advertisement
Part 6
FORM Menu Functions
This part of the manual describes how to use the FORM menu to layout your text exactly the way you want it on the label. With the FORM menu, you can control character pitch, text blocks, text alignment, and a wide range of other features.
Fundamentals of Label Layout
Before we actually begin our discussion about how to layout a tape, we should first define a few terms. Note the following illustration.
Label Length
Print Area
ABCD EFGH IJKLMN QRS TU VWZYZ
Side space Blocks Side space
• Blocks
A block is text that is enclosed between two block marks ( ). Note that the first (far left) block does not require a block mark at the beginning, and the last (far right) block does not require a block mark at the end. If there are no block marks, all of the text is treated as a single block. You can individually specify the length of each block, as well as the pitch and the number of lines inside each block.
• Print Area
The print area is the actual area of a label that contains printed text. It starts with the left side of the first character printed, and ends with the right side of the last character printed.
• Side Spaces
The side spaces are blank areas that the Label Printer automatically adds on either end of the print area. Note that side spaces are only added when you are using auto feed, and they are not added when using manual feed (see “Auto Feed”).
Auto Feed (with long side spaces)
A B X Y Z
Auto Feed (with short side spaces)
A B X Y Z
37
advertisement
Related manuals
advertisement
Table of contents
- 5 Getting Acquainted
- 5 Important Precautions
- 7 General Guide
- 9 Label Printer Menus
- 10 Getting Ready
- 10 Power Supply
- 10 Replacing Batteries
- 11 To replace the memoryback-up battery
- 11 To replace the main batteries
- 12 AC Adaptor
- 12 To connect the AC adaptor
- 12 Switching Power On and Off
- 12 Resetting the Memory
- 12 To reset the memory
- 13 Power On Recall Function
- 13 Auto Power Off Function
- 13 Tape Cartridges
- 13 To load a tape cartridge
- 15 To specify the tape width
- 16 Display Contrast
- 16 Sound Effects
- 16 switching power on
- 16 To switch sound effects on and off
- 17 Setting the message language
- 17 To set the message language
- 17 Setting the unit of measurement
- 18 Demo Print
- 18 other than 6mm
- 18 6mm tape
- 19 and Illustrations
- 19 Display Symbols and Indicators
- 21 Basic Alpha-Numeric Input
- 21 To input alpha-numeric characters
- 22 About the CODE key
- 22 To input special symbols
- 23 To input illustrations
- 24 Characters
- 24 Moving the Cursor
- 24 To move the cursor
- 24 Deleting Individual Characters
- 24 To delete characters using the BS key
- 25 To delete characters using the DEL key
- 25 Deleting a Series of Characters
- 25 To delete a series of characters
- 25 Using the CLS Function
- 25 To clear all text from the display
- 26 To clear specific text
- 26 Overwrite and Insert
- 26 Overwrite
- 27 Insert
- 27 To switch between overwrite and insert
- 28 Text Effects
- 28 Specifying Character Attributes
- 28 characters
- 29 of text
- 29 existing text
- 30 Changing Fonts
- 30 How to tell the current font settings
- 30 To change the font setting
- 31 Changing Character Styles
- 31 How to tell the current style settings
- 32 To change the style setting
- 33 Changing Character Size
- 33 About Auto Fit
- 33 About the FIT mark
- 34 How to tell the current size settings
- 34 To change the characters size
- 35 Assigning Text Effects
- 35 Changing Text Effects
- 35 To assign text effects
- 36 To remove text effects
- 38 FORM Menu Functions
- 38 Fundamentals of Label Layout
- 39 Creating and Deleting Blocks
- 39 To create a block
- 39 To delete a block mark
- 39 Character Pitch
- 39 To specify the character pitch
- 40 Block Length
- 40 To specify a block length
- 41 To cancel block length settings
- 42 Tape Length
- 42 To select a preset tape length
- 43 To specify your own tape length
- 44 To cancel a tape length setting
- 44 Auto Feed
- 45 To select a feed option
- 45 Block Spacing
- 45 To specify the block spacing
- 45 To specify vertical printing
- 46 Mirror Image
- 46 To specify mirror image
- 46 Text Alignment
- 47 To specify text alignment
- 48 Justification
- 48 To switch justification on and off
- 49 Quick Formats
- 50 To select a built-in format
- 51 To cancel a built-in format
- 52 Presets
- 52 Using the presets menu
- 52 Preset (Auto) Layouts
- 52 a label
- 54 preset layout
- 54 memory
- 57 Preset Phrases
- 57 To print a preset phrases
- 57 Numbering
- 57 To print a numbered series
- 59 Printing
- 59 Printing a Tape
- 59 To print a tape
- 60 To show the image display
- 60 To show the layout display
- 60 To feed tape
- 61 To adjust the print density
- 61 Frame Printing
- 61 of the printing area
- 63 Part 10 Memory
- 63 Storing Data
- 63 To store data into memory
- 63 Recalling Data
- 64 To recall data from memory
- 64 Deleting Text
- 65 To delete text from memory
- 66 Part 11 Reference
- 66 Cleaning the Printer Head and Roller
- 66 To clean the printer head and roller
- 67 Resetting
- 68 About the Label Printer’s Keys
- 70 Troubleshooting
- 72 Messages
- 73 Initial Settings
- 74 Symbols, Illustrations and Frames
- 75 Preset (Auto) Layouts
- 79 Application Examples
- 80 Specifications