advertisement
Quad Lift
3
1
2
2
1
2
1
WARNING
Do not put a lift truck into service if the chain wear indication is 2% or more. A Reading of 2% or more could cause damage or injury to persons.
1. Maximum chain wear ................. Less than 2%
(See Chain Wear in TESTING & ADJUSTING).
2. Put LOCTITE NO. 242 Thread Lock on the threads of the relay group locknuts after adjustment of the lift chains is completed.
3. Tighten bolts until contact is made with guide assembly.
4. Distance from bottom of inner mast to bottom of lower bearing on carriage must be 41±1.5 mm
(1.61 ± 0.6 in). Bottom of inner mast be even
(flush) with bottom of stationary mast. Adjust inner mast first
Vehicle System 13 Specification
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Hydraulic Control Valve
- 8 Hydraulic Pump
- 8 Lift Cylinders
- 9 Full Free Triple Lift and Full Free Lift Primary
- 9 Lift Secondary
- 10 Tilt Cylinder
- 11 Carriage
- 12 Lift Relay Group
- 12 Standard Lift
- 13 Full Free Lift
- 14 Full Free Triple
- 15 Quad Lift
- 16 Lift & Tilt Mounting Group
- 17 Steering Wheel
- 18 Steering Gear
- 19 Steer Axle and Wheel
- 20 Steer Tire Installation
- 20 (GC Models Only)
- 20 Steer Wheel Mounting
- 20 Oil Cooled Disc Brake
- 21 Parking Brake
- 22 Hydraulic Schematic
- 24 Control Valve
- 24 External Configuration
- 24 Hydraulic Circuit
- 25 Inlet Block - Key On
- 26 Lift Spool - Positioned to Lift
- 27 Lift Spool - Positioned to Lower
- 27 Tilt Spool - Positioned for Forward Tilt
- 28 Tilt Spool - Positioned for Backward Tilt
- 29 Shifting
- 29 Pressure and Flow Control Section
- 30 Flow Control Adjustment - Tilt and Auxiliary
- 31 STEERING SYSTEM
- 31 Hydraulic Schematic
- 32 Steering Cylinder
- 33 Steering Gear
- 35 Brake Power Master Cylinder
- 37 Oil Cooled Disc Brake
- 37 Parking Brake
- 38 Delayed Engine Shutdown System
- 38 Operation
- 40 System
- 40 Diagnostic Fault Codes
- 44 OSS (Operator Sensing System)
- 45 Operation
- 45 Symbols of OSS
- 46 Operator Sensing System Schematic
- 49 Troubleshooting
- 49 Visual Checks
- 49 Performance Test
- 51 Hydraulic System and Mast
- 52 Hydraulic Pump
- 53 Hydraulic Control Valve
- 54 Lift and Tilt Cylinders
- 55 Steering System
- 56 Power Master Cylinder
- 57 Brake System
- 58 Hydraulic System
- 58 Relief Valve Pressure Check
- 60 Standard Lift Cylinder Air Removal
- 61 Mast and Carriage
- 61 Mast Adjustment - STD, FFL & FFT
- 66 Mast Adjustment - Quad
- 71 Carriage Adjustment
- 73 Quad Mast
- 74 Chain Adjustment
- 75 Chain Wear Test
- 76 Carriage and Mast Height Adjustment
- 76 Forks Parallel Check
- 77 Tilt Cylinder Alignment
- 79 Drift Test
- 80 Steering System
- 80 Steer Wheel Bearing Adjustment
- 80 Steering Axle Stop Adjustment
- 81 Steering System Pressure Check
- 83 Brake System
- 83 Brake System Air Removal
- 83 Parking Brake Test
- 84 Parking Brake Adjustment