advertisement
T-28 1.2m
Scan the QR code and select the Manuals and Support quick links from the product page for the most up-to-date manual information.
Scannen Sie den QR-Code und wählen Sie auf der Produktseite die Quicklinks Handbücher und Unterstützung, um die aktuellsten
Informationen zu Handbücher.
Scannez le code QR et sélectionnez les liens rapides Manuals and Support sur la page du produit pour obtenir les informations les plus récentes sur le manuel.
Scannerizzare il codice QR e selezionare i Link veloci Manuali e Supporto dalla pagina del prodotto per le informazioni manuali più aggiornate.
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni
EFL18350 EFL18375
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING : Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION : Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE : Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
AGE RECOMMENDATION: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others.
• Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Never operate your model with low transmitter batteries.
• Always keep aircraft in sight and under control.
• Always use fully charged batteries.
• Always keep transmitter powered on while aircraft is powered.
• Always remove batteries before disassembly.
• Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).
• Always keep moving parts clean.
• Always keep parts dry.
• Always keep all chemicals, small parts and anything electrical out of the reach of children.
• Always let parts cool after use before touching.
• Always remove batteries after use.
• Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics.
• Always ensure failsafe is properly set before flying.
• Never operate aircraft with damaged wiring.
• Never touch moving parts.
• Never place any portion of the model in your mouth as it could cause serious injury or even death.
WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum receiver found in a Horizon Hobby product, always purchase from
Horizon Hobby, LLC or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.
Important Federal Aviation Administration (FAA) Information
Use the QR code below to learn more about the Recreational UAS Safety Test
(TRUST), as was introduced by the 2018 FAA Reauthorization Bill. This free test is required by the FAA for all recreational flyers in the United States. The completed certificate must be presented upon request by any FAA or law enforcement official.
If your model aircraft weighs more than .55lbs or 250 grams, you are required by the FAA to register as a recreational flyer and apply your registration number to the outside of your aircraft. To learn more about registering with the FAA, use the QR code below.
2
T-28 Trojan 1.2m
EN
Quick Start Information
Transmitter Setup
Dual Rates*
1. Blank (Acro) Model
2. Wing Type: 1 Aileron, 1 Flap
3. Servo Reversing: Gear Reversed, All Others Normal
4. Travel Adjust (All Surfaces): 100%
Aileron
(at root)
Elevator
(at tip)
Rudder
(at top)
High Rate p = 16mm q = 16mm p = 15mm q = 15mm
= 20mm
= 20mm
Low Rate p = 9mm q = 9mm p = 10mm q = 8mm
= 13mm
= 13mm
Flap Travel Half q = 13mm Full q = 38mm
Flap-Down-Elevator
Compensation
2% 2%
Exponential
Aileron
Elevator
Rudder
High Rate
10%
10%
10%
Low Rate
5%
5%
5%
Center of Gravity (CG) 83mm +/- 19mm back from the front of the wing saddle
Flight Timer Setting 4 minutes
Specifications
Box Contents
Motor: Brushless Outrunner, 850Kv, 14 pole (EFLM4115) Installed Installed
ESC: Avian Lite 70-Amp ESC, 3S-4S, IC3 ® (SPMXAE70B) Installed Installed
Servos: (7) A330 9g Sub-Micro Servo (SPMSA330) Installed Installed
Retracts: (2) 15-size 90-degree main (EFLG1590M),
15-size 90-degree nose (EFLG1590N)
Installed Installed
Receiver: Spektrum ™ AR631 DSMX 6-Channel AS3X
Telemetry Receiver (SPMAR631)
Recommended Battery: 4S 14.8V 2200mAh 30C LiPo with IC3 ® /EC3 ™ connector (SPMX22004S30)
Recommended Battery Charger:
3 or 4-cell Li-Po battery balancing charger
Recommended Transmitter:
6+ channel, Full-Range 2.4GHz with Spektrum ™
DSM2 ® /DSMX ® technology and adjustable dual rates
Required to
Complete
Required to
Complete
Required to
Complete
Required to
Complete
Required to
Complete
Required to
Complete
48.23 in (1225mm)
Table of Contents
SAFE ® Select Technology .......................................................................................4
Preflight .................................................................................................................4
Transmitter Setup .................................................................................................4
Model Assembly ....................................................................................................5
Receiver Selection and Installation PNP .................................................................6
General Binding Tips and Failsafe BNF ...................................................................8
Transmitter and Receiver Binding / Enabling and Disabling SAFE Select BNF ..........8
SAFE ® Select Switch Designation ..........................................................................9
Control Surface Centering .....................................................................................9
Integrated ESC Telemetry .......................................................................................9
Battery Installation and ESC Arming .....................................................................10
Control Surface Direction .....................................................................................10
AS3X ® Control Response Test .............................................................................11
Propeller Installation ............................................................................................11
Center of Gravity (CG) .........................................................................................11
Dual Rates and Control Throws ............................................................................12
In Flight Trimming ................................................................................................12
Flying Tips and Repairs ........................................................................................12
Post Flight............................................................................................................13
Motor Service ......................................................................................................13
Troubleshooting Guide AS3X ................................................................................13
Troubleshooting Guide .........................................................................................14
Replacement Parts ...............................................................................................15
AMA National Model Aircraft Safety Code .............................................................15
Recommended Items ...........................................................................................15
Optional Items .....................................................................................................15
Limited Warranty .................................................................................................16
Contact Information .............................................................................................16
FCC Information ...................................................................................................17
IC Information ......................................................................................................17
Compliance Information for the European Union ...................................................17
Wi thout battery:
52oz (1.47kg)
Wi th 4S 2200mah battery:
60oz (1.7kg)
3
EN
SAFE
®
Select Technology
The BNF Basic version of this airplane includes SAFE Select technology which can offer an extra level of protection in flight. Use the following instructions to make the
SAFE Select system active and assign it to a switch. When enabled, SAFE Select prevents the airplane from banking or pitching past predetermined limits, and automatic self-leveling keeps the airplane flying in a straight and level attitude when the aileron, elevator and rudder sticks are at neutral.
SAFE Select is enabled or disabled during the bind process, or it can be enabled via Forward Programming. When the airplane is bound with SAFE Select enabled, a switch can be assigned to toggle SAFE Select ON or OFF. AS3X® technology remains active at all times.
Preflight
1. Remove and inspect contents.
2. Read this instruction manual thoroughly.
3. Charge the flight battery.
4. Setup Transmitter using transmitter setup chart.
5. Fully assemble the airplane.
6. Install the flight battery in the aircraft (once it has been fully charged).
7. Check the Center of Gravity (CG).
8. Bind the aircraft to your transmitter.
Transmitter Setup
Dual Rates
Take first flights in Low Rate. For landings, use high rate elevator.
NOTICE: To ensure AS3X ® technology functions properly, do not lower rate values below 50%. If lower rates are desired, manually adjust the position of the pushrods on the servo arm.
NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting Guide for more information.
Exponential
After first flights, you may adjust expo in your transmitter.
Telemetry Setup
See the Telemetry Setup table after binding. In order for the ESC and battery information to auto-populate in your transmitter’s telemetry menu, you must begin telemetry setup with the aircraft bound and connected.
SAFE Select can be configured three ways:
• SAFE Select Off: Always in AS3X mode
• SAFE Select On with no switch assigned: Always in SAFE Select mode
• SAFE Select On with a switch assigned
9. Make sure linkages move freely.
10. Perform the Control Direction Test with the transmitter.
11. Perform the AS3X Control Direction Test with the aircraft.
12. Adjust flight controls and transmitter.
13. Perform a radio system Range Test.
14. Install the propeller and spinner.
15. Find a safe open area to fly.
16. Plan flight for flying field conditions.
Computerized Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model reset), then name the model.
Set Dual Rates to
Set Servo Travel to
HIGH 100%
LOW 70%
100%
Set Throttle Cut to
Set Gear Channel to
-130%
Reverse
DXS
DX6i
DX7S
DX8
DX6e, DX8e
DX6, DX7, DX8
(Gen2)
DX9, DX18, DX20 iX12, iX20
NX6, NX8, NX10
Refer to spektrumrc.com for the appropriate download setup
1. Go to the SETUP LIST MENU
2. Set MODEL TYPE: ACRO
3. Go to ADJUST LIST MENU
4. Set FLAPS: Norm -100 Flap Elev 0
£ 100 Flap Elev 2
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set WING TYPE: 1 AIL 1 FLAP
4. Go to the FUNCTION LIST
5. Set FLAP SYSTEM: Choose Flap
NORM: -100% FLAP
MID: 0% FLAP
LAND: 100% FLAP
SPEED 2.0S: SWITCH = FLAP
2% Elevator
2% Elevator
1. Go to the SYSTEM SETUP (Model Utilities) †
2. Set MODEL TYPE: AIRPLANE
3. Set AIRCRAFT TYPE (Model Setup, Aircraft Type) † :
WING: 1 AIL 1 FLAP
4. Go to the FUNCTION LIST (Model Adjust) †
5. Set FLAP SYSTEM:
SELECT SWITCH D:
POS 0: -100% FLAP*
POS 1: 0% FLAP*
POS 2: 100% FLAP*
SPEED 2.0
2% Elevator
2% Elevator
4
* Flap programming values may vary slightly. For your initial flights use the recommended flap travel settings provided and adjust the flap travel to your preference on subsequent flights.
T-28 Trojan 1.2m
WARNING: Assemble the aircraft, program your radio control system, bind the aircraft, and verify correct operation before installing the propeller. Never attempt to program the radio components, assemble the aircraft or perform maintenance of any kind without removing the propeller or engaging throttle cut. Serious injury could result if the motor starts inadvertently with the propeller still attached.
Model Assembly
Horizontal Stabilizer Installation
1. Slide the horizontal stabilizer joiner into the hole in the rear of the fuselage.
2. Install the two piece (left and right) horizontal stabilizer as shown. Ensure the control horn faces down.
3. Secure the horizontal stabilizer pieces in place using the two included 2.6 x 12 mm self-tapping screws (Pack A) .
EN
2.6 x 12mm self-tapping counter sunk
5
EN
Wing Installation
1. Connect the Y harnesses as shown.
Flaps
Main Gear Retracts
Nose Gear Retract
Ailerons
Note: Verify polarity when connecting servo leads. The included Y-harnesses have a yellow signal wire which connects to the white wire on the servo lead.
• Flaps: Y-harness (Pack C) connects the flap servo plugs in center of wing with the receiver.
• Ailerons: Y-harness (Pack C) connects the aileron servo plugs in center of wing with the receiver.
• Gear: There is a 3-way Y-harness connected to the receiver with 2 open plugs. The servo plugs from the retracts mounted in the wing should be connected directly into the 3-way Y-harness in the receiver when installing the wing.
2. Locate the holes for the M3 x 32mm wing screws (Pack B) and begin to thread the screws into place.
3. Press the wing into place, being cautious to prevent pinching servo wires.
4. Tighten the wing screws.
Servo connector locks
The Y harnesses have a locking feature to secure the servo leads in place. Gently lift the locking tabs to remove the connector.
Receiver Selection and Installation
PNP
The recommended receiver for this aircraft is the Spektrum AR631. If you choose to install a different receiver, ensure that it is at least a 6-channel full range receiver. Refer to the manual of your chosen receiver for correct installation and operation instructions.
AR631 Installation
1. Connect the servos to the their respective ports in the receiver using the table at the right.
2. Using high quality double-sided servo tape (not included), mount the receiver to the flat area behind the battery compartment, as shown. The receiver should be mounted in the orientation shown, parallel to the length of the fuselage, with the label facing up and the servo ports facing the front of the aircraft. The orientation of the receiver is critical for all AS3X and SAFE technology setups.
NOTE: The rudder and nose gear servo have a Y-harness installed from factory.
The nose gear servo lead is labled “Rudd”, indicating it is plugged into the rudder channel.
CAUTION: Incorrect installation of the receiver could cause a crash.
Antenna Installation
The AR631 receiver has a coaxial style antenna. We recommend installing the antenna as far as possible from metal, batteries, or carbon fiber to maximize signal reception performance.
NOTICE: Do not cut, kink, or modify the antenna. Damage to the coaxial portion of an antenna will reduce the performance of the antenna. Shortening or cutting off the 31mm tip will reduce the range.
Active portion of antenna
6
AR631 Port Assignments
BND /PRG = SRXL2
1 = Throttle
2 = Ailerons
3 = Elevator
4 = Rudder
5 = Retracts
6 = Flaps
T-28 Trojan 1.2m
M3 x 32mm counter sunk machine screw
Connect the Pushrods to the Control Surfaces
1.
2.
3.
4.
Control Horn and Servo Arm Settings
The table to the right shows the factory settings for the control horns and servo arms.
Elevator
Ailerons
Rudder
Nose Gear
Flaps
Horns
N/A
Arms
7
EN
EN
General Binding Tips and Failsafe
BNF
• The included receiver has been specifically programmed for operation of this aircraft. Refer to the receiver manual for correct setup if the receiver is replaced.
• Keep away from large metal objects while binding.
• Do not point the transmitter’s antenna directly at the receiver while binding.
• The orange LED on the receiver will flash rapidly when the receiver enters bind mode.
• Once bound, the receiver will retain its bind settings for that transmitter until you re-bind.
• If the receiver loses transmitter communication, the failsafe will activate.
Failsafe moves the throttle channel to low throttle. Pitch and roll channels move to actively stabilize the aircraft in a descending turn.
• If problems occur, refer to the troubleshooting guide or if needed, contact the appropriate Horizon Product Support office.
Transmitter and Receiver Binding / Enabling and Disabling SAFE Select
BNF
The BNF Basic version of this airplane includes SAFE Select technology, enabling you to choose the level of flight protection. SAFE mode includes angle limits and automatic self leveling. AS3X mode provides the pilot with a direct response to the control sticks. SAFE Select is enabled or disabled during the bind process.
With SAFE Select disabled the aircraft is always in AS3X mode. With SAFE Select enabled the aircraft will be in SAFE Select mode all the time, or you can assign a switch to toggle between SAFE Select and AS3X modes.
Thanks to SAFE Select technology, this aircraft can be configured for full-time SAFE mode, full-time AS3X mode, or mode selection can be assigned to a switch.
IMPORTANT: Before binding, read the transmitter setup section in this manual and complete the transmitter setup table to ensure your transmitter is properly programmed for this aircraft.
IMPORTANT: Move the transmitter flight controls (rudder, elevators, and ailerons) and the throttle trim to neutral. Move the throttle to low before and during binding.
This process defines the failsafe settings.
You can use either the bind button on the receiver case or the conventional bind plug to complete the binding and SAFE Select process.
Using The Bind Button...
To Enable SAFE Select
Using The Bind Plug...
To Enable SAFE Select
Lower Throttle Connect Power Press and hold Bind Button
BIND
Install Bind Plug Lower Throttle Connect Power
Orange Flashing LED Bind TX to RX Release Bind Button
SAFE SELECT ENABLED: The control surfaces cycle back and forth twice with a slight pause at neutral position every time the receiver is powered on.
To Disable SAFE Select
Orange Flashing LED
BIND
Remove Bind Plug Bind TX to RX
SAFE SELECT ENABLED: The control surfaces cycle back and forth twice with a slight pause at neutral position every time the receiver is powered on.
To Disable SAFE Select
Lower Throttle Connect Power Press and hold Bind Button
BIND
Install Bind Plug Lower Throttle Connect Power
Orange Flashing LED Release Bind Button Bind TX to RX
SAFE SELECT DISABLED: The control surfaces cycle back and forth once every time the receiver is powered on.
SAFE Select can also be activated via Forward Programming in compatible transmitters.
Orange Flashing LED Bind TX to RX
BIND
Remove Bind Plug
SAFE SELECT DISABLED: The control surfaces cycle back and forth once every time the receiver is powered on.
8
T-28 Trojan 1.2m
SAFE
®
Select Switch Designation
BNF
Once SAFE Select is enabled, you can choose to fly in SAFE mode full-time, or assign a switch. Any switch on any channel between 5 and 9 can be used on your transmitter.
If the aircraft is bound with SAFE Select disabled, the aircraft will be in AS3X mode exclusively.
CAUTION: Keep all body parts well clear of the propeller and keep the aircraft securely restrained in case of accidental throttle activation.
IMPORTANT: To be able to assign a switch, first verify:
• The aircraft was bound with SAFE Select enabled.
• Your choice for the SAFE Select switch is assigned to a channel between
5 and 9 (Gear, Aux1-4), and travel is set at 100% in each direction.
• The aileron, elevator, rudder and throttle direction are set to normal, not reverse.
• The aileron, elevator, rudder and throttle are set to 100% travel. If dual rates are in use, the switches need to be in the 100% position.
See your transmitter manual for more information about assigning a switch to a channel.
Assigning a Switch with Stick Inputs
1. Power on the transmitter.
2. Power on the aircraft.
3. Hold both transmitter sticks to the inside bottom corners, and toggle the desired switch 5 times quickly (1 toggle = full up and down).
Mode 1 and 2 transmitters
Assigned Switch
100%
X 5
100%
Forward Programming
Assign the SAFE Select channel through forward programming on your compatible
Spektrum transmitter.
DX series,
NX series, iX series
Forward Programming SAFE Select Setup
1. Begin with the transmitter bound to the receiver.
2. Power ON the transmitter.
3. Assign a switch for SAFE Select that is not already in use for another function. Use any open channel between
5 and 9 (Gear, Aux1-4).
4. Set switch H (throttle cut) to prevent accidental motor operation.
5. Power ON the aircraft. A signal bar appears on your transmitter’s main screen when the telemetry information is being received.
6. Go to the FUNCTION LIST (Model Setup)
7. Select Forward Programming; Select Gyro Settings,
Choose SAFE Select to enter the menu.
8. Set SAFE Select Ch: To the channel you have chosen for SAFE
Select.
9. Set AS3X and SAFE On or Off as desired for each switch position.
For more information about setting SAFE Select and using Forward Programming, please refer to the following link for a detailed video: https://www.youtube.com/watch?v=o-46P066cik
EN
TIP: Use the channel monitor to verify channel movement.*
* This example of the channel monitor shows the stick positions for assigning a switch, the switch selection on Aux2, and +/- 100% travel on the switch.
-100 100 -100
Monitor
-100 -100 -100
THR AIL ELE RUD GER AX1 AX2 AX3 AX4
4. The control surfaces of the aircraft will move, indicating the switch has been selected.
Repeat the process to assign a different switch or to deactivate the current switch.
Integrated ESC Telemetry
BNF: This aircraft includes telemetry between the ESC and receiver, which can provide information including RPM, voltage, motor current, throttle setting (%), and
FET (speed controller) temperature.
PNP: The ESC in this aircraft is capable of delivering telemetry information over the throttle connection when paired with a Smart compatible Spektrum telemetry receiver. It will function with a normal PWM servo siganl for common radio control systems.
For more information about compatible transmitters, firmware updates, and how to use the telemetry technology on your transmitter, visit www.SpektrumRC.com.
DX series,
NX series, iX series
Telemetry Setup
1. Begin with the transmitter bound to the receiver.
2. Power ON the transmitter.
3. Set switch H (throttle cut) to prevent accidental motor operation.
4. Power ON the aircraft. A signal bar appears on your transmitter’s main screen when the telemetry information is being received.
5. Go to the FUNCTION LIST
6. Select TELEMETRY: Smart ESC
7. Set Total Cells: 4
8. Set LVC Alarm: 3.4V Set Alarm: Voice/Vibe
9. Set pole count: 14 pole
9
EN
Battery Installation and ESC Arming
The Spektrum ™ Smart 2200mAh 4S 30C Li-Po battery (SPMX22004S30) is recommended for best performance.
Refer to the Optional Parts List for other recommended batteries. If using a battery other than those listed, the battery should be within the range of capacity, dimensions and weight of the Spektrum Li-Po battery pack to fit in the fuselage.
Be sure the model balances at the recommended CG before flying.
WARNING: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement. If your transmitter supports it, always engage throttle cut before approaching the aircraft any time a battery is connected.
1. Lower the throttle and throttle trim to the lowest settings. Power on the transmitter, then wait 5 seconds.
2. Push back on the hatch release button behind the canopy and lift up on the rear of the hatch up to remove the hatch from the fuselage.
3. Install the fully charged battery in the middle of the battery compartment, as shown. Secure using the three included hook and loop straps.
4. Connect the battery to the ESC (the ESC is now armed).
5. Keep the aircraft immobile and away from wind or the system will not initialize.
• The ESC will sound a series of tones.
• An LED will light on the receiver.
• If the ESC sounds a continuous double beep after the flight battery is connected, recharge or replace the battery.
6. Push back on the hatch release botton before pressing down on the canopy to reinstall the canopy hatch.
IMPORTANT: The hatch release button will not engage by pressing down on the canopy. You must move the hatch release button back while lowering the canopy in order for it to engage.
Control Surface Direction
Switch on the transmitter and connect the battery. Use the transmitter to operate the aileron, elevator, and rudder controls. View the aircraft from the rear when checking the control directions.
Ailerons
1. Move the aileron stick to the left. The right aileron should move down and the left aileron up, which will cause the aircraft to bank left.
2. Move the aileron stick to the right. The right aileron should move up and the left aileron down, which will cause the aircraft to bank right.
Elevators
3. Pull the elevator stick back. The elevator should move up, which will cause the aircraft to pitch up.
4. Push the elevator stick forward. The elevator should move down, which will cause the aircraft to pitch down.
Rudder
5. Move the rudder stick to the left. The rudder should move to the left, which will cause the aircraft to yaw left.
6. Move the rudder stick to the right. The rudder should move to the right, which will cause the aircraft to yaw right.
10
T-28 Trojan 1.2m
AS3X
®
Control Response Test
WARNING: Do not perform any testing or maintenance with the propeller installed on the aircraft. Serious injury or property damage could result from the motor starting inadvertently.
This test ensures that the AS3X control system is functioning properly.
Assemble the aircraft and bind your transmitter to the receiver before performing this test.
1. Raise the throttle just above 25%, then lower the throttle to activate
AS3X technology.
WARNING: Keep all body parts, hair and loose clothing away from spinning motor, as these items could become entangled.
2. Move the entire aircraft as shown and ensure the control surfaces move in the direction indicated in the graphic. If the control surfaces do not respond as shown, do not fly the aircraft. Refer to the receiver manual for more information.
Once the AS3X system is active, control surfaces may move rapidly. This is normal.
AS3X remains active until the battery is disconnected.
Dual Rates and Control Throws
Program your transmitter to set the rates and control throws to the values given.
These values have been tested and are a good starting point to achieve successful flight.
After flying, you may choose to adjust the values for the desired control response.
Aileron
Elevator
Rudder
High Rate
p = 16mm q = 16mm p = 15mm q = 10mm
= 20mm
= 20mm
Low Rate
p = 9mm q = 9mm p = 10mm q = 8mm
= 13mm
= 13mm
Control Surface Centering
After assembly and transmitter setup, confirm that the control surfaces are centered. The model must be powered, bound to the transmitter in AS3X mode, with the throttle left at zero. When enabled, SAFE mode is active at power up.
AS3X mode is activated when the throttle is raised above 25% for the first time after being powered on. It is normal for the control surfaces to respond to aircraft movement if the aircraft is in AS3X or SAFE modes.
1. Verify the trims and subtrims on your transmitter are zero
2. Power up the model in AS3X mode and leave the throttle at zero
3. Look at the tip of each control surface and verify it is mechanically centered.
4. If adjustment is required, turn the clevis on the linkage to change the length of the linkage between the servo arm and the control horn.
Propeller Installation
WARNING: Do not install the propeller until the aircraft has been completely assembled, all the systems have been checked thoroughly and you are located at a suitable flying site.
WARNING: Never install a cracked, nicked or otherwise damaged propeller.
NOTICE: If the propeller is not balanced, the aircraft may vibrate, causing the stabilization system to not operate correctly and/or decrease the life of the servos.
1. Install the propeller, ensuring the embossed size numbers are facing forward.
2. Install the prop nut. Do not overtighten the prop nut as damage to the propeller or threads may result.
Aircraft movement
90˚
90˚
AS3X Reaction
EN
11
EN
Center of Gravity (CG)
The CG location is measured along the mold line on the bottom of the wing. The recommended starting location is 83mm back from the front of the wing saddle.
This CG location has been determined with the recommended Li-Po battery
(SPMX22004S30).
WARNING: Install the battery but do not arm the ESC while checking the
CG. Personal injury may result.
TIP: Measure the CG with the aircraft inverted.
83mm +/- 19mm
back from front of the wing saddle
Flying Tips and Repairs
Consult local laws and ordinances before choosing a flying location.
Range Check your Radio System
Before you fly, range check the radio system. Refer to your specific transmitter instruction manual for range test information.
Oscillation
Once the AS3X system is active (after advancing the throttle for the first time), you will normally see the control surfaces react to aircraft movement. In some flight conditions you may see oscillation (the aircraft rocks back and forth on one axis due to overcontrol). If oscillation occurs, refer to the Troubleshooting Guide for more information.
Takeoff
Place the aircraft facing into the wind. Set your transmitter in low rate and use your flaps switch to drop the flaps to takeoff or “half position”. Gradually increase the throttle to ¾ and steer with the rudder. Flaps make takeoffs shorter. Pull back gently on the elevator when the aircraft is up to speed. When airborne, flip your gear switch to raise your landing gear. Climb to a comfortable altitude and then flip your flaps switch to level the flaps.
Flying
For your first flights with the recommended battery pack (SPMX22004S30), set your transmitter timer or a stopwatch to 4 minutes, land the aircraft. Adjust your timer for longer or shorter flights once you have flown the model. If at any time the motor power reduces, land the aircraft immediately to recharge the flight battery. See the Low
Voltage Cutoff (LVC) section for more details on maximizing battery health and run time.
Landing
Land the aircraft into the wind. Use high rate Elevator for landings. Use a small amount of throttle for the entire descent. Lower the throttle to ¼ and select your flap switch to deploy the flaps to the landing, or full down position. Flaps will make the landing approach steeper and slower, and allow for a smoother landing. Flip your gear switch to lower your landing gear. This will slow the aircraft further.
Keep the throttle on until the aircraft is ready to flare. During flare, keep the wings level and the aircraft pointed into the wind. Gently lower the throttle while pulling back on the elevator to bring the aircraft down on its wheels.
If landing on grass, it is best to hold full up elevator after touchdown and when taxiing to prevent nosing over.
Once on the ground, avoid sharp turns until the plane has slowed enough to prevent scraping the wingtips.
NOTICE: If a crash is imminent, reduce the throttle and trim fully. Failure to do so could result in extra damage to the airframe, as well as damage to the ESC and motor.
NOTICE: After any impact, always ensure the receiver is secure in the fuselage.
If you replace the receiver, install the new receiver in the same orientation as the original receiver or damage may result.
NOTICE: Crash damage is not covered under warranty.
NOTICE: When you are finished flying, never leave the aircraft in direct sunlight or in a hot, enclosed area such as a car. Doing so can damage the aircraft.
Low Voltage Cutoff (LVC)
When a Li-Po battery is discharged below 3V per cell, it will not hold a charge. The
ESC protects the flight battery from over-discharge using Low Voltage Cutoff (LVC).
Before the battery charge decreases too much, LVC removes power supplied to the motor. Power to the motor reduces, showing that some battery power is reserved for flight control and safe landing.
Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge. Charge your Li-Po battery to about half capacity before storage.
During storage, make sure the battery charge does not fall below 3V per cell. LVC does not prevent the battery from over-discharge during storage.
NOTICE: Repeated flying to LVC will damage the battery.
TIP: Monitor your aircraft battery’s voltage before and after flying by using a
Li-Po Cell Voltage Checker (SPMXBC100, sold separately).
Repairs
Thanks to the EPO material in this aircraft, repairs to the foam can be made using virtually any adhesive (hot glue, regular CA, epoxy, etc). When parts are not repairable, see the Replacement Parts List for ordering by item number. For a listing of all replacement and optional parts, refer to the list at the end of this manual.
NOTICE: Use of CA accelerant on your aircraft can damage paint. DO NOT handle the aircraft until accelerant fully dries.
12
T-28 Trojan 1.2m
In Flight Trimming
During your first flight, trim the aircraft for level flight in AS3X mode, at 3/4 throttle with flaps up. Make small trim adjustments with your transmitter’s trim switches to straighten the aircraft’s flight path.
After adjusting the trim, do not touch the control sticks for 3 seconds. This allows the receiver to learn the correct settings to optimize AS3X performance.
Failure to do so could affect flight performance.
Post Flight
1. Disconnect the flight battery from the ESC (Required for safety and battery life).
2. Power OFF the transmitter.
3. Remove the flight battery from the aircraft.
4. Recharge the flight battery.
Motor Service
CAUTION: Always disconnect the flight battery before performing motor service.
Disassembly
1. Remove the spinner nut by using a small screwdriver or hex wrench.
2. Remove the propeller.
3. Remove the four screws from the front of the cowling and remove the dummy radial engine from the fuselage.
4. Remove the four 3 x 16mm screws and the motor with X-mount from the fuselage.
5. Disconnect the motor wires from the ESC wires.
6. Remove the four 3 x 6mm Phillips head machine screws and motor from the
X-mount.
Assembly
Assemble in reverse order.
• Correctly align and connect the motor wire colors with the ESC wires.
• Install the propeller with the size numbers facing forward. The propeller may require balancing.
NOTICE: If the propeller is not balanced, the aircraft may vibrate, causing the stabilization system to not operate correctly and/or decrease the life of the servos.
3 Seconds
5. Repair or replace all damaged parts.
6. Store the flight battery apart from the aircraft and monitor the battery charge.
7. Make note of the flight conditions and flight plan results, planning for future flights.
EN
Troubleshooting Guide AS3X
Oscillation
Problem
Inconsistent flight performance
Incorrect response to the AS3X
Control Response Test
Possible Cause
Damaged propeller or spinner
Imbalanced propeller
Motor vibration
Loose receiver
Loose aircraft controls
Worn parts
Irregular servo movement
Trim is not at neutral
Sub-Trim is not at neutral
Aircraft was not kept immobile for 5 seconds after battery connection
Incorrect direction settings in the receiver, which can cause a crash
Solution
Replace propeller or spinner
Balance the propeller
Replace parts or correctly align all parts and tighten fasteners as needed
Align and secure receiver in fuselage
Tighten or otherwise secure parts (servo, arm, linkage, horn and control surface)
Replace worn parts (especially propeller, spinner or servo)
Replace servo
If you adjust trim more than 8 clicks, adjust the clevis to remove trim
No Sub-Trim is allowed. Adjust the servo linkage
With the throttle stick in lowest position. Disconnect battery, then reconnect battery and keep the aircraft still for 5 seconds
DO NOT fly. Correct the direction settings (refer to the receiver manual), then fly
13
EN
Troubleshooting Guide
Problem
Aircraft will not respond to throttle but responds to other controls
Extra propeller noise or extra vibration
Reduced flight time or aircraft underpowered
Aircraft will not Bind
(during binding) to transmitter
Possible Cause Solution
Throttle not at idle and/or throttle trim too high
Throttle servo travel is lower than 100%
Throttle channel is reversed
Motor disconnected from ESC
Damaged propeller and spinner, collet or motor
Propeller is out of balance
Prop nut is too loose
Flight battery charge is low
Propeller installed backwards
Flight battery damaged
Flight conditions may be too cold
Battery capacity too low for flight conditions
Transmitter too near aircraft during binding process
Reset controls with throttle stick and throttle trim at lowest setting
Make sure throttle servo travel is 100% or greater
Reverse throttle channel on transmitter
Make sure motor is connected to the ESC
Replace damaged parts
Balance or replace propeller
Tighten the prop nut
Completely recharge flight battery
Install propeller with numbers facing forward
Replace flight battery and follow flight battery instructions
Make sure battery is warm before use
Replace battery or use a larger capacity battery
Move powered transmitter a few feet from aircraft, disconnect and reconnect flight battery to aircraft
Aircraft or transmitter is too close to large metal object, wireless source or another transmitter
Move aircraft and transmitter to another location and attempt binding again
The bind plug is not installed correctly in the bind port Install bind plug in bind port and bind the aircraft to the transmitter
Flight battery/transmitter battery charge is too low
Bind switch or button not held long enough during the bind process
Replace/recharge batteries
Power off transmitter and repeat bind process. Hold transmitter bind button or switch until receiver is bound
Aircraft will not connect (after binding) to transmitter
Control surface does not move
Controls reversed
Motor power pulses then motor loses power
Aircraft or transmitter is too close to large metal object, wireless source or another transmitter
Bind plug left installed in bind port
Aircraft bound to different model memory
(ModelMatch TM radios only)
Move aircraft and transmitter to another location and attempt connecting again
Rebind transmitter to the aircraft and remove the bind plug before cycling power
Select correct model memory on transmitter
Flight battery/Transmitter battery charge is too low
Transmitter may have been bound to a different aircraft using different DSM protocol
Replace/recharge batteries
Bind aircraft to transmitter
Control surface, control horn, linkage or servo damage Replace or repair damaged parts and adjust controls
Wire damaged or connections loose
Transmitter is not bound correctly or the incorrect airplanes was selected
Do a check of wires and connections, connect or replace as needed
Re-bind or select correct airplanes in transmitter
Flight battery charge is low Fully recharge flight battery
BEC (Battery Elimination Circuit) of the ESC is damaged Replace ESC
Transmitter settings are reversed Perform the Control Direction Test and adjust the controls on transmitter appropriately
ESC uses default soft Low Voltage Cutoff (LVC)
Weather conditions might be too cold
Battery is old, worn out, or damaged
Battery C rating might be too low
Recharge flight battery or replace battery that is no longer performing
Postpone flight until weather is warmer
Replace battery
Use recommended battery
14
T-28 Trojan 1.2m
Replacement Parts
Part #
EFL1228
EFL8302
EFL8307
EFL8312
EFL8313
EFL8314
EFL8315
EFL8320
EFL8323
EFL8324
EFL8325
EFL8326
EFLG1590M
EFLG1590N
EFLM4115
EFLP120703B
SPMSA330
SPMXAE45A
SPMAR631
Description
Motor X-Mount
Prop Adapter Hex 27mm: T-28 1.2m
Wheel Set: T-28 1.2m
Servo Wire Tape: T-28 1.2m
Painted Wing: T-28 1.2m
Pushrod Set w/ Clevis: T-28 1.2m
Hardware Set: T-28 1.2m
Horizontal Tail Set: T-28 1.2m
Decal Sheet: T-28: 1.2m 217
Canopy w/Latch: T-28 1.2m
Painted Fuselage: T-28 1.2m
Screw Set: T-28 1.2m
15-Size 90-Degree Main Retract Unit
15-Size 90-Degree Nose Retract Unit
BL15 Brushless Outrunner 850kV
Propeller 3 Blade 12 x 7
9g Sub Micro Servo
Spektrum 45 amp Smart-Lite ESC
AR631 6-Channel Receiver
Recommended Items
Part #
SPMAR631
SPMR6655
SPMX22004S30
SPMXC2020
Description
AR631 6CH AS3X/SAFE Receiver
DX6e 6 Ch Transmitter Only
2200mAh 4S 14.8V Smart G2 30C;
Smart S1200 G2 AC Charger,1x200W
Optional Items
Part #
SPMXCA300
SPMR6775
SPMR8200
SPMX22003S30
SPMX22004S30
SPMX223S50
SPMX224S50
SPMXBC100
SPMXC1080
SPMXC2040
Description
LiPo Charge Protection Bag,Large
NX6 6 Ch DSMX Transmitter Only
NX8 8 Ch DSMX Transmitter Only
2200mAh 3S 11.1V Smart 30C; IC3
2200mAh 4S 14.8V Smart 30C; IC3
2200mAh 3S 11.1V Smart G2 50C;
2200mAh 4S 14.8V Smart G2 50C;
Smart Battery & Servo Tester
Smart S1100 AC Charger, 1x100W
Smart S1400 G2 AC Charger,1x400W
AMA National Model Aircraft Safety Code
Effective January 1, 2018
A model aircraft is a non-human-carrying device capable of sustained flight within visual line of sight of the pilot or spotter(s). It may not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. All model flights must be conducted in accordance with this safety code and related AMA guidelines, any additional rules specific to the flying site, as well as all applicable laws and regulations.
As an AMA member I agree:
• I will not fly a model aircraft in a careless or reckless manner.
• I will not interfere with and will yield the right of way to all human-carrying aircraftusing AMA’s See and Avoid Guidance and a spotter when appropriate.
• I will not operate any model aircraft while I am under the influence of alcohol or any drug that could adversely affect my ability to safely control the model.
• I will avoid flying directly over unprotected people, moving vehicles, and occupied structures.
• I will only fly models weighing more than 55 pounds, including fuel, if certified through AMA’s Large Model Airplane Program.
• I will only fly a turbine-powered model aircraft in compliance with AMA’s Gas
Turbine Program.
• I will not fly a powered model outdoors closer than 25 feet to any individual, except for myself or my helper(s) located at the flightline, unless I am taking off and landing, or as otherwise provided in AMA’s Competition Regulation.
• I will fly Free Flight (FF) and Control Line (CL) models in compliance with AMA’s safety programming.
• I will use an established safety line to separate all model aircraft operations from spectators and bystanders.
• I will maintain visual contact of an RC model aircraft without enhancement other than corrective lenses prescribed to me. When using an advanced flight system, such as an autopilot, or flying First-Person View (FPV), I will comply with AMA’s
Advanced Flight System programming.
EN
15
EN
Limited Warranty
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon
Hobby authorized service center, (v) Product not purchased from an authorized
Horizon dealer, or (vi) Product not compliant with applicable technical regulations, or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER
WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE
PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED
USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that
Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all
Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL
LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER
THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon
Contact Information
Country of Purchase Horizon Hobby
Horizon Service Center (Repairs and Repair Requests)
United States of America
Horizon Product Support (Product Technical Assistance)
European Union
Sales
Horizon Technischer Service
Sales: Horizon Hobby GmbH to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.
horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return
Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.
com/content/service-center_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date.
Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost . By submitting the item for service you are agreeing to payment of the service without notification.
Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American
Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced
Product, through a carrier of the sender’s choice and at the sender’s expense.
Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.
10/15
Contact Information
servicecenter.horizonhobby.com/RequestForm/ [email protected]
877-504-0233 [email protected]
800-338-4639 [email protected]
+49 (0) 4121 2655 100
Address
2904 Research Rd
Champaign, Illinois, 61822 USA
Hanskampring 9
D 22885 Barsbüttel, Germany
16
T-28 Trojan 1.2m
FCC Information
FCC ID: BRWSPMSR6200A
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and/or antenna and your body
(excluding fingers, hands, wrists, ankles and feet). This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter.
Supplier’s Declaration of Conformity
T-28 1.2m (EFL18350/EFL18375)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
IC Information
IC: 6157A-SPMSR6200A
CAN ICES-3 (B)/NMB-3(B)
This device contains license-exempt transmitter(s)/receivers(s) that comply with
Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following 2 conditions:
Horizon Hobby, LLC
2904 Research Rd.,
Champaign, IL 61822
Email: [email protected]
Web: HorizonHobby.com
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Compliance Information for the European Union
EU Compliance Statement:
T-28 1.2m PNP (EFL18375) ; Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following:
EU EMC Directive 2014/30/EU; RoHS 2 Directive 2011/65/EU; RoHS 3
Directive - Amending 2011/65/EU Annex II 2015/863.
T-28 1.2m BNF Basic (EFL18350) ; Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following: EU Radio Equipment Directive 2014/53/
EU; RoHS 2 Directive 2011/65/EU; RoHS 3 Directive - Amending 2011/65/EU Annex
II 2015/863.
The full text of the EU declaration of conformity is available at the following internet address: https://www.horizonhobby.com/content/support-render-compliance.
Wireless Frequency Range and Wireless Output Power:
Receiver:
2404-2476MHz / 5.58dBm
EU Manufacturer of Record:
Horizon Hobby, LLC
2904 Research Road
Champaign, IL 61822 USA
EU Importer of Record:
Horizon Hobby, GmbH
Hanskampring 9
22885 Barsbüttel Germany
WEEE NOTICE:
This appliance is labeled in accordance with European Directive
2012/19/EU concerning waste of electrical and electronic equipment
(WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.
EN
17
Created 11/21
© 2021 Horizon Hobby, LLC.
E-flite, Avian, DSM, DSM2, DSMX, Bind-N-Fly, BNF, the BNF logo, Plug-N-Play, AS3X, SAFE, the SAFE logo, ModelMatch, IC3, EC3, and the
Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
All other trademarks, service marks and logos are property of their respective owners.
US 8,672,726. US 9,056,667. US 9,753,457. US 9,930,567. US 10,078,329. US 10,419,970. US 10,849,013. Other patents pending.
https://www.horizonhobby.com/content/e-flite-rc
EFL18350, EFL18375 158509.1
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project