I
R
L
U
R
S
D
I
A
Z
O
C
E
/
R
R
O
E
M
Z
G
E
R
E
/
X
/
R
A
E
V
T
S
/
M
N
T
*
E
*
I
/
R
M
N
N
T
F
*
O
S
*
I
.
D
O
O
M
D
E
R
U
E
I
M O D
*
*
T
R
S
E
*
*
*
M O D
*
*
P
*
*
*
*
*
*
*
H
H
*
L
O
O
*
O
L
U
*
F
O T H
I N
*
C
I
R
E
*
K
R
*
*
D A
M
*
*
[
S
Y
E
M
E
*
E
T
S
N
*
E
T E R
M *
E
*
N
*
U
U
*
T
*
*
*
*
*
*
*
*
] *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
E *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
M O D
*
*
E
*
*
*
*
*
* *
O
*
N
O
*
N
*
*
*
*
*
*
*
*
*
*
*
*
O
O
*
*
N
N
*
HOLIDAY SET screen
:
:
:
:
*
*
*
:
:
–
–
*
*
0
–
–
0
0
*
:
:
–
*
*
*
*
*
*
*
*
*
*
1
9
1
*
*
*
5
7
1
3
1
1
*
3
5
*
–
–
–
–
–
–
* [ H
S
–
T
–
A
:
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
O L
R
–
T
–
I D
*
:
S
–
–
–
–
–
–
–
:
:
:
:
:
:
–
–
–
–
–
–
–
–
–
–
–
–
A Y *
T
–
O
:
P
–
S
*
–
:
:
:
:
1
1
0
2
6
8
2
4
:
:
:
:
:
:
–
–
–
–
T U E
–
–
*
–
–
:
*
W E
–
–
D
–
–
*
1
1
4
6
T H U
:
:
*
*
*
*
*
*
*
*
*
E
*
*
T
S
–
] *
P
–
D
–
*
*
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
F R
–
–
I
–
–
–
–
* S
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
*
*
1
* * *
P
–
G
–
M
–
–
–
–
–
–
–
– –
–
–
–
–
–
–
–
–
A
–
T
–
–
–
*
–
–
–
–
3
5
7
9
1
3
5
*
*
1
*
*
*
*
*
*
1
1
1
*
*
*
*
*
:
:
:
:
:
:
:
*
*
:
*
*
0
1
*
S
0
0
*
*
0 1
–
–
2
2
[
1
9
H O
1 –
–
–
L
T A
0
5
:
–
R
0
T
0
5
2
3
4
*
I
:
:
:
:
–
–
D
S
A Y *
T O P
S
*
T 0
–
–
0
–
–
–
–
:
:
:
:
:
0
2
4
6
8
0
:
:
:
:
E T
*
*
S
2
*
*
*
*
1
2
1
0
] *
P D
4
5
3
0
3
0
–
–
–
–
–
–
0
0
1
3
–
–
– 0
*
*
5
1
T
5
U
–
–
E *
5
5
:
:
–
–
5 : –
8
W
*
E
–
D
–
–
1
1
–
–
*
1 4
1
T
6
H
0
2
:
:
:
:
U
*
*
*
*
*
2
2
3
3
– –
–
F
–
R
–
–
I
–
–
*
*
*
*
– 1
1
1
0
1
9
9
* * *
P G M
–
–
–
–
O
–
–
–
N
–
–
–
–
–
–
1
1
1
2
–
–
–
–
–
*
– –
–
S
–
A
– –
–
T
–
–
*
–
–
Day Month
• When “PGM” is set to “OFF”, the setting is disabled and holiday timer recording is not executed.
(Example)
Recording is performed in the 240-hour timelapse mode from
00:00 a.m. to 0:00 a.m. the next day.
1
Press the [MENU] button to show the main menu on the monitor.
2
Call the <HOLIDAY SET> screen.
• Press the [SHIFT 7] button to select <HOLIDAY SET> in the main menu and press the [SET +/–] button.
3
Press the [SET +/–] button to set the hour of the start time to “0” and press the [SHIFT f] button.
[ “Minute” for the start time blinks.
4
Press the [SET +/–] button to set the minute of the start time to “00” and press the [SHIFT f] button.
[“Hour” for the stop time blinks.
5
Press the [SET +/–] button to set the hour of the start time to “00” and press the [SHIFT f] button.
“T” is shown at the beginning of the stop time.
* When the stop time is earlier than the start time or the same as the start time, the stop time is assumed to be the next day and “T” is added to the beginning of the stop time.
6
Press the [SHIFT f] button and [SET +/–] button to set the minute of the stop time to “00”, the recording speed to “240” and “PGM” to “ON”.
7
Set the date.
• Press the [SHIFT f] button or [SHIFT 7] button to select the line and enter the day for timer recording with the [SET +/–] button.
• Press the [SHIFT f] button so that the month item on the selected line blinks and enter the month for timer recording with the [SET +/–] button.
8
End holiday timer recording setting.
Press the [MENU] button twice.
[ The normal screen is restored.
9
Press the [TIMER] button.
[The TIMER indication lights on the display and the operating mode is automatically turned off to engage the Timer-Recording Standby mode.
* The timer program numbers are not shown on the display.Recording
Standby mode.
35
6 RECORDING
6-3 Timer Recording
[SHIFT 7] button
[RESET/CANCEL] button
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– +
V. LOCK
– +
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T +
EJECT OPERATE
RESET/
CANCEL
MENU
SHIFT
TIME MODE
–
ON SCREEN
S E T
+
[MENU] button
[SHIFT f] button
[TIMER] button
[SET –] button
[SET +] button
Canceling/Changing Timer Recording
Program
To stop timer programming before finishing
1
Press the [RESET/CANCEL] button.
[ The program being set is canceled.
2
Press the [MENU] button twice.
[ The normal screen mode is restored.
To cancel preset timer programs
1
Press the [TIMER] button so that the TIMER indication goes out on the display.
2
Turn on the VCR and monitor.
3
Press the [MENU] button to show the main menu screen and press the [SHIFT 7] button to select <PROGRAM
TIMER> or <HOLIDAY SET>. Then, press the [SET +/–] button.
[The <PROGRAM TIMER> or <HOLIDAY SET> menu is shown on the monitor.
4
Press the [SHIFT 7] button or [SHIFT f] button to move the cursor to the program you want to cancel.
5
Press the [RESET/CANCEL] button.
[ The specified timer recording program is canceled.
6
Press the [MENU] button twice.
[ The normal screen is restored.
To modify timer programs
1
Press the [TIMER] button so that the TIMER indication goes out on the display.
2
Turn on the VCR and monitor
3
Press the [MENU] button to show the main menu screen and press the [SHIFT 7] button to select <PROGRAM
TIMER or <HOLIDAY SET>. Then, press the [SET +/–] button.
[The <PROGRAM TIMER> or <HOLIDAY SET> menu is shown on the monitor.
4
Press the [SHIFT 7] button or [SHIFT f] button so that the section you want to change blinks.
5
Press the [SET +/–] button to change the value.
6
Press the [MENU] button twice.
[ The normal screen is restored.
To use the VCR when the Timer-Recording
Standby mode is engaged
• Press the [TIMER] button so that the TIMER indication goes out. After using the VCR, press the [TIMER] button again to engage the Timer-Recording Standby mode. The
TIMER indication will light.
• When all timer recording programs are completed, the
TIMER indication goes out.
36
6 RECORDING
6-3 Timer Recording
Notes on Timer Recording
5
If you make a mistake when programming or no program is set and the [TIMER] button is pressed, the
TIMER indication blinks for about 10 seconds and a warning buzzer sounds if <WARNING> in the
<BUZZER> menu is set to “ON”.
=
Perform programming for timer recording.
* Note that if the date is not set for holiday timer recording, the TIMER indication will not blink, the time standby mode is not engaged, and recording will not take place.
5
If programmed data overlap
When the [TIMER] button is pressed, the Timer-
Recording Standby mode is engaged and the
[OVERLAP] indication blinks for about 10 seconds, then lights.
(However, if program timer settings and holiday timer settings overlap, the [OVERLAP] indication is not shown. In this case, the holiday timer setting has priority. The [OVERLAP] indication is not shown when a daily timer recording program overlaps with another program (even during program timer setting). The program with the earlier start time has priority.)
=
Check the program contents.
(With program timer settings, the program with the earlier program time has priority.)
5
When more than one timer recording is programmed:
=
• The preset programs are executed consecutively beginning with the program with the earliest start time.
The number of the program being executed blinks.
* Program numbers are not displayed for holiday timer recording programs.
5
When the timer recording mode is engaged after the start time has passed:
When a power failure occurs within the set times and power is restored:
=
• Timer recording starts within the set times.
* If holiday timer and program timer settings overlap, the holiday timer setting has priority and starts.
* When program timer settings overlap, the program with the lower program number has priority and starts.
5
When the timer recording settings are changed during timer recording:
=
Changing the settings on the program timer setting screen or holiday timer setting screen during timer recording will have no effect. To change the settings, you must disengage the timer recording mode.
5
During timer recording
The [PAUSE] or [STOP] button has no effect.
=
Operation after pressing the [TIMER] button.
5
Timer recording
The operating mode is turned on about 20 seconds before recording starts and the VCR pauses. Recording starts about 2 seconds before the actual programmed start time.
5
If no cassette is loaded
The TIMER and [ ] indications blink and a warning buzzer sounds if <WARNING> in the <BUZZER> menu is set to “ON”.
=
Load a cassette with safety tab. Cassettes with no tab are ejected.
5
When the tape ends during timer recording:
=
The cassette tape is ejected.
When a cassette with safety tab is loaded, the timer recording re-starts.
* However, if timer recording is executed in the Repeat
Record mode, the cassette tape is not ejected at the tape end and repeat recording continues.
5 When the recording speed of program timer or holiday timer is set as L12/L24.
The cassette is ejected when a VHS cassette is loaded and the [TIMER] button is pressed.
=
• Insert an S-VHS cassette, or switch to a recording speed other than L12/L24.
37
6 RECORDING
6-4 Alarm Recording
Alarm recording functions during timelapse recording. When an alarm signal is input to the rear panel’s ALARM IN terminal, an index code is recorded on the tape and the VCR automatically switches to the 3H (SP) mode for realtime recording of the alarm situation. Normal timelapse recording is restored after the preset alarm recording duration has passed.
* Alarm recording will not start from the Pause mode.
“AL” indication
625
VHS
PAL
REC STOP
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– +
V. LOCK
– +
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T
+
VIDEO CASSETTE RECORDER
SR-S990E
REC
EJECT OPERATE
AL
TIME MODE
5
Menu switches are provided for alarm recording duration, buzzer ON/OFF in alarm recording, and
Forced Stop mode ON/OFF at tape end.
5
During alarm recording, the [AL] indication is lit on the
VCR and the [ALARM] indication is lit on the monitor display. After alarm recording is complete, the “AL” indication blinks on the display to show that an alarm signal has been input.
* If the alarm recording function is activated a hundred times a day or more, a malfunction may occur because the guaranteed range is exceeded.
If you want to use this unit more than a hundred times a day, set the recording speed mode to 3H, L12H or
L24H and perform regular maintenance, replacing parts as necessary.
On-screen
"ALARM" indication
Display "AL" indication
Extinguished
Extinguished
Record mode
Shown
Lit
Timelapse mode
Timelapse recording
3H (SP)
Alarm recording
Alarm signal input
Extinguished
Blinking
Shown
Lit
Timelapse mode
Timelapse recording
3H (SP)
Alarm recording
Alarm signal input
Extinguished
Blinking
Timelapse mode
Timelapse recording
* An index code (VISS) is recorded at the start point of the alarm recording as an alarm cue signal.
* During alarm recording, a +12 V signal is output from the rear panel’s ALARM REC OUT terminal.
* If a new alarm signal is input during alarm recording, alarm recording restarts from that point.
38
6 RECORDING
6-4 Alarm Recording
Preparation
Connect an alarm sensor to the rear panel’s alarm input terminal.
1
Press the [OPERATE] button to turn the operating mode on.
2
Open the main menu’s <ALARM/SENSOR MODE> and set the alarm recording-related menu switches.
1 REC MODE
Set to “ALARM” or “ALL” to activate alarm recording.
• When set to “ALL”, both alarm recording and sensor recording will be performed.
• The [ALARM] indication lights on the display.
2 DURATION
Set the alarm recording duration to 5 sec., 10 sec., 15 sec., 30 sec., 60 sec., 120 sec., 180 sec., TAPE END
(to tape end) or MANUAL (for as long as alarm signals are input).
* When the alarm recording time is set to “MANUAL”, the alarm cue signal (index code) will not be recorded correctly if alarm input lasts for less than 5 seconds.
* When alarm recording duration is set with an external switcher, set the alarm recording duration to
“MANUAL”.
3 TAPE END MODE
Selects whether or not the Stop mode is forcibly engaged when the tape ends even if there is an alarm recording during recording.
• When set to “STOP”, the Stop mode is engaged at tape end even if repeat recording or auto rewind is set.
• When set to “OFF”, VCR operation is determined by the repeat recording or auto rewind setting.
3
Set the other menu switches.
5
Setting the alarm buzzer
Set the menu switch <AL/SENSOR IN> in
<BUZZER> to “ON” to sound the alarm buzzer during alarm recording.
5
Setting the on-screen brightness and display items
Select the monitor display setting with the menu switch.
On-screen information is recorded together with the video signals.
You can change the on-screen display position with the [ON SCREEN 7/f] buttons on the front panel.
ALARM/SENSOR MODE screen
2
3
*
1
*
1
2
6
7
3
5
*
.
.
.
.
.
*
.
.
.
.
C
[
*
S
*
R
E X
*
I
R
D
A
R
R
N
A
E
U
T A
U
E
E
C
R
T
T
L
P
T
P
P
[
/
*
*
A
*
A
E
O
E
E
S
E
R
X
R
T A
R
M
T
*
*
A
A
E
M
O
I
D
O
E
R
T
E
T
C
P
N
E
*
*
I
/
/
*
*
E
S
E
N
D
W
P
R
E
*
E
S
X
*
N
E
E N
*
*
*
*
*
*
M
*
L A
E C
T
*
D
N
S
*
*
O
*
Y
*
*
*
*
D
O
*
*
D
*
*
*
M
*
*
*
R
*
*
E
*
*
*
*
*
*
*
*
O
*
*
*
*
*
*
D
*
E
*
*
*
M
*
*
*
*
*
*
*
*
*
O
*
*
*
*
*
*
*
]
*
*
*
*
*
*
*
*
A
6
*
*
*
*
*
*
*
*
*
*
*
O
N O R M A L
* *
D E
*
]
L
0
O
*
A
S
O
O
O
O
*
F
F
*
R
E
F
F
F
F
*
F
F
*
M
C
F
F
F
F
Set to “ALARM” or “ALL”.
4
Select the timelapse recording mode with the [TIME
MODE +/-] button on the front panel.
[ The selected recording speed mode is shown on the
VCR’s display and on the monitor.
5
Follow the procedure described in “Recording Basic
Operation” on page 30.
6
When an alarm signal is input to the rear panel’s
[ALARM IN] terminal, alarm recording is executed in accordance with the specified settings.
7
To stop alarm recording and clear the [ALARM] indication, press the [RESET/CANCEL] button.
• If the [RESET/CANCEL] button is pressed when the
[AL] indication is lit (during alarm recording), alarm recording stops, the [AL] indication goes out, and timelapse recording is restored. If the alarm buzzer is on, the buzzer sound also stops.
• If the [AL] indication blinks and the [RESET/CANCEL] button is pressed, the [AL] indication goes out.
8
The alarm input data can be checked in the main menu’s <OTHER> menu (refer to page 21).
Display the alarm list screen and press the [RESET/
CANCEL] button to reset the alarm input data.
* There may be some picture distortion at the start or end of an alarm recording. This is not a malfunction.
39
6 RECORDING
6-5 Sensor Recording
Sensor recording is executed only when the VCR is in the Stop mode (Stop, Timer Record Standby or Operating Off mode) and an alarm signal is input to the rear panel’s ALARM IN terminal.
Perform the settings for sensor recording in the same way as for “Alarm Recording” on page 39.
The mechanism of the SR-S990E/EK cannot be guaranteed if the sensor recording function is used frequently (100 times/ day or more).
Preparation
Connect an alarm sensor to the rear panel’s alarm input terminal.
1
Press the [OPERATE] button to turn the operating mode on.
2
Open the main menu’s <ALARM/SENSOR MODE> and set the sensor recording-related menu switches.
1 REC MODE
Set to “SENSOR” or “ALL” to activate alarm recording.
• When set to “ALL”, both alarm recording and sensor recording will be performed.
• The [SENSOR REC] indication lights on the display
2 DURATION
Set the sensor recording duration to 5 sec., 10 sec.,
15 sec., 30 sec., 60 sec., 120 sec., 180 sec., TAPE
END (to tape end) or MANUAL (for as long as alarm signals are input).
* The sensor recording time will be shorter than the specified value.
* When the sensor recording time is set to
“MANUAL”, the alarm cue signal (index code) will not be recorded correctly if sensor input lasts for less than 5 seconds.
* When sensor recording duration is set with an external switcher, set the sensor recording duration to “MANUAL”.
3 TAPE END MODE
Selects whether or not the Stop mode is forcibly engaged when the tape ends during sensor recording.
• When set to “STOP”, the Stop mode is engaged at tape end even if repeat recording or auto rewind is set.
• When set to “OFF”, VCR operation is determined by the repeat recording or auto rewind setting
3
Set the other menu switches.
5
Setting the alarm buzzer
Set the menu switch <AL/SENSOR IN> in
<BUZZER> to “ON” to sound the alarm buzzer during sensor recording.
5
Setting the on-screen brightness and display items
Select the monitor display setting with the menu switch.
On-screen information is recorded together with the video signals.
You can change the on-screen display position with the
[ON SCREEN 7/f] buttons on the front panel.
ALARM/SENSOR MODE screen
2
3
4
*
1
2
*
*
1
2
3
* * *
.
R
*
I
[
/
S
E
R
X
I
T
/
*
E X
R E
T
C
*
*
M O D
* * *
E
*
]
*
*
*
*
*
* * *
O F F
4
.
*
.
.
.
.
.
E
C
[
R
D
X
N
A
T
T
L
E C
U R
.
E
A
*
A
R
T
T
E
A
R M
M O
O
C
P
/
D
N
A
E
S
E
*
E
*
E
D
*
N
E
N
*
E
D
N
S
*
*
*
D
O
*
*
*
*
*
*
R
T
R
A
E
P
C
E
*
*
T
E
A
N
L
D
*
*
*
M
*
O
*
D
*
.
W
F
A
I
R
N
N
*
I
D
N
E
G
*
M *
E
*
N
*
U
*
*
*
*
*
M
O
*
T
*
*
*
.
M
4
*
*
I
E
*
T
*
A
*
*
*
O D
*
5
N
Y
*
*
N
*
S
*
E
]
*
*
O
*
E
E
6
*
*
*
*
R
*
M
O
]
N
0
*
*
*
*
*
S
S
O
*
*
*
A
F
L
F
*
O
E
F
O
O
*
*
R
C
F
N
N
*
* * *
Set to “SENSOR” or “ALL”.
4
Turn the operating mode on to engage the Stop mode.
5
• When an alarm signal is input to the rear panel’s
[ALARM IN] terminal, recording starts automatically in the 3H (SP) mode and the [AL] indication is lit. The
[ALARM] indication is shown on screen.
• After the specified recording duration expires, recording stops.
* As sensor recording starts from the Stop mode, it takes several seconds before actual recording starts.
6
To stop sensor recording and clear the [ALARM] indication, press the [RESET/CANCEL] button.
• In this case, even if the menu switch <TAPE END
MODE> is set to “STOP”, the operation executed at end of the tape is determined by the setting of the
<AUTO REW> or <REPEAT REC> menu switch in the
<VTR MODE> menu.
7
To release the Sensor Record mode, set the <REC
MODE> menu switch in <ALARM/SENSOR MODE> to
“OFF” or “ALARM”.
* During playback, there may be some noise or picture distortion at the point where one sensor recording stops and another starts. This is not a malfunction.
* When a new alarm is input during sensor recording, sensor recording restarts from that point.
40
6 RECORDING
6-6 Series Recording
The series recording function facilitates recording over much longer periods using several connected SR-S990E/EKs.
As soon as the tape ends in one VCR, the next VCR in the series starts recording. Using the counter end output function enables smoother switchovers during series recording, mostly eliminating interruptions between tapes.
Connections
5 Connect the first VCR’s [SERIES REC OUT] terminal to the second VCR’s [SERIES REC IN] terminal. Connect the second VCR’s [SERIES REC OUT] terminal to the third
VCR’s [SERIES REC IN] terminal. Repeat for all connected
VCRs. Connect the VCR’s [COM] terminals as well.
5 Connect a video camera and/or other source equipment to the first VCR’s video and audio input connectors.
Connect the first VCR’s video and audio output connectors to the second VCR’s video and audio input connectors.
Connect the second VCR’s video and audio output connectors to the third VCR’s video and audio input c o n n e c t o r s . R e p e a t f o r a l l c o n n e c t e d V C R s .
Connect the last VCR’s video and audio output connectors to the monitor’s video and audio input connectors.
Audio input signal
First VCR
Video input signal
Rear panel
Second VCR
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
VIDEO
Y/C
VIDEO
Y/C
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
COM
ALARM
IN
ALARM
REC OUT
ALARM
RESET
COM
TAPE
END OUT
CLOCK
RESET IN
WARNING
OUT
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
COM
ALARM
IN
ALARM
REC OUT
ALARM
RESET
TAPE
COM
END OUT
RESET IN
WARNING
OUT
CLOCK SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
ALARM
COM
IN
ALARM
REC OUT
ALARM
RESET
TAPE
COM
END OUT
WARNING
OUT
CLOCK
RESET IN
CLOCK
SERIES
REC IN
RESET OUT
SERIES
REC OUT
COM
WARNING
OUT
CLOCK
RESET IN
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
COM CLOCK SERIES
RESET IN
WARNING
OUT
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
COM CLOCK
RESET IN
SERIES
REC IN
WARNING
OUT
CLOCK
RESET OUT
SERIES
REC OUT
First VCR
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
VIDEO
Y/C
Second VCR Third VCR
Operation
1
To activate series recording, set the <SRI/EXT REC> menu switch in <SRI/EXT MODE> to “SERIES”.
(This setting should be done for all connected VCRs.)
*
1
2
3
2
3
*
1
5
6
7
.
.
*
.
*
.
*
S
E
C
[
R
*
R
X
N
A
E
*
I
T
T
L
C
.
.
.
.
.
D
T
U
A
R
P
A
E
T
*
A
R
R
U T
E P
E P
O
E
E
*
A
A
[
/
S
E
R I
X T
E C *
*
/
*
*
R
T
A R
A P
M /
E
S
E
R
E
S
E
X
E
N
E
N
T
C
D
N
S
*
*
*
D
O
M
*
*
*
R
O
*
*
*
*
D
*
*
*
M
E
*
*
*
O
]
S
N
*
D
*
E
O
*
E
*
R
5
]
*
I
R M
0
*
*
E
A
0
*
*
S
* M O D E * * * * * * * * * * * O F
L
0
*
F
I
E
R E
T
E
O
N
*
*
N
D
W
R
*
*
*
E
*
M
*
P L A
C
*
O
*
Y
*
*
*
*
D
*
*
E
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1
*
*
*
*
5
*
*
*
*
S
O
E
F
O
O
O
F
F
F
C
F
F
F
F
Set to “SERIES”.
Set the counter value.
Last VCR
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
Audio output
VIDEO
Y/C
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
ALARM
COM
IN
ALARM
REC OUT
ALARM
RESET
TAPE
COM
END OUT OUT
CLOCK
RESET IN
WARNING
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
Video output
Monitor TV
• During recording, the input video signals can be checked on a monitor.
• When the second and subsequent VCRs are turned on, input audio can be checked on the monitor in the 3H, L12H and L24H modes. During timelapse recording (except for the L12H and
L24H modes), audio cannot be checked.
5
Normally the next VCR starts recording when the tape ends. If the menu switch counter end output function is on, a series recording signal is output when the selected tape reel counter value is passed, and the next VCR starts recording. Select the counter end value from “500”,
“1000” ... “9500” with the <CNT TAPE END> menu switch.
• The tape reel counter value from the beginning of the tape to the end is about 5800 on a E-180 cassette tape.
(Reter to page 64.)
2
Press the [MENU] button to restore the normal screen.
3
Load cassettes with safety tab in place in all connected
VCRs.
5 To use the counter end output function, set the
4 counter to the tape reel counter display with the
[DISPLAY] button.
When a cassette is loaded, the counter is reset to
“0000”.
Start recording on the first VCR.
Notes:
• If a cassette has not been loaded in any VCR in the series, series recording will stop when that VCR is reached.
• If VCRs are connected in series as shown above, the second and subsequent VCRs will record the previous VCR’s on-screen information in addition to their own. To avoid this, use a distributor to distribute only video signals to each VCR.
41
6 RECORDING
6-6 Series Recording
5
When the first VCR ends recording, the second VCR starts recording automatically, then the third and so on.
• When the tape end output is set, series recording signals are output from the [SERIES REC OUT] terminal at the specified tape reel counter value, signaling the next VCR to start recording.
The first VCR continues recording until the tape ends.
• If the <AUTO REW> menu switch in <VTR MODE> is set to “OFF”, the Stop mode is engaged when the end of the tape is reached during recording. If <AUTO
REW> is set to “ON”, the tape rewinds to the beginning and stops.
• Counter value
When the tape is rewound to the beginning in the
Repeat Recording or Auto Rewind mode using the counter end output function, thetape reel counter value is reset to “0000”.
Non-stop continuous series recording
The series recording function allows you to record indefinitely using two VCRs. Recording alternates between each VCR.
To use this function, connect and set the VCRs as follows.
5
Connection
5
Setting
• Connect the [SERIES REC OUT] terminal of the first
VCR to the [SERIES REC IN] terminal of the second
VCR, and the [SERIES REC OUT] terminal of the second VCR to the [SERIES REC IN] terminal of the first VCR. The [COM] terminals of both VCRs should be connected.
• Set the <SRI/EXT REC> menu switch on both units to
“SERIES”.
• Set the <AUTO REW> menu switch in <VTR MODE> to “ON”.
• Set the setting of the VIDEO/VTR MODE menu switches <AUTO REC CHECK> and <REPEAT REC> to “OFF” on both units.
COM
WARNING
OUT
CLOCK
RESET IN
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
COM
CLOCK
RESET IN
WARNING
OUT
SERIES
REC IN
CLOCK
RESET OUT
SERIES
REC OUT
5 For uninterrupted endless series recording, use the counter end output function together. Set <CNT TAPE
END> so that the counter end signal is output just before the tape end.
• Set <CNT TAPE END> in the <SRI/EXT MODE> menu to “5500” (when a E-180 tape is used).
First VCR
Second VCR
* When the tape is rewound to the beginning in the
Auto Rewind mode using the counter end output function, the tape reel counter is reset automatically to “0000”.
• Connect audio and video terminals as shown in the connection diagram on page 41.
Note:
• Continuous series recording over a long period may produce excessive wear and tear on the tapes and
VCRs. Be sure to replace the tapes periodically
(refer to page 28).
42
6 RECORDING
6-7 Repeat Recording
When the tape comes to the end during recording, it is automatically rewound and recording starts again from the beginning.
5
To execute repeat recording, set <REPEAT REC> in
<VTR MODE> to “ON”.
• The [REPEAT] indication in the VCR’s display lights.
5
Setting the <TAPE END MODE> menu switch in
<ALARM/SENSOR MODE>
• If this menu switch is set to “STOP”, the Stop mode is forcibly engaged when the tape ends even if there is an alarm or sensor recording.
To continue repeat recording even if an alarm recording or sensor recording takes place during recording, set <TAPE END MODE> to “OFF”.
When the Tape End Forced Stop mode and Repeat
Rec mode are engaged and an alarm or sensor recording takes place, the [REPEAT] indication goes out.
VIDEO/VTR MODE screen
2
3
*
1
*
1
2
5
6
3
4
.
.
*
.
.
.
.
.
*
.
.
A
A
R
R
*
I
D
V
*
*
N
*
P
E
.
*
T
P
*
*
U
A
U
*
[
T
I
L
*
V
*
L
[
I
*
*
S E
V
C
P
N
O
T
W
*
E
M
R
E
*
M
O
D
*
*
*
T *
E
*
*
*
R
N
S
*
O
*
*
*
*
W
R
*
*
*
*
M
*
*
*
*
C
O
*
*
*
*
*
D
*
*
*
E
*
*
*
M O D E * ]
*
E
* *
*
U
U
T
T
E P
E P
O
O
E A
E A
*
*
R E
R E W *
T
T
*
*
C *
P L
R E
C H
* *
A
C
Y
*
E
*
*
*
C
*
*
*
*
*
*
*
*
*
*
K
*
*
*
*
*
*
*
*
*
*
*
]
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
L
*
I
*
N
*
E
O F F
O F F
* * *
O
O
F
F
F
F
O
O
O
O
F
F
F
O
F
F
F
N
*
*
*
*
*
*
*
*
*
*
*
*
Set to “ON”.
ALARM/SENSOR MODE screen
5
6
7
2
3
2
3
*
1
*
1
*
.
.
.
.
.
.
*
S
E
C
A
R
R
*
R
X
N
E
*
I
T
T
P
*
*
[
/
S
E
R
E
T
U
E
T
P
O
E
*
A
A
R
X
E
A
R
T
E
E
*
I
T
C
P
*
/
*
*
R
E
R
E
E S
W
P
*
L
E
X
E
T
C
*
*
N
E
D
N
*
D
M
*
O
*
D
*
*
*
*
*
*
*
.
.
*
.
[
R
D
T
A
E
U
A
L
C
R
P
A
*
R
M
A
E
T
*
M
O
/
D
I O
E N
S
E
N
D
E
*
*
*
N
*
*
S
*
*
O
*
*
M O D
R
*
*
A
C
*
Y
*
*
*
*
*
*
*
*
E
*
*
*
*
*
*
*
*
M
*
*
*
*
*
*
*
E
* *
]
*
*
O
*
*
*
*
*
*
*
N
*
D
S
*
1
*
*
*
*
*
*
*
*
O R
* *
E
E
6
*
*
*
*
*
*
*
*
]
N
0
*
O
*
F
*
F
M
O
A
F
L
F
*
S
*
O
*
R
S
O
O
O
O
E
F
F
F
F
C
F
F
F
F
Set to “OFF”
* When repeat recording is executed, any previously executed alarm recordings will be erased.
5
Automatic recording check function
This unit is provided with an automatic recording check function which automatically determines whether or not recording is satisfactory at the tape beginning in repeat recording.
• To activate the automatic recording check function, set the <AUTO REC CHECK> menu switch in <VTR
MODE> to “ON”.
5 Operation of the automatic recording check
function
• Recording is performed from the beginning of the tape for several seconds during repeat recording. Then the recorded section is automatically played back to check whether or not the signals have been recorded properly. If the recording is satisfactory, recording resumes.
• If the recording is unsatisfactory, the heads are cleaned automatically. Recording is restarted for several seconds and then the recording is checked again. If the recording is still unsatisfactory, the error code “E-
09” is shown on the display and recording resumes.
5
When the <AUTO REC CHECK> menu switch is set to “ON”
Repeat recording
Tape beginning position
Auto recording for several seconds
Recording check
Defect
Auto head cleaning
Auto recording for several seconds
Normal
Normal
Recording check
Defect
Auto head cleaning
Display
The error code “E-09” remains on the display.
Recording
Recording
Recording
Note:
• Continuous repeat recording over long periods may produce excessive wear and tear on the tape and
VCR. Be sure to replace the tape periodically (refer to page 28).
43
6 RECORDING
6-8 Recording with External VCR Activation Signal
Recording start/stop can be controlled externally by inputting a VCR activation signal to the [SERIES REC IN] terminal on the
SR-S990E/EK’s rear panel.
* If the external recording function is activated a hundred times a day or more, a malfunction may occur
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
VIDEO
Y/C
To [COM] terminal
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
ALARM
COM
IN
ALARM
REC OUT
ALARM
RESET
TAPE
COM
END OUT
CLOCK
RESET IN
WARNING
OUT
RESET IN
CLOCK
SERIES
RESET OUT
SERIES
RESET OUT
To [SERIES REC
IN] terminal because the guaranteed range is exceeded.
If you want to use this unit more than a hundred times a day, set the recording speed mode to 3H, L12H or
L24H and perform regular maintenance, replacing parts as necessary. Use an S-VHS tape when setting to L12H, L24H.
External control equipment
Connection
VCR control signal (ground signal)
Start of recording
LV: 0 V
Stop or operating mode off
Connect the [SERIES REC IN] terminal and [COM] terminal on the SR-S990E/EK’s rear panel to the external control equipment.
Alarm search/date and time search
• Alarm recording or sensor recording should continue for at least 5 seconds.
• When recording is performed in the long-time timelapse mode, date/time search will not function correctly if the recording duration is too short.
To ensure that the date/time search operates correctly, the recording duration must be equivalent to at least 5 seconds at Standard (3H) speed.
(Example) With a 240-hour normal timelapse recording, a recording time of 7 minutes or more is necessary.
Operation
1
Set the <SRI/EXT REC> menu switch in <SRI/EXT
MODE> to “EXT” to use the external recording function.
• Use the <EXT REC END> menu switch to select the mode engaged when externally activated recording ends.
When set to “STOP”, the VCR enters the Stop mode.
When set to “OPE OFF”, the operating mode is turned off.
2
Press the [MENU] button to set the on-screen display to the time/date display.
3
Load a cassette with a safety tab in place and engage the
Stop mode or turn the operating mode off.
• When a VCR activation signal (ground input) is input to the rear panel’s [SERIES REC IN] terminal, recording starts automatically and continues for as long as the activation signal is input.
When the activation signal stops, the Stop mode is engaged or the operating mode is turned off (according to menu switch setting).
• When the activation signal is input again, recording starts.
SRI/EXT MODE screen
5
6
7
1
2
3
*
1
2
3
*
.
.
.
*
.
.
.
*
.
.
.
*
S
E
C
[
R
*
R
X
N
A
*
I
T
T
[
/
*
*
D
T
U
A
R
P
A
E
S
E
R
T
L A R
E C * M
R
X
E
A
M
O
I
T
C
P
/
D
/
*
*
E
S
E
T
*
I
E
O
N
N
D
E
R
E
X
E
N
S E
T
C
D
N
*
*
*
D
*
*
*
E N
*
*
M
S
*
*
O
O
*
*
D
R
*
*
E
*
*
*
M O D
*
*
*
*
*
*
*
*
*
*
M
*
*
*
E
*
*
*
O
*
*
*
]
*
N
*
*
*
O
*
D E
*
*
1
*
1
*
*
*
5
*
*
*
R
E
E
7
]
0
*
O
S
O
*
X
X
0
*
F
E
F
*
T
T
0
*
F
C
F
A
R
R
U
E
E
T O *
P E A
P E A
R
T
E
E
*
*
W
P
R
*
L
E
*
A
C
*
Y
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O
O
F
F
O F
F
F
F
Set to “EXT.”
• In addition to the Stop mode and the operating mode off status, the external recording function also operates in the Pause mode.
• If recording is already in progress when the VCR activation signal is input, recording continues and stops when the activation signal is no longer input.
Note:
When the TIMER indication lights or the menu switch
<REPEAT REC> in the <VTR MODE> menu is set to
“ON”, externally activated recording is not executed.
To execute repeat recording via the external recording function, set <REPEAT REC> to “OFF” and <AUTO REW> to “ON”.
44
6 RECORDING
6-9 How to Restore Recording After Power Failure
If a power failure occurs during recording, recording will restart in the same mode as soon as power is restored.
To use this function, set the <POWER ON REC> menu switch in <VTR MODE> to “ON”.
If this menu switch is set to “ON” and operating mode is turned off and on again in the Stop mode, the VCR enters the Record mode automatically. Be careful.
VTR MODE screen
2
3
*
1
*
1
2
5
6
3
4
.
.
*
.
.
.
.
.
D
V
*
I
*
N
*
P
*
U
E T A
* *
.
P
*
U
*
[
T
V
*
I
*
I
*
L
L S
[
*
E
V
D
*
*
*
T
E
*
*
*
R
*
*
O
*
*
*
*
M
*
O
*
D
*
*
*
*
*
*
*
M O D E
*
*
*
.
.
C
P
R
R
N
O
A U
A U
E
E
T
W
P
P
*
E
T O
T O
E
E
M
R
*
*
A
A
E
*
R
R
M
O
E
*
N
C
S
*
W
R
* C
T
T
E W
*
*
P
R
*
L A
E
*
C
*
E
*
C
H E
*
Y
*
*
*
*
*
*
C K
*
*
*
*
*
*
*
* *
*
*
E
*
]
*
*
*
]
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
L
*
I
*
N
*
E
*
*
*
*
*
*
*
O
O
*
O
O
F
O
F
N
O
O
F
F
*
F
F
F
F
*
F
F
*
*
*
O F F
O F F
Set to “ON”.
6-10 External Timer Recording
External timer recording can be performed by connecting the SR-S990E/EK to an external timer.
1
Check that a cassette is loaded in the VCR.
* If the cassette’s safety tab has been removed, recording will not take place.
* This function does not work when the Timer Record mode is engaged.
2
Set the <POWER ON REC> menu switch in <VTR
MODE> to “ON”.
Power is supplied from the external timer at the specified time and recording starts.
• Recording is performed at the preset recording speed.
If alarm recording or sensor recording is executed before the power is supplied, the Alarm Record mode or Sensor Record mode is released and normal recording starts.
6-11 Tape End Buzzer
You can switch the buzzer sound which lets you know when the tape ends during recording ON/OFF.
The “END” indication blinks on the on-screen display.
5 To sound the buzzer, set the menu switch <TAPE END> in <BUZZER> to “ON”.
• If <CNT TAPE END> in the <SRI/EXT MODE> menu is set to any position except “OFF”, the buzzer sounds when the reel counter value is reached.
5 The buzzer continues to sound. To stop the buzzer sound, set the menu switch <TAPE END> to “OFF”, perform another operation (such as pressing the [REW] button) or press the [OPERATE] button.
5 During repeat recording and auto rewind, the buzzer sounds for about 2 seconds.
5
BUZZER screen
*
1
2
3
4
5
6
7
2
3
*
1
*
.
*
T
.
.
R
R
*
A
E
E
*
P
P
P
*
E
.
.
*
.
.
A L / S E
W A R
*
C
R
D
*
A
S
*
M
2
N
*
E
3
R
2
I
*
U R A T .
.
.
T A P
A
E
U T O
*
*
E
E
*
*
A
A
*
E
[
N
B
D
U
*
Z
*
Z
*
E
*
R
*
N S
N G
*
A
C
[
*
*
O
*
I
R
*
N
*
*
/
I
*
O
S
B
W
.
*
R
*
A
N
*
U
*
T
T
*
E
*
*
I
E
O
N
N
D
*
*
R
T
E
E
*
*
W *
P
R
L
E
*
M O
*
*
*
A
C
Y
*
*
D E
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
]
*
*
*
*
*
]
*
*
*
*
*
*
*
*
*
*
*
1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
O
O
O
F
N
F
O
*
*
F
*
*
F
*
*
*
*
*
*
*
8
*
9
0
*
*
*
*
O F F
6
S
0
E
0
C
O
O
F
F
F
F
O
O
F
F
F
F
Set to “ON”.
Shown only when the SA-K97U is installed
5
Tape “END” indication
0
0
0
1
:
-
0
0
0
1
:
-
0
2
1
0 0
E ND
0 SAT
45
7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK
[STOP] button Playback mode indicator
[OPERATE] indicator
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP REC
CHECK OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
–
S E T
+
EJECT OPERATE
[OPERATE] button
[PLAY] button
7-1 Preparation
Connection
Connect the output connectors on the rear panel correctly.
Menu switch setting
Set the menu switches in <VIDEO/VTR MODE> as required.
5
[DETAIL] ... Factory setting: OFF
To make details of the playback picture clearer, set to
“ON”. However, the S/N ratio deteriorates.
5
[V. PULSE] ... Factory setting: OFF
Set to “ON” to add V. pulse in the 3H (SP) play mode.
5
[CNT MEM SW] ... Factory setting: OFF
Counter memory ON/OFF.
• Set to “ON” to use the counter memory function.
5
[AUTO REW] ... Factory setting: OFF
Automatic rewind ON/OFF.
• Set to “ON” to rewind the tape to the beginning when the tape ends.
5
[REPEAT PLAY] ... Factory setting: OFF
Repeat playback ON/OFF.
• Set to “ON” to execute repeat playback.
* To listen to the sound recorded in the L12H and
L24H modes, play the tape back in the same mode used for recording (L12H or L24H).
* When a tape recorded in the 3H mode is played back in the L12H or L24H mode, noise appears in the picture.
Press the [TIME MODE +/–] button to set the playback speed to 3H and start playback.
* Noise may appear in the picture with tapes not
recorded on the SR-S990E/EK.
* Tapes recorded in the LP mode cannot be played back. In this case, the [LP] indication blinks on the display
Cautions for playback of S-VHS ET recorded tapes
• Avoid operations that applies a load to the tape, such as search playback, etc. This will result in deteriorating picture quality.
• Due to the performance of the unit, noise may appear in the playback picture during search playback and field advance.
46
[TIME MODE+/–] button
7-2 Playback
1
Press the [OPERATE] button to turn the operating mode on.
The [OPERATE] indicator lights.
2
Press the [TIME MODE +/–] button to set the play mode to 3H (SP) mode.
The [3H] indication is shown on the display.
• To play back a tape recorded in the timelapse mode at slow speed, press the [TIME MODE +/–] button to set the desired mode (L12H, L24H ..... 240H)
(slow play).
• Avoid using slow-motion playback continuously for long periods (more than several hours).
3
Load the recorded cassette correctly.
* If a cassette is loaded when the operating mode is off, the operating mode is switched on automatically (auto operate on function).
If the cassette’s safety tab has been removed, the operating mode is turned on and play starts automatically (auto play function).
4
Press the [PLAY] button to start play.
The play indicator is shown on the display and the Play mode is engaged.
* No sound is output in the Timelapse Play mode
(except for L12H and L24H modes).
To stop playback
5
Press the [STOP] button.
The tape stops and the Stop mode is engaged.
7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP REC
CHECK OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
–
+
–
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET
[REW] button
[REVERSE] button
[FF] button
[PLAY] button
[PAUSE] button
7-3 Special-Effects Playback
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T +
EJECT OPERATE
Still playback
1
Press the [PAUSE] button during playback.
The still indicator is shown on the display and the still picture is shown.
2
Press the [PLAY] button to restore the Normal Play mode.
The Stop mode is automatically engaged if the VCR remains in the Still mode for 3 minutes (approx.).
Field advance playback
1
Press the [PAUSE] button in the Play mode to engage the Still mode.
2
While pressing the [PAUSE] button, press the [FF] button or [REW] button.
The operation varies depending on how the [FF] or
[REW] button is pressed.
5
Each time the [FF] button or [REW] button is pressed, the picture is advanced or reversed one field.
5 When the [FF] button or [REW] button is pressed for more than 2 seconds, the picture is advanced or reversed continuously field by field (continuous field advance playback).
3
Press the [PAUSE] button in the Continuous Field
Advance Play mode to restore the Still mode.
Press the [PLAY] button to restore normal playback.
• In the Continuous Field Advance Play mode, no sound is output.
• When continuous field advance playback continues for about 3 minutes, the Stop mode is automatically engaged to protect the tape.
• When forward field-by-field playback is switched to reverse field-by-field playback, noise may appear in the picture for several seconds.
Reverse playback
1
Press the [REVERSE] button in any mode except
Record, Record-Pause or Record Check.
The reverse indicator is shown on the display and the Reverse mode is engaged.
• The tape is played back in reverse in the 3H mode regardless of the playback speed mode setting.
* No sound is output.
2
Press the [PAUSE] button to engage the Still mode.
To restore the normal playback, press the [PLAY] button.
47
7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK
7-3 Special-Effects Playback
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP REC
CHECK OPERATE
EJECT OPERATE
[REW] button
REW
REVERSE
PAUSE PLAY FF
FIELD REV
FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH DISPLAY LOCK CNT RESET
[FF] button
[PLAY] button
Shuttle search (reverse and fast-forward) playback
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T
+
Press the [FF] button or [REW] button in the Play mode to engage the Fast-Forward Shuttle Search mode or Reverse Shuttle
Search mode.
5
Fast-forward shuttle search
Press the [FF] button during play.
The fast-forward search indicator is shown on the display and the Fast-Forward Shuttle
Search mode is engaged.
5
Reverse shuttle search
Press the [REW] button during play.
The rewind search indicator is shown on the display and the Reverse Shuttle Search mode is engaged.
• The operation varies depending on how the [FF] or [REW] button is pressed. Refer to the table below for details.
Type of recording
Operation of the [REW] and [FF] buttons
Press the button once.
Tape recorded in the 3H (SP) mode or the Timelapse mode
9 times 3H (SP) speed (latch).
Press the [PLAY] button to restore the normal play mode
Hold the button pressed for more than 2 seconds.
9 times 3H (SP) speed.
Release the button to restore the normal play mode.
• Latch: Even if the button is released, shuttle search continues.
* During shuttle search, no sound is output.
48
7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP REC
CHECK
OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– +
V. LOCK
– +
TIMER SEARCH DISPLAY LOCK CNT RESET
[REW] button [FF] button
MENU
ON SCREEN
SHIFT
TIME MODE
– S E T +
[SEARCH] button
[SET –] button
EJECT OPERATE
[SET +] button
[SHIFT f] button
7-4 Alarm Search/Date and Time Search
There are three different ways you can search a tape position.
When the [SEARCH] button is pressed, the Search mode is engaged. Each time the [SEARCH] button is pressed, the Search mode changes.
• (Once) alarm search: To search the start of an alarm recording.
(Twice) alarm scan: To play back around the start of each alarm recording for several seconds.
(Three times) date/time search: To search for a recording made at a specified date and time.
Press the [SEARCH] button four times to cancel the Search mode.
Note on date/time search
Recording duration is especially important with timelapse recordings. If the duration is too short, date/time search will not function correctly. The recording duration must be equivalent to at least 5 seconds at Standard (3H) speed.
(Example) In the 240-hour timelapse mode, the recording time should be 7 minutes or more.
Alarm search setting screen
*
*
*
*
*
*
*
*
*
A
0
A
L A
0
L
H
–
R M
0
0
0
5
: S
M
6
0
*
R
1
B
H *
S
L
*
P
0 1 *
*
L
F
–
R
0
*
I
4
Z O O M O N
M A
*
*
D A
D U
*
*
*
*
4
T
R
*
*
E E
E
*
*
*
*
*
*
F I N
*
*
*
*
*
*
*
H
*
*
*
E U
B A
*
*
*
*
*
*
*
*
D E *
*
*
*
*
*
* *
*
A
*
U
* *
*
T
*
O
*
*
*
*
*
*
*
4
*
*
*
*
*
*
T
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
5
*
*
*
*
*
*
*
*
*
*
*
*
Control or reel counter
C R * * T E L
R
N
*
*
*
*
*
E
E
D
*
*
*
*
*
*
*
E
*
*
*
*
*
*
*
*
*
*
*
*
M E N U
*
*
*
*
*
*
*
*
*
*
* A .
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Alarm number
(01- 99)
To specify the alarm recording to be cued, enter the alarm number with respect to the current tape position in the forward or reverse direction.
VCR’s display
Alarm number
Alarm search
A specified alarm recording is searched and the Stop mode is engaged.
1
Press the [SEARCH] button once in the Stop mode.
[ The VCR enters the Alarm Search mode and the alarm search setting screen is shown on the monitor.
The [AL01] indication blinks in the record/playback speed mode indication section on the display.
* To cancel the Alarm Search mode, press the
[SEARCH] button three times.
2
Specify the alarm recording you want to search.
Press the [SET +] or [SET –] button to specify an alarm number from 01 to 99.
The specified alarm number is shown on the monitor and the VCR’s display. The alarm number is not absolute; it depends on the current tape position.
3
Press the [FF] or [REW] button.
[ The VCR fast forwards or rewinds.
When the start of the alarm recording with the specified alarm number is located, search stops and the Stop mode is engaged.
The Alarm Search mode is automatically canceled.
49
7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK
Alarm scan screen
*
*
*
*
4
*
*
*
*
*
A
0
L A
0 H
R
0
M
0
: S
M 0
C
1
A N
S *
0
*
1 *
F R
*
I
*
*
*
*
*
*
*
*
*
*
*
*
*
*
A
*
*
L – 0 5 6 * B L P L – 0 4 * A U T O *
Z Control or reel counter
M
D
A
A
C
T
R
E
D U R E
*
E
*
H
* *
T
E
E
U
L
R
E
E
B A N D
*
*
E
*
*
*
*
*
*
*
*
*
A .
*
T
*
4
*
*
5
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
F
*
*
*
*
*
*
I N
*
*
*
*
*
*
*
*
*
*
*
*
D E
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
M E
*
*
N
*
*
*
*
*
*
*
*
*
U
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Alarm scan
The section around the start of each alarm recording is played back for about 5 seconds.
* Playback may start a few seconds after the actual start of the alarm recording.
* If the interval between alarm recordings is short, the tape may play back continuously for 5 seconds or more.
* Sound is not output.
1
Press the [SEARCH] button twice in the Stop mode.
[ The Alarm Scan mode is engaged and the [ALARM SCAN] indication is shown on the monitor screen. The [ALSC] indication is shown in the display’s record/playback speed mode indication section.
* To release the Alarm Scan mode, press the [SEARCH] button twice.
2
Press the [FF] or [REW] button.
[ The VCR fast-forwards or rewinds the tape from the current position and the section around the start of each alarm recording is played back for about 5 seconds.
3
Press the [PLAY] button when you want to start playback.
[ Normal playback starts and the Alarm Scan mode is canceled.
• To cancel alarm search or alarm scan, press the [STOP] button,
[PLAY] button, [REVERSE] button or the [REW]/[FF] button (whichever is opposite to the current tape running direction).
• When the end or beginning of the tape is reached during alarm search or alarm scan, the mode is canceled and the Stop mode is engaged.
50
Date/time search setting screen
“Day” setting “Time” setting
T
0
*
*
*
*
*
*
*
*
–
*
D
0
–
Z
–
O
–
O
–
M
6
O
–
N
M
D
A
H
S R
0 0
H
M
S
0
*
*
*
*
A
M
U
.
T
*
O
*
*
*
A
*
.
*
D
*
*
*
U
*
*
*
*
*
*
*
*
*
*
*
*
*
*
B
*
*
*
A
*
*
*
N
*
*
*
D
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
4
A
A
*
F
C
*
I
R
E E
*
N
*
*
*
H
*
D
0
1
–
U
T
E
*
E
1
S
D
*
M
E
U
*
*
: –
.
L
R
*
0
*
0 H
–
*
–
*
F R
0
*
E
E
*
M E
*
*
*
*
*
*
N U
*
I
4
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
VCR’s display
“Day” setting “Hour” setting
*
*
*
*
*
*
T
*
*
*
0
1
D
0
0
A
H
–
S
0
1
R
0
0
F
M
6
S
0
1
1
1
5
Z O O M O N U
2
S
D
*
:
M
3
.
0
*
1
*
9 H
F R
–
*
0
*
*
*
*
M
D
A
A
C
T
R
E
D
*
4
U R
*
*
*
*
F
*
*
*
*
I
E
*
*
*
*
N
*
E
*
H
*
*
*
*
*
T
E
E
U
L
R
E
E
*
*
*
*
*
*
*
*
*
B
*
*
*
*
D E
*
*
*
*
*
A N
*
*
D
*
*
*
*
*
*
M E N
*
*
*
E
*
*
*
*
*
*
*
*
U *
*
*
*
*
*
*
I
4
*
*
*
*
T 4
*
*
*
*
*
*
*
*
*
*
*
*
*
A U
*
*
M .
A
*
.
*
*
*
*
*
*
*
*
*
*
*
*
*
T O *
*
*
*
*
*
5
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Set value
19:00 on 12
Search data during tape running
(15:30 on
Oct. 10)
Date/time search
A section recorded at a specified date and time is searched and the
Stop mode is engaged.
1
Press the [SEARCH] button three times in the Stop mode.
[ The Date/Time Search mode is engaged and the date/time search setting screen is shown on the monitor.
“td 0100” is shown on the VCR’s display.
* To cancel the Date/Time Search mode, press the [SEARCH] button once.
2
Press the [SET +] or [SET –] button to set the “date” you want to search (01 - 31).
3
Press the [SHIFT f] button so that “hour” blinks.
4
Press the [SET +/–] button to set the “hour” you want to search (00 - 23).
5
Press the [FF] button or [REW] button.
[ The VCR fast-forwards or rewinds the tape from the current position to search the specified date and time. When the recording is located, the Stop mode is engaged.
The Date/Time Search mode is canceled.
• During date/time search, the month, day, hour and minute which are being searched are shown on-screen.
• If the specified date and time cannot be found and the tape ends, the
Date/Time Search mode is canceled and the Stop mode is engaged.
Notes:
• If the specified date and time is near the start of an alarm recording, the date/time search may not be successful.
• If the specified date/time is the same as the timer-recording start time, the VCR may not operate correctly.
• Date/time search cannot be executed if no date and time are available in the search direction.
7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK
7-5 Repeat Playback
The tape is automatically rewound and played back repeatedly.
• To execute repeat playback, set <REPEAT PLAY> in
<VTR MODE> to “ON”.
VIDEO/VTR MODE screen
2
3
4
*
1
5
6
*
1
2
3
*
.
.
.
.
.
.
*
I
*
N
*
P
*
U
[
T
V
*
I
*
D
*
*
.
.
.
D
V
*
C
*
N
P
E
.
T
P
A
U
O
*
T
W
*
*
E
I
L
*
R
L
S
[
M E
*
*
E
V
M
*
*
O N
A
A
R
R
U
U
E
E
T
T
P
P
O
O
E
E
*
*
A
A
R
R
T
T
E
*
T
*
R
C
E
*
W
P
* R
E
*
*
S
*
*
*
L
*
A
E
O
*
*
*
*
R
C
C
*
*
*
*
M
W *
E
H
*
Y
*
M
*
*
*
O
*
C
E
*
*
*
O
*
*
*
D
*
E
*
*
C
*
*
*
D
*
*
*
*
K
*
*
*
E
*
]
*
*
*
]
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
L
*
I
*
N
*
E
*
*
*
*
*
*
*
*
*
*
O
O
*
O
O
F
F
*
F
F
F
F
*
F
F
O F F
O
O
F
O
F
N
O F F
Set to “ON”.
Auto rewind
When the tape ends during recording, playback, or forward search, the VCR automatically rewinds the tape to the start and enters the Stop mode.
• To auto-rewind the tape, set the <AUTO REW> menu switch in <VTR MODE> to “ON”.
VIDEO/VTR MODE screen
4
5
6
2
3
2
3
*
1
*
1
.
.
.
.
.
.
.
*
.
*
.
*
I
*
N
D E
V .
*
C
*
N
*
P
*
U
[
T
V
*
I
*
D
*
T A
P U
*
T
*
*
I
L
L
S
*
E
*
M
[
E
V
M
*
*
E
*
*
*
O
*
*
*
*
*
*
*
M
*
*
*
O
*
*
*
D
*
*
*
T
*
R
S
*
W
M
*
O
*
D
*
E
*
P
A
O
U
W E
T O
R
*
*
R
O N
E C
*
*
R
C
A U T O
R
R
E
E
P
P
E
E
* R
A
A
T
T
E W *
*
*
P
R
*
L
E
A
C
*
Y
*
E C
H E
*
*
*
*
*
*
* *
C K
*
*
*
*
*
*
*
*
]
*
*
]
*
E
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
L
*
I
* *
N E
O F
O F
F
F
*
*
*
O
*
F
*
F
*
*
*
*
*
*
O
O
F
F
F
F
O O N
O
O
F
F
F
F
Set to “ON”.
Set to “OFF”.
Note:
• When the <REPEAT PLAY> or <REPEAT REC> menu switch is set to “ON”, the tape restarts playback or recording after rewinding to the beginning.
7-6 Counter Memory Function
625
VHS
PAL
VIDEO/VTR MODE
2
3
*
*
1
1
2
3
4
5
6
*
.
*
I
.
D
*
N
*
P
*
U
E T A
[
T
I
V
*
I
*
D
*
*
E O
*
*
*
*
*
*
*
M O D
*
*
*
*
*
* L *
.
.
.
.
.
*
.
V
* *
.
C N
P
A
O
U
P
*
T
U
*
*
W E
T O
L
*
M E M *
R
*
S
[
E
V
*
R
O
E
N
C
A
R
U
E
T
P
O
E
*
A
R
T
E
*
*
T
*
R
W
P
S
*
*
*
L
*
*
W
R
C
*
A
*
M
*
E
H
*
Y
*
O
*
C
E
*
*
*
D
*
*
C
*
*
*
*
*
*
*
E
K
.
R E P E A T * R E C * * * * *
*
*
*
*
*
]
*
*
*
E
* *
]
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
L
*
I
* *
N E
*
*
*
O F F
O
*
F
*
F
*
*
*
*
*
*
O O N
O F
O F
F
F
O
O
F
F
F
F
*
*
O F F
Set to “ON”.
VIDEO CASSETTE RECORDER
SR-S990E
REC
EJECT OPERATE
OPERATE
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL ON SCREEN
MENU
SHIFT
TIME MODE
– S E T
+
[CNT RESET] button
[DISPLAY] button
When the counter memory function is ON, the VCR automatically enters the Stop mode when the control tape counter reaches “00:00:00” or when the reel tape counter reaches “0000” in the FF or REW mode.
5 To activate the counter memory function, set <CNT
MEM SW> in <VTR MODE> to “ON”.
Operation
1
Select the counter display mode.
• Press the [DISPLAY] button on the front panel to set the counter display mode to the control tape counter or reel tape counter.
2
Press the [CNT RESET] button at the position where you want to stop the tape.
[ The counter is set to “00H00M00S” or “0000”.
5 Execute recording or playback.
3
Engage the Stop mode and press the [FF] or [REW] button.
[ When the counter reaches “00H00M00S” or “0000”, the Stop mode is automatically engaged.
Note:
• Repeat record/play, auto rewind and alarm search/ alarm scan/date and time search have priority over the counter memory function.
51
7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP REC
CHECK OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV FIELD ADV
TRACKING
– + –
V. LOCK
+
TIMER SEARCH
DISPLAY LOCK CNT RESET
RESET/
CANCEL
MENU
ON SCREEN
SHIFT
TIME MODE
–
S E T
+
EJECT OPERATE
[V. LOCK +/–] buttons
[TRACKING +/–] buttons
7-7 Tracking/V. Lock Adjustment
When noise appears in the picture in the
Play/Field Advance mode
Tracking adjustment is possible in the following modes.
• 3H (SP) and timelapse play mode (except for L12H and
L24H modes)
• Field advance play
5
Press either the [TRACKING +/–] button until picture noise is eliminated or minimized.
To return to the Tracking Preset mode, press the + and
– buttons simultaneously.
*The tracking adjustment is impossible in the L12H,
L24H Linear Slow play mode.
When a picture moves up and down in the
Still mode and Timelapse Play mode
Press either the [V. LOCK+/–] button to minimize vertical jitter.
7-8 V. PULSE
When the picture is distorted, set the <V. PULSE> menu switch in <VIDEO MODE> to “ON”.
This menu switch is effective only in the 3H mode.
Normally set to “OFF”.
VIDEO/VTR MODE screen
4
5
6
2
3
2
3
*
1
*
1
*
.
.
.
*
.
.
.
.
.
*
I
D
V
*
C
P
.
A
A
R
R
*
N
E T
.
*
N
O
U
U
E
E
*
P
P
*
T
T
T
P
P
*
U
A
*
*
[
T
I
U L
*
M
V
*
L
S
[
E
I
*
*
E
D
*
*
*
V
M
T
*
E
*
*
*
O
*
*
*
*
*
*
*
M
*
*
*
O
*
*
*
R
S
*
W
M O
*
D
*
D
*
*
*
E
*
E
*
]
*
*
*
W E
O
O
E
E
R
*
*
A
A
*
R
R
O
E
T
T
*
*
N
C
*
*
R
C
E W * *
P
R
L
E
A
C
E C * *
H
*
Y
*
E
*
*
*
C
*
*
*
K
*
*
*
*
*
*
*
*
*
*
*
*
*
]
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* *
*
*
L
*
I
*
N
*
E
O F F
*
*
*
*
*
*
*
*
*
O
*
O
O
O
O
O
O
O
*
F
F
F
F
F
F
N
*
F
F
F
F
F
F
Set to “ON”.
• When cameras synchronized with a power supply are switched with a switcher, the pictures may be distorted at the switching point. This switch locks the monitor to prevent distortion of the displayed picture.
(Only operates in the Normal Play [3H] mode)
• In the Still or Timelapse Play mode, V. pulses are always output.
52
8 TROUBLESHOOTING
8-1 Error Indication
Display section
Error indications are shown on the display whenever condensation occurs or there are problems with cassette loading, unloading or mechanism operation.
5
When a problem occurs, the error indication “E-**” lights
(when the <WARNING> menu switch in <F. DISP> is set to “ON”).
5
When any one of error indications (E-01 – E-08) is shown, a 12 V warning signal is output from the rear panel’s WARNING OUT connector.
5 When the <WARNING> menu switch in <BUZZER> is set to
“ON”, the buzzer sounds if a problem occurs (E-01 – E-08 and E-11 (during recording)).
When an error indication appears or the buzzer sounds, turn the operating mode on again to clear the error indication and buzzer sound (E-01 – E-07).
When the error indication “E-**” is shown, turning the operating mode on again may not clear the problem. In this case, consult your local JVC dealer.
Error indication
E-01
E-02
E-03
E-04
E-05
E-06
E-07
E-08
Contents
Problem with loading operation
Problem with unloading operation
Problem with supply reel rotation
Problem with drum rotation
Problem with take-up reel rotation
Problem with capstan rotation
Problem with eject operation
Condensation
E-09
E-10
E-11
Error with recording check
(recording defect)
Insufficient battery capacity for clock and timer backup.
No video signals input.
VCR operation
Error indication
BUZZER screen
*
1
2
3
4
5
6
7
2
3
*
1
.
.
.
*
.
.
*
T
A
*
A
L
*
P
/
*
E
*
*
*
S E N
A U
R
R
T
E
E
P
P
O
E
E
*
A
A
R
T
E
[
E N D
S
.
.
*
.
.
.
W A
* *
C
R
D
T
A
S
U
A
R
*
R
N
*
M
2
E
3
A
P E
I
*
T
*
N
*
R
2
A
C
I
E
G
[
*
*
*
I
*
N
S
B
O N
N D
W
.
*
*
*
*
R
*
/
M
*
O
*
A
*
O
*
U
*
T
*
T
*
E
*
D
*
E
E W
*
*
B
O
P
R
U
*
R
*
L
E
Z Z
*
*
*
A
C
*
I
*
Y
*
E R
*
N
*
*
*
*
*
*
*
*
*
*
]
*
*
*
*
*
*
*
*
]
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
9
*
*
*
*
*
O
*
F
*
F
O F F
O O N
*
O
6
*
F
0
*
F
0
*
*
*
8
*
0
*
*
*
*
S E C
O
O
F
F
F
F
O
O
F
F
F
F
Buzzer sound
Measures
The operating mode is turned off.
The operating mode is turned off.
The operating mode is turned off.
The operating mode is turned off.
The operating mode is turned off.
The operating mode is turned off.
The operating mode is turned off.
The cassette is ejected and the drum starts rotating.
Cassette loading is not possible.
The head cleaner in the VCR cleans the heads.
If a power failure occurs, clock and timer setting data and record/ playback speed settings may be reset.
—
Turn the operating mode on again.
Turn the operating mode on again.
Turn the operating mode on again.
Turn the operating mode on again.
Turn the operating mode on again.
Turn the operating mode on again.
Turn the operating mode on again.
Turn the operating mode on and wait until the error indication goes out.
Clean the heads with a head cleaning tape, then check the recording picture quality again. The tape may be defective. Replace the tape and check again.
If the picture quality is still inferior, contact your local JVC dealer.
Contact your local JVC dealer for replacement of the built-in battery.
Input video signals.
E-12
E-98
E-99
It is not possible to write in
EEPROM.
The tape is broken.
— Contact your local JVC dealer.
E-13
System error
System error
The cassette is ejected. The error indication is shown only while the cassette is being ejected.
The operating mode is turned off.
The operating mode is turned off.
Replace the cassette.
Turn the operating mode on again.
This unit uses a microprocessor and may not function properly if there is external noise or interference. In this case, turn the operating mode off and unplug the power cord from the AC outlet. Then plug the power cord in again and check operation.
53
→
For servicing
See the service manual page 1-6 “1.3.4 Emergency history”.
8 TROUBLESHOOTING
8-2 No Error Indication
Symptoms
No power is supplied.
Operation buttons have no effect during recording and playback.
No picture is shown during playback.
Playback is not possible.
Noise appears in the picture in the Shuttle Search mode, Still mode and Field Advance mode.
Noise appears in part of the playback picture.
Causes
q Is the power cord disconnected?
q Is the [TIMER] indication shown?
q Is the Operation Lock mode engaged?
Is the Operation Lock mode engaged?
q Is the monitor connected correctly?
q Is the [TIMER] indication lit?
Is the [LP] indication blinking on the display?
If it is, it means you are trying to play back the tape recorded in the LP mode.
This is not a malfunction.
Is the tracking adjusted properly?
Remedies
q Connect the power cord to an AC outlet.
q Press the [TIMER] button so that the
[TIMER] indication goes out.
q Release the Operation Lock mode.
Release the Operation Lock mode.
q C o n n e c t t h e m o n i t o r c o r r e c t l y .
q Press the [TIMER] button to clear the
[TIMER] indication.
Tapes recorded in the LP mode cannot be played back on this unit.
—
Adjust the tracking with the [TRACKNG
+/–] button.
Tracking adjustment is not possible in the
L12H and L24H Play modes.
Play back the tape in the 3H mode.
Noise appears in the picture in the L12H or L24H mode.
When the cassette is played back, the picture becomes rough or disappears.
No sound is heard during playback.
Was the tape you are playing back recorded in the L12H or L24H mode? If not, noise appears.
Dust may have accumulated on the video heads.
During playback, sound is highpitched and hard to hear.
Recording is impossible.
Timer recording is not working.
The clock cannot be set.
Tape running sound is heard in the Record, Play, FF and REW modes.
The time/date is not shown.
Auto REW and repeat recording are not possible during recording.
Camera image is not switched.
External recording is not possible.
q Are you recording in a timelapse mode (except L12H and L24H)? If so, sound is not recorded.
q During alarm scan, no sound is output.
Are you playing back a tape recorded in the L12H, or L24H
Timelapse mode in the 3H (SP) mode? In this case, sound is highpitched.
Has the cassette safety tab been removed?
q Is the clock set correctly? Is the timer properly programmed?
q Is the [TIMER] indication lit?
Is the [TIMER] indication lit?
During recording and playback, the
VCR’s motor and rotary heads are running. The sound this generates is normal and not a malfunction.
q Is the clock set?
q Is the <ON SCREEN MODE> menu switch set to “OFF”?
Is the <TAPE END MODE> menu switch in <ALARM/SENSOR
MODE> set to “STOP”?
Is the <CAMERA SW> menu switch in <IN/OUT> set to “OFF”?
Is the <REPEAT REC> menu switch in the <VTR MODE> menu set to
“ON”?
54
Clean the heads with a commerciallyavailable head cleaning tape. If the picture quality is still unsatisfactory, consult your local JVC dealer.
Use a tape on which sound is recorded.
(Record the tape in the L12H or L24H mode.)
Play back the tape in the same mode
(L12H or L24H) as that used for recording.
Paste a piece of cellophane tape over the hole.
q Check again.
q Check it again.
Press the [TIMER] button so that the
[TIMER] indication goes out.
If you feel it is too noisy, install the VCR in a rack.
q Set the clock.
q Set the <ON SCREEN MODE> menu switch to “ON”.
Set the <TAPE END MODE> menu switch to “OFF”.
When setting the camera switching timing on this unit, set the menu switch to “1 FIELD” or
“2 FIELD”.
To perform repeat recording using external recording activation, set <REPEAT REC> to “OFF” and <AUTO REW> to “ON”.
9 OPTIONAL SA-K97U RS-232C INTERFACE BOARD
Functions that can be controlled with front panel buttons and switches can also be controlled from a personal computer when the optional SA-K97U RS-232C interface board is installed. Operation status can also be monitored on the computer.
9-1 Installation of the SA-K97U
Screws
4.
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
VIDEO
Y/C
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
COM
ALARM
IN
ALARM
REC OUT
ALARM
RESET
TAPE
COM
END OUT
CLOCK
RESET IN
WARNING
OUT
SERIES
RESET IN
CLOCK
RESET OUT
SERIES
RESET OUT
SA-K97U installation section
1.
Top cover
2.
Plate
Rear panel
3.
SA-K97U
Screws
Wire (not used)
The procedure is shown below. However, to avoid electric shock or injury, contact your local JVC service center for details.
Note:
To avoid electric shock, be sure to unplug the power cord from the AC outlet before installing the SA-K97U.
1. Detach the top cover.
Note:
Be careful when removing the top cover. The edges of the cover could injure you if handled improperly.
Remove the 4 screws securing the top cover and lift it off.
2. Detach the plate in the VCR.
Remove the 2 screws on the rear panel. Detach the plate from the inside of the VCR.
3. Detach the SA-K97U’s wire.
* The SA-K97U’s wire is not used.
4. Install the SA-K97U in the VCR.
Hold the board as shown in the illustration and secure it using the screws removed previously in step 2.
5. Connect the VCR’s wire to the SA-K97U’s connector.
• Check the direction of the connector and connect it.
• Press both ends of the connector to firmly connect it.
6. Replace the top cover on the VCR and secure it with the four screws previously removed in step 1.
Connector
5.
Wire
SA-K97U
R S - 2 3 2 C
REMOTE
MIC
AUDIO
IN
OUT
VIDEO
Y/C
AC~IN
AC220-240V~50/60Hz
CAM SW
OUT
COM
ALARM
IN
ALARM
REC OUT
ALARM
RESET
COM CLOCK
RESET IN
TAPE
END OUT
WARNING
OUT
SERIES
RESET IN
CLOCK
RESET OUT
SERIES
RESET OUT
55
9 OPTIONAL SA-K97U RS-232C INTERFACE BOARD
9-2 SA-K97U Specifications
9-pin connector specifications
Pin NO.
4
5
2
3
6
Signals
RXD
TXD
DTR
GND
DSR
Operations
Receive data
Transmit data
Data terminal ready
Signal ground
Data set ready
Direction of signals
VTR p CPU
VTR [ CPU
VTR [ CPU
VTR p CPU
Output level
ON : +5 V or more
OFF : –5 V or less
Data format
5
Mode :
Non-synchronized
5
Character length :
8 bits
5
Data rate :
600,1200, 2400, 4800, 9600 bps
(switched with on-screen menu switch, set to 9600 bps before shipment)
5
Parity check
5
Stop bit
:
No
:
1 bit
6
9
Configuration
0 (SPACE)
1 (MARX)
Start bit D0 D1 D2 D3 D4 D5 D6 D7 Stop bit
1
2
3
4
5
9 OPTIONAL SA-K97U RS-232C INTERFACE BOARD
9-3 SA-K97U RS-232C Protocol & Commands
RS-232C protocol
This VCR is provided with JVC basic table commands in addition to the JVC table-1 commands shown below.
The commands in the shaded area in the table below are contained in both the JVC table-1 and JVC basic table. The JVC basic table commands include only those in the shaded areas.
JVC table-1
0
0
1 2
E
F
A
B
C
D
1 COMPLE-
TION
2 ERROR
3 CASSETTE
OUT
4
8
9
5
6
NOT
TARGET
ALARM
INPUT
7
ACK
NAK
3 4
Data “0” ENTER
Data “1” CLEAR
ERROR
Data “2”
Data “3”
Data “4”
Data “5”
Data “6”
Data “7”
Data “8”
Data “9”
PLAY REV
PLAY
STOP STILL
5
CLEAR
6
TIMER
ON
TIMER
OFF
7
ON SCREEN
ON
ON SCREEN
OFF
PRG/CLK ROM VER
SHFT+
SHFT–
POS V+
ON SCREEN
SELECT
POS H+ SET+
SET–
8
TL STATUS
SET
CANCEL
9 A B
VISS
FWD
C
VISS REC
REV CHECK
D
FRAME CODE
(COUNT)
DEVICE
TYPE
E
AL . PL
RESET
HOUR METER COUNT
SENSE RESET
EJECT SEARCH
(VISS)
PL .AL COUNT
SENSE
TL STATUS
SENSE
STATUS
SENSE
F
JVC
TABLE1 ON
JVC
TABLE1 OFF
OPE LOCK
ON
OPE LOCK
OFF
OPERATE ON
OPERATE OFF
MODE
SHIFT
MODE DATE SET
TIME SET
REC
FF
REW
F-FIELD
STEP
R-FIELD DATE
STEP SENSE
TIME
SENSE
REC
PAUSE
REC
REQUEST
VTR INQ
56 57
9 OPTIONAL SA-K97U RS-232C INTERFACE BOARD
9-3 SA-K97U RS-232C Protocol & Commands
This section provides technical data for programmers.
Command description
To use the commands described in the following pages, prepare the VCR for communications as follows:
Transmit the command “JVC TABLE 1 ON” (F6H) to the VCR. The VCR will return “ACK” (0AH). When the operating mode is turned on, the VCR is in the “ON” status.
The VCR can now receive any command described in this section. To cancel the communications mode, transmit the command “JVC
TABLE 1 OFF” (F7H).
1 VCR control commands
Commands (1) through (12) are 1-byte commands. The VCR will return “ACK” (0AH) when the command is received. Confirm that “ACK”
(0AH) has been returned before transmitting the next command.
(1) OPERATE ON (7BH)
OPERATE OFF (7CH)
(2) PLAY (3AH)
(3) STILL (4FH)
(4) STOP (3FH)
(5) FF (ABH)
(6) REW (ACH)
(7) REV PLAY (4AH)
(8) TIMER ON (60H)
TIMER OFF (61H)
(9) OPE LOCK ON (69H)
OPE LOCK OFF (6AH)
(10) EJECT (A3H)
(11) F-FIELD STEP (ADH)
(12) R-FIELD STEP (AEH)
(13) REC CHECK (C1H)
: VCR operating mode is turned “ON”.
: VCR operating mode is turned “OFF”.
: Playback
: Pause/Still
: Stop
: FF/Forward search in the Play mode.
: REW/Reverse search in the Play mode.
: Reverse playback at normal speed
: Timer “ON”
: Timer “OFF”
: Operation lock “ON”
: Operation lock “OFF”
: Cassette ejection
VCR returns “ACK”, and then returns CASSETTE OUT (03H) after cassette has been ejected.
: Advances the tape by one field when the VCR is in the Still mode and engages the Still mode.
If the VCR is in any other play mode, the Still mode is engaged.
: Reverses the tape by one field when the VCR is in the Still mode and engages the Still mode.
If the VCR is in any other play mode, the Still mode is engaged.
: Engages REC CHECK. (function is the same as when locally controlled on the VCR.)
Before transmitting either of the following commands ((14) or (15)), first transmit REC/DUB REQUEST (FAH), and confirm that “ACK” (0AH) is returned by the VCR.
(14) REC (CAH)
(15) REC PAUSE (CBH)
: Starts recording. The VCR returns “ACK” (0AH).
If the cassette tape’s safety tab [REC TAB] has been removed, NAC (0BH) is returned.
• When REC PAUSE (FAH+CBH) is sent in the Record mode, the Record-Pause mode is engaged.
• When STOP (3FH) is sent in the Record mode, the Stop mode is engaged.
: Engages Record-Pause mode. The VCR returns “ACK” (0AH).
If the cassette tape’s safety tab has been removed, NAC (0BH) is returned.
• To re-start recording, transmit REC (FAH+CAH).
• To cancel Record-Pause, transmit STOP (3FH). The VCR will enter the Stop mode.
After transmitting commands VISS FWD (16) or VISS REV (17), transmit the appropriate numeric data (1-byte ASCII codes from 30H to 39H) and the data input command (40H).
ASCII codes “30H – 39H” correspond with the numbers “0 – 9” (ie.: 0: 30H, 1: 31H, ... 9: 39H).
Each byte of numeric data and the data input command should be transmitted separately with “ACK” (0AH) confirmation from the VCR after each transmission. * Transmit the commands (16) and (17) in the Stop mode.
(16) VISS FWD (B0H)
(17) VISS REV (B1H)
: To advance the tape in the forward search mode to the designated alarm-input point. The alarm point’s 2-byte numeric data should be input after transmission of this command.
: To reverse the tape in the reverse search mode to the designated alarm-input point. The alarm point’s 2-byte numeric data should be input after transmission of this command.
Eg: To search for the 3rd alarm-input point from the current position.
TXD
RXD
B0H
0AH
30H
0AH
33H
0AH
40H
0AH
Search start
01H (or 05H)
Time
The VCR starts search after returning “ACK”. When the specified point is reached, the VCR returns COMPLETION (01H). If the end or beginning of the tape is reached before the specified point, the VCR returns NOT TARGET (05H). (Sending either the 30H, 30H or 30H,
31H command will cause the VCR to search for the 1st alarm-input point).
58
9 OPTIONAL SA-K97U RS-232C INTERFACE BOARD
After transmitting the VISS SEARCH command (18), transmit the appropriate 2-byte numeric data (from 30H to 39H), the data input command
(40H), and either FF (ABH) or REW (ACH). All commands should be transmitted separately one byte at a time with “ACK” (0AH) confirmation from the VCR after each transmission. * Execute in the Stop mode.
(18) VISS SEARCH (B3H) : To search for a designated alarm-input point on the tape.
The VCR starts search after returning “ACK”. When the specified point is reached, the VCR returns COMPLETION (01H). If the end or beginning of the tape is reached before the specified point, the VCR returns NOT TARGET (05H).
This command differs from commands (16) and (17) only in that the FF (ABH) or REW (ACH) command is included separately.
2 VCR setting commands
Commands available include control of recording/playback mode setting, timelapse VCR operation mode setting, date and time setting, timer programming, on-screen setting, and others.
5 Recording/playback mode setting commands
Two commands are available. One allows you to rotate through recording/playback modes, the other permits you to directly select the mode.
(1) MODE SHIFT (7DH) : Switches from one recording/playback mode to the next each time the command is transmitted. Use the TL
STATUS SENSE (D6H) command to check the current mode.
Transmit 1 byte at a time with “ACK” (0AH) confirmation from the VCR after each transmission.
(2) MODE (7EH) : Sets recording/playback mode directly.
After transmitting this command, transmit the appropriate 2-byte ASCII codes (from 30H to 39H) and the data input command (40H). Correspondence of ASCII codes with recording/playback modes is as shown below.
Eg: To set to “L24H”.
TXD
RXD
7EH
0AH
30H
0AH
33H
0AH
40H
0AH
Time
Mode
3H
L12H
L24H
24H
48H
72H
120H
168H
240H
1st byte 2nd byte
30H
30H
30H
30H
32H
33H
31H
30H
30H
36H
34H
35H
30H
30H
30H
37H
38H
39H
5 Timelapse VCR operation mode setting commands
(1) TL STATUS SET (86H) : Set the timelapse VCR operation mode with 3-byte data. Send one byte at a time by checking
ACK (0AH) from the VCR.
TXD
RXD
86H
0AH
1st byte
0AH
2nd byte
0AH
3rd byte
• The setting details for the first to the third bytes are shown below.
0AH
Time
1st byte
BIT
6
7
4
5
2
3
0
1
3rd byte
BIT
6
7
4
5
2
3
0
1
When the bit is “1”
Repeat recording function ON
Unused
POWER ON REC mode ON
Auto rewind ON
Unused
Series recording function ON
Tape end buzzer ON during recording
Alarm recording buzzer ON
When the bit is “1”
Unused
Summer time compensation ON
Unused
Unused
Unused
Auto record check function ON
Unused
Unused
2nd byte
BIT
6
7
4
5
2
3
0
1
When the bit is “1”
Unused
Alarm recording function ON
Unused
Sensor recording function ON
External recording function ON
Unused
Unused
Warning buzzer ON
59
9 OPTIONAL SA-K97U RS-232C INTERFACE BOARD
5 Date and time setting commands
(1) DATE SET (8EH) : Set the current date (month, day, year) for the VCR. After this command (8EH) is sent, input 1byte numerical data (30H — 39H).
(Example) March, 30, 1999
TXD
RXD
8EH
0AH
30H
0AH
33H
0AH
33H
0AH
30H
0AH
39H
0AH
39H
0AH
Time
Month
Day Year
(2) TIME SET (8FH) : Set the current time (hour, minute, second) for the VCR.
After this command (8FH) is sent, input 1-byte numerical data (30H — 39H).
(Example) 15 hours, 29 minutes, 59 seconds
TXD
RXD
8FH
0AH
31H
0AH
35H
0AH
32H
0AH
39H
0AH
35H
0AH
39H
0AH
Time
Hour Minute Second
5 Timer programming commands
(1) PRG/CLK (62H)
(2) SHIFT – (64H)
SHIFT + (63H)
(3) SET – (66H)
SET + (65H)
(4) CANCEL (67H)
: Engages timer programming mode.
: Selects setting items. (–)
: Selects setting items. (+)
: Sets data selected with SHIFT.
: Sets data selected with SHIFT.
: Cancels program data in timer programming or engages the Cancel Program mode.
Setting procedure is the same as when using the VCR controls. Be sure to transmit commands 1 byte at a time with “ACK” (0AH) confirmation from the VCR after each transmission.
5 On-screen setting commands
(1) ON SCREEN ON (70H)
ON SCREEN OFF (71H)
: Activates on-screen indication.
: Deactivates on-screen indication.
Setting procedure for the following command (2) is the same as when using the VCR controls. Be sure to transmit commands 1 byte at a time with “ACK” (0AH) confirmation from the VCR after each transmission.
(2) ON SCREEN SELECT (74H): Switches the on-screen display items.
POS V+ (73H): Moves the on-screen indication in the vertical direction.
POS H+ (75H): Moves the on-screen indication in the horizontal direction.
5 Other commands
(1) AL/PL RESET (E1H)
(2) COUNT RESET (E2H)
: When transmitted during alarm recording, the recording mode switches back to the previous mode.
The VCR’s “AL” indication goes off. Transmit again after “AL” indicator goes off to reset the alarm/ power loss memory.
: Resets the tape counter to “0000”.
9 OPTIONAL SA-K97U RS-232C INTERFACE BOARD
3 Commands for VCR status verification
When the command is sent, the VCR returns the corresponding information.
(1)
(2)
DATE SENSE (BEH)
TIME SENSE (BFH)
: The VCR returns the currently set month, day and year as 6 bytes. Each byte has a value of 30H to
39H. 30H corresponds to 0 and 39H to 9.
(Example: For March, 14, 1999, the VCR returns 30H, 33H, 31H, 34H, 39H and 39H.)
: The VCR returns the currently set hour, minute and second as 6 bytes. Each byte has a value of
30H to 39H. 30H corresponds to 0 and 39H to 9.
(Example: For 15:30:45, the VCR returns 31H, 35H, 33H, 30H, 34H and 35H.)
(3) COUNT CODE (D0H)
(4) DEVICE TYPE (D1H)
: VCR returns the counter data beginning with the 4th digit from the right in 4 bytes. ASCII codes
“30H – 39H” correspond with the numbers “0 – 9” (eg: 1234: 31H, 32H, 33H, 34H).
: VCR returns the last 4 characters of the SR-S990 model name in ASCII code.
(5) VTR INQ (FBH)
53H, 39H, 39H, 30H
: Used to make sure that the connected unit is the VCR. The VCR will return “ACK” (0AH).
(6) PL/AL COUNT SENSE (D5H) : VCR will return a total of 6 bytes. The first 3 bytes show the number of alarm inputs in 3 digits and the last 3 bytes show the number of power losses in 3 digits. ASCII codes “30H – 39H” correspond with the numbers “0 – 9” (eg: 123 alarm inputs and 45 power losses: 31H, 32H, 33H, 30H 34H,
35H).
(7) HOUR METER SENSE (D2H) : VCR returns the hour meter data in 4 bytes. (eg: 1234 hours: 31H, 32H, 33H, 34H).
(8) TL STATUS SENSE (D6H) : VCR returns Timelapse mode data in 6 bytes. The contents of each byte are as follows:
1st/2nd byte
Recording/playback mode
Correspondence of the code and the mode is the same as MODE (7EH) (see page 59).
3rd byte
Conditions of each setting
3
4
5
6
7
1
2
BIT
0
Status when BIT is “1”.
Repeat Record mode ON.
Power is ON.
POWER ON REC mode is ON.
Auto rewind mode is ON.
Operation lock is ON.
*
Series recording is ON.
Tape end buzzer is ON.
Alarm buzzer is ON.
5th byte
Settings status
3
4
5
6
7
1
2
BIT
0
Status when BIT is “1”.
Always 1.
SUMMER TIME is ON.
S-VHS mode is ON.
Y/C input is ON.
Always 0
Auto record check function ON.
Always 0.
Always 0.
4th byte
Conditions of each setting
3
4
5
6
7
1
2
BIT
0
Status when BIT is “1”.
Alarm recording is in progress.
ALARM REC function is ON.
Not defined. Always 0.
Sensor recording is ON.
External recording function is ON.
V.pulse is ON.
Always 0.
Warning buzzer is ON.
6th byte
Types of warnings
HEX.Data
Types of warnings
0 No abnormality
1
2
Loading error
Unloading error
3
4
5
Supply reel error
Drum error
Take-up reel error
6
7
8
9
A
B
Capstan error
Cassette eject error
DEW sensor error
Recording check error
Battery backup error
Input signal error
*
Operation with commands from the RS-232C is accepted even in the Operation Lock mode.
60 61
9 OPTIONAL SA-K97U RS-232C INTERFACE BOARD
(9) STATUS SENSE (D7H) : The VCR will return current status information in 5 bytes.
1st byte
BIT
0 Error
1 Not defined
2 Not defined
3 Cassette out
4 REC inhibit
5 Not defined
6 Not defined
7 Not defined
2nd byte
BIT
0 Tape End
1 Tape Begin
2 Not defined
3 Warning
4 Not defined
5 Not defined
6 A EE Mode
7 V EE Mode
3rd byte
BIT
0 Not defined
1 Search Mode
2 Repeat Mode
3 Not defined
4 Repeat
5 Counter
6 Timer REC ON
7 Not defined
Status when BIT is “1”.
Indicates that an illegal command has been received. No further commands will be accepted.
To restore to normal operation, transmit CLEAR ERROR (41H) to the VCR.
Always 0.
Always 0.
The tape has not been loaded.
A tape with no safety tab has been loaded. In this case, no recording commands will be accepted.
Always 0.
Always 0.
Always 1.
Status when BIT is “1”.
Tape end sensor is detected.
Tape begin sensor is detected.
Always 0.
VCR malfunction.
*
Always 0.
Always 0.
An externally-input audio signal is being output.
An externally-input video signal is being output.
Status when BIT is “1”.
Always 0.
Search is in progress. (VISS)
Repeat recording is in progress.
Always 0.
VCR’s REPEAT REC menu switch is set to ON.
Counter memory is set to ON.
VCR’s TIMER button is set to ON.
Always 0.
4th byte
BIT
0 Not defined
1 REC Mode
2 Eject
3 Not defined
4 Stop Mode
5 REW Mode
6 FF Mode
7 PB Mode
5th byte
BIT
0 Speed Code 0
1 Speed Code 1
2 Speed Code 2
3 Speed Code 3
4 Shuttle REV
5 Shuttle FWD
6 Not defined
7 Rec-Pause Mode
Status when BIT is “1”.
Always 0.
VCR is in the Record mode.
A cassette is being ejected.
Always 1.
VCR is in the Stop mode.
VCR is in the Rewind mode.
VCR is in the Fast-Forward mode.
VCR is in the Play mode.
Status when BIT is “1”.
VCR’s current tape running mode. See below.
VCR’s current tape running mode. See below.
VCR’s current tape running mode. See below.
VCR’s current tape running mode. See below.
Reverse search is in progress.
Forward search is in progress.
Always 0.
VCR is in the Pause mode.
Contents of 5th byte BIT 0/1/2/3 “Speed Code”
Speed Code 3 2 1 0
BIT 0 0 0 0 Still
0 0 0 1 Timelapse playback
0 1 0 1 Timelapse recording/3H (SP) playback
1 0 0 0 Search (X9)
*
When an error occurs in the VCR and the Warning mode is engaged, the third bit of the second byte sent back with the STATUS
SENSE (D7H) is set to “1”, showing the warning status.
In this case, release the warning via the RS-232C with the CLEAR (56H). To release it on the VCR, turn the [OPERATE] button off and on again.
(10) ALARM INPUT (06H) : SR-S990E/EK return code
This is returned when an alarm signal is input during recording.
62
9 OPTIONAL SA-K97U RS-232C INTERFACE BOARD
4 Others (Input data correction/Error cancellation)
These are return codes from the SR-S990E/EK. (Error-related codes only)
(1) ERROR (02H) : This is returned when commands of more than 1 byte are transmitted to the VCR and an illegal command is received in the 2nd byte (or later) of the transmitted command.
In this status, no command can be accepted and only STATUS SENSE will be returned.
To restore normal operation, transmit CLEAR ERROR (41H) or CLEAR (56H) to the VCR.
CLEAR ERROR (41H) : Used to cancel previously-transmitted 1-byte numeric data when inputting numeric data such as search point. Also used to cancel error status.
CLEAR (56H) : Clears the whole command. Cancels the current status and stops the VCR. Also cancels the error status.
Eg : After setting the recording/playback mode to “L24H”, 32H is mistakenly transmitted . Cancel 32H with
“41H” and input “33H” instead.
TXD
7EH
RXD
0AH
30H
0AH
32H
0AH
41H
0AH
33H
0AH
40H
0AH
Time
(2) NAK (0BH) : VCR will return this code when non-defined or non-functional command is received in the 1st byte of the transmitted command. In this case, it is not necessary to input CLEAR. Check whether the transmitted command is acceptable to the VCR or not.
5 Commands reference chart
VCR control commands
OPERATE ON/OFF
PLAY/REV PLAY
STOP
FF/REW
TIMER ON/OFF
OPE ON/OFF
EJECT
F-FIELD STEP
R-FIELD STEP
REC CHECK
REC/REC PAUSE
VISS FWD/REV
VISS SEARCH
Commands for VCR status verification
Page
COUNT CODE
DEVICE TYPE
VTR INQ
PL/AL COUNT SENSE
HOUR METER SENSE
TL STATUS SENSE
STATUS SENSE
DATA SENSE
TIME SENSE
51
51
51
51
51
51
52
51
51
Byte returned from VCR
4 bytes
4 bytes
1 byte
6 bytes
4 bytes
6 bytes
5 bytes
6 bytes
6 bytes
Page
58
58
58
58
58
58
58
58
58
58
58
58
59
VCR setting commands
5 Recording/playback mode
MODE SHIFT
MODE
5 Timelapse VCR operation mode
TL STATUS
5 Date and time setting
DATE SET
TIME SET
5 Timer programming
PRG
SHIFT –/+
SET –/+
CANCEL
5 On-screen setting
ON SCREEN ON/OFF
ON SCREEN SELECT
POS V+
POS H+
5 Others
AL/PL RESET
COUNT RESET
Return codes from VCR
ACK
NAK
ERROR
CASSETTE OUT
COMPLETION
NOT TARGET
ALARM INPUT
Others
JVC TABLE 1 ON/OFF
Page
58
63
63
58
58
58
62
Page
59
59
59
60
60
60
60
60
59
59
60
60
60
60
60
60
60
60
60
60
60
Page
58
63
10 APPENDIXES
10-1 Tape Reel Counter/Tape Remaining Time Table
The table below shows the tape remaining time with the tape reel counter value in each record/playback speed mode (when a E-
180 tape is used).
Since actual tape remaining time may differ from the values in the table below, use these values for reference only.
When a E-180 tape is used: Tape remaining time when the tape reel counter is “0000” at the beginning of the tape.
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
5600
5700
5800
5900
6000
6018
53 m
40 m
28 m
17 m
8 m
6 m
4 m
3 m
1 m
0 m
0 m
3H
3 h 3 m
2 h 41 m
2 h 19 m
2 h 0 m
1 h 41 m
1 h 24 m
1 h 8 m
L12H
12 h 15 m
10 h 44 m
9 h 19 m
8 h 0 m
6 h 45 m
5 h 36 m
4 h 32 m
3 h 33 m
2 h 40 m
1 h 52 m
1 h 10 m
33 m
25 m
19 m
12 m
6 m
0 m
0 m
Record/playback speed modes
L24H
24 h 30 m
21 h 29 m
18 h 39 m
16 h 0 m
13 h 31 m
11 h 12 m
9 h 5 m
7 h 7 m
5 h 21 m
3 h 45 m
2 h 20 m
1 h 6 m
51 m
38 m
25 m
13 m
1 m
0 m
48H
49 h 1 m
42 h 59 m
37 h 19 m
32 h 0 m
27 h 2 m
22 h 25 m
18 h 10 m
14 h 15 m
10 h 43 m
7 h 31 m
4 h 41 m
2 h 12 m
1 h 43 m
1 h 17 m
51 m
27 m
3 m
0 m
72H
73 h 32 m
64 h 29 m
55 h 58 m
48 h 0 m
40 h 33 m
33 h 38 m
27 h 15 m
21 h 23 m
16 h 4 m
11 h 17 m
7 h 1 m
3 h 18 m
2 h 35 m
1 h 56 m
1 h 17 m
40 m
4 m
0 m
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
5600
5700
5800
5900
6000
6018
120H
122 h 33 m
107 h 29 m
93 h 18 m
80 h 0 m
67 h 35 m
56 h 3 m
45 h 25 m
35 h 39 m
26 h 47 m
18 h 48 m
11 h 42 m
5 h 30 m
4 h 19 m
3 h 13 m
2 h 9 m
1 h 7 m
7 m
0 m
Record/playback speed modes
168H
171 h 34 m
150 h 28 m
130 h 37 m
112 h 0 m
94 h 37 m
78 h 28 m
63 h 35 m
49 h 55 m
37 h 30 m
26 h 19 m
16 h 23 m
7 h 42 m
6 h 3 m
4 h 30 m
3 h 1 m
1 h 3 m
11 m
0 m
240H
245 h 7 m
214 h 58 m
186 h 36 m
160 h 0 m
135 h 10 m
112 h 7 m
90 h 50 m
71 h 19 m
53 h 35 m
37 h 37 m
23 h 25 m
11 h 0 m
8 h 38 m
6 h 26 m
4 h 18 m
2 h 15 m
15 m
0 m
• When the cassette tape is ejected, the tape reel counter is reset to “0000”.
• When the tape is rewound to the beginning in the Repeat Recording or Auto Rewind mode using the counter end output function, the tape reel counter is reset to “0000”.
Counter end output function: Set the menu switch <CNT TAPE END> to any position except “OFF”.
64
10 APPENDIXES
10-2 Rear Panel’s Input/Output
Terminals
CAM SW OUT
Camera switching signal output
Signal levels
During recording
During standby
GND
1 field
5 ms
(Timelapse recording)
Camera switching signal output Time
The switching interval can be set to“1 field” or “1 frame”with the
<CAMERA SW> in the
<IN/OUT> setting screen.
(With the menu switch set to “1 field”)
HV: 5 V
ALARM IN
Alarm signal input
LV: 0 V
ALARM RST IN
Alarm signal reset input
HV: 5 V ~ 12 V
ALARM REC OUT
Alarm recording mode signal output
TAPE END OUT
Tape end signal output
Min. 400 ms
HV:12 V
(output impedance: 4.7 kohms)
About 2 s
Alarm
Record mode
Record mode: repeat recording ON/auto rewind ON
HV: 12 V
LV: 0 V
Max. 10 mA
Record mode: repeat recording OFF/auto rewind OFF
Tape end
Manual operation
WARNING OUT
Warning signal output
Warning
Min. 400 ms
HV: 12 V
(output impedance: 4.7 kohms)
Warning reset
HV: 5 V
CLOCK RESET IN
Clock reset input
About 100 ms
LV: 0 V
CLOCK RESET
OUT
Clock reset output
About 100 ms
LV: 0 V
HV: 5 V
Remarks
Open-collector output
Input at ground level
Input at high level
Output at high level
Output at ground level
Output at high level
Input at ground level
Output at ground level
SERIES REC IN
Series recording signal input
2.5 - 3 s
LV: 0 V
Input at ground level
HV: 5 V
SERIES REC OUT
Series recording signal output
2.5 - 3 s
LV: 0 V
Output at ground level
HV: 5 V
SERIES REC IN
External automatic recording signal input
External recording
Min. 400 ms
Input at ground level
65
10 APPENDIXES
10-3 Specifications
5
5
Recording system
Signal system
Luminance: FM recording
Colour: down-converted direct recording
PAL-type colour signal, CCIR monochrome signal, 625 lines/
50 fields
23.39 mm/s, Standard mode (3H) 5
Tape speed
5
Recording and playback time
(with E-180 cassette)
3 hours (Standard (3H) mode)
L12, L24, 24, 48, 72, 120, 168,
240 hours
However, L12/L24 can only be selected when an S-VHS tape is used.
5
Fast-forward/ rewind time
5
Power supply
(Timelapse mode: field recording)
Within about 4 min
(with E-180 cassette)
5
Power consumption
5
Dimensions
AC 220 V-240 V, 50/60 Hz
19 watts
(W) 360 mm x (H) 115 mm x (D)
370 mm
5
Weight
Approx. 5.5 kg
5
Operating temperature
5°C to 40°C
5
Operating humidity
30%RH or more, 80%RH or less
5
Storage temperature
–20°C to 60°C
[Video System]
5
Signal input LINE
Y/C
5
Signal output LINE
Y/C
1.0 V(p-p), 75
Ω, unbalanced BNC
Y: 1.0 V(p-p), 75
Ω, unbalanced
C: 0.3 V(p-p), 75
Ω, unbalanced
(Burst)
1.0 V(p-p), 75
Ω, unbalanced BNC
Y: 1.0 V(p-p), 75
Ω, unbalanced
C: 0.3 V(p-p), 75
Ω, unbalanced
(Burst)
5
Horizontal resolution
400 lines or more
(S-VHS: 3H mode)
5
Video S/N
43 dB or more (S-VHS: 3H mode)
[Audio system]
5
Number of tracks
5
Line input
5
Mic input
5
Line output
5
Frequency response
5
Audio S/N
5
Wow and flutter
1 (normal)
–8 dBs, 50 k
Ω, unbalanced RCA
–67 dBs, 600
Ω, unbalanced
–8 dBs, 1 k
Ω, unbalanced RCA
100 Hz to 10 kHz (3H mode)
40 dB or more (3H mode at 4% distortion level)
0.30% WRMS or less (3H mode)
[Time/date]
5
Display
5
Display position
5
Character size
5
Power backup
Day, month, year, hours, minutes, seconds, recording mode, alarm input data, power loss data
Variable
16H
Approx. two years (may be less depending on the operating environment)
[Alarm]
5
Alarm input
5
Camera switching output
5
Accessory
Input at ground level
Negative pulse output (5 ms)
Open-collector output
Power cord x 1
Outer dimensions
360
VIDEO CASSETTE RECORDER
SR-S990E
REC
625
VHS
PAL
REC STOP REC
CHECK OPERATE
REW REVERSE PAUSE PLAY FF
FIELD REV
FIELD ADV
TRACKING
– +
V. LOCK
– +
TIMER SEARCH DISPLAY LOCK CNT RESET
RESET/
CANCEL
MENU
ON SCREEN
SHIFT
TIME MODE
S E T
EJECT OPERATE
Unit: mm
* Design and specifications subject to change without notice.
66 67
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- - 1-1 Major Features
- - 1-2 Periodical Maintenance
- - 1-3 Daily Inspection
- - 1-4 Precautions
- - 1-5 Regarding S-VHS ET Recording
- - 2-1 Front Panel
- - 2-2 Display
- - 2-3 Rear Panel
- - 3-1 Connecting to a Camera
- - 3-2 System Using Sequential Switcher
- - Terminal Connections
- - 4-1 On-Screen Display
- - 4-2 Main Menu Display
- - 4-3 Date and Time Setting
- - 4-4 Hour Meter Display
- - 4-5 Alarm Input/Power Loss Data Display
- - 4-6 Menu Switch Setting
- 1 4-7 Contents of Menu Switches
- 5 5-1 Cassette Loading/Unloading
- 6 Selection
- 7 6-1 Switch Setting During Recording
- 8 6-2 Recording Basic Operation
- 9 6-3 Timer Recording
- 9 • Timer Recording Program Setting
- 13 • Holiday Timer Recording Setting
- 14 Program
- 15 • Notes on Timer Recording
- 16 6-4 Alarm Recording
- 18 6-5 Sensor Recording
- 19 6-6 Series Recording
- 21 6-7 Repeat Recording
- 22 Signal
- 23 Failure
- 23 6-10 External Timer Recording
- 23 6-11 Tape End Buzzer
- 24 7-1 Preparation
- 24 7-2 Playback
- 25 7-3 Special-Effects Playback
- 25 • Still/Field advance/reverse playback
- 26 • Shuttle search playback
- 27 7-4 Alarm Search/Date and Time Search
- 29 7-5 Repeat Playback
- 29 7-6 Counter Memory Function
- 30 7-7 Tracking/V. Lock Adjustment
- 30 7-8 V. Pulse
- 31 8-1 Error Indication
- 32 8-2 No Error Indication
- 33 9-1 Installation of the SA-K97U
- 34 9-2 SA-K97U Specifications
- 29 Commands
- 33 Table
- 33 10-2 Rear Panel’s Input/Output
- 34 10-3 Specifications