- Computers & electronics
- Print & Scan
- Bar code readers
- Datalogic
- Magellan 3300HSi
- Operating instructions
advertisement
Chapter 6
Symbologies
The scanner supports the following symbologies (bar code types). Options for each symbology are included in this chapter.
• GS1 DataBar Omnidirectional /
Factory Defaults— for the standard RS-232 interface are indicated in bold text throughout this
section. Reference Appendix D, Factory Default Settings
for default exceptions for your interface.
UPC-A
Disable/Enable UPC-A
When disabled, the scanner will not read UPC-A bar codes.
START / END
PROGRAMMING bar codes
Disable UPC-A
Enable UPC-A
DEFAULT
85
Product Reference Guide
Symbologies
UPC-A — continued
Check Digit Transmission
Enable this option to transmit the check digit along with UPC-A bar code data.
START / END
PROGRAMMING bar codes
Don’t Send Check Digit
³ 0 0 0 0
Send Check Digit
DEFAULT
Number System Transmission
This feature enables/disables transmission of UPC-A System Number.
START / END
PROGRAMMING bar codes
Disable Number System Transmission
Enable Number System Transmission
DEFAULT
86
Magellan TM 3300HSi
UPC-A
UPC-A — continued
Expand UPC-A to EAN-13
Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13.
START / END
PROGRAMMING bar codes
Don’t Expand to EAN-13
DEFAULT
Expand to EAN-13
Product Reference Guide 87
Symbologies
UPC-E
The following options apply to the UPC-E symbology.
Disable/Enable UPC-E
When disabled, the scanner will not read UPC-E bar codes.
START / END
PROGRAMMING bar codes
Disable UPC-E
Enable UPC-E
DEFAULT
Check Digit Transmission
Enable this option to transmit the check digit along with UPC-E bar code data.
START / END
PROGRAMMING bar codes
Don’t Send Check Digit
Send Check Digit
DEFAULT
88
Magellan TM 3300HSi
UPC-E — continued
Number System Digit
The Number System Digit (NSD) which is always a zero (0) in the leading position can be optionally included (or not) with scanned bar code data.
UPC-E
START / END
PROGRAMMING bar codes
Exclude Number System Digit
DEFAULT
Include Number System Digit
³ 0 2 8 0 1
Expand to UPC-E to UPC-A
Enables/disables expansion of UPC-E labels to UPC-A.
Selecting this feature also changes the symbology ID to match those required for UPC-A.
START / END
PROGRAMMING bar codes
Don’t Expand UPC-E to UPC-A
DEFAULT
Expand UPC-E to UPC-A
Product Reference Guide 89
Symbologies
UPC-E — continued
Expand UPC-E to EAN13
Enables/disables expansion of UPC-E labels to EAN-13. Selecting this feature also changes the symbology ID to match those required for EAN-13.
START / END
PROGRAMMING bar codes
Don’t Expand UPC-E to EAN-13
DEFAULT
Expand UPC-E to EAN-13
90
Magellan TM 3300HSi
UPC-E
GTIN
The following options apply to the GTIN label data format.
Expand UPC/EAN to GTIN
When this feature is enabled, the scanner will translate UPC/EAN labels to the 14 digit GTIN format.
START / END
PROGRAMMING bar codes
Don’t Expand to GTIN
DEFAULT
Expand to GTIN
Product Reference Guide 91
Symbologies
EAN-13
The following options apply to the EAN-13 symbology.
Disable/Enable EAN-13
When disabled, the scanner will not read EAN-13 bar codes.
START / END
PROGRAMMING bar codes
Disable EAN-13
Enable EAN-13
DEFAULT
Check Digit Transmission
Enable this option to transmit the check digit along with EAN-13 bar code data.
START / END
PROGRAMMING bar codes
Don’t Send Check Digit
Send Check Digit
DEFAULT
92
Magellan TM 3300HSi
EAN-13
EAN-13 — continued
EAN-13 Flag 1 Character
Enables/disables transmission of an EAN/JAN13 Flag1 character.
START / END
PROGRAMMING bar codes
Don’t Transmit EAN-13 Flag 1 Char
Transmit EAN-13 Flag 1 Char
DEFAULT
ISBN
When enabled, this feature truncates the leading three digits from labels that contain ISBN
(International Standard Book Number) and appends an ISBN check character to the end of the label. These codes are used for books and magazines. Labels with ISBN codes start with "978".
Example:
Bar Code data:
Output:
“9789572222720”
“9572222724”
START / END
PROGRAMMING bar codes
Disable ISBN
DEFAULT
Enable ISBN
Product Reference Guide 93
Symbologies
EAN-8
The following options apply to the EAN-8 symbology.
Disable/Enable EAN-8
When disabled, the scanner will not read EAN-8 bar codes.
START / END
PROGRAMMING bar codes
Disable EAN-8
Enable EAN-8
DEFAULT
Check Digit Transmission
Enable this option to transmit the check Digit along with EAN-8 bar code data.
START / END
PROGRAMMING bar codes
Don’t Send Check Digit
Send Check Digit
DEFAULT
94
Magellan TM 3300HSi
EAN-8
EAN-8 — continued
Expand EAN-8 to EAN-13— Expands EAN-8 data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13.
START / END
PROGRAMMING bar codes
Don’t Expand to EAN-13
DEFAULT
Expand to EAN-13
Product Reference Guide 95
Symbologies
EAN Two-Label
Enables/disables the ability of the scanner to decode EAN two-label pairs.
START / END
PROGRAMMING bar codes
Disable EAN Two-Label
Enable EAN Two-Label
EAN Two-Label Combined Transmission
Enables/disables the transmitting of an EAN two label pair as one label.
START / END
PROGRAMMING bar codes
EAN Two-Label Combined Transmission = Disable
DEFAULT
EAN Two-Label Combined Transmission = Enable
96
Magellan TM 3300HSi
Price Weight Check Digit
Price Weight Check Digit
Enables/disables calculation and verification of price/weight check digits.
Applies to all UPC-A labels with a number-system character of
2 and EAN/JAN 13 labels with a
1 digit of 2
NOTE
Here are the available options for this feature:
• Disable
• Enable 4-digit price/wt check-digit calculation
• Enable 5-digit price/wt check-digit calculation
• Enable European 4-digit price-weight check-digit calculation
• Enable European 5-digit price-weight check-digit calculation
START / END
PROGRAMMING bar codes
Price Weight Check Digit = Disable
DEFAULT
Price Weight Check Digit = Enable 4-digit price/wt
Price Weight Check Digit = Enable 5-digit price/wt
Price Weight Check Digit = Enable European 4-digit price/wt
Price Weight Check Digit = Enable European 5-digit price/wt
Product Reference Guide 97
Symbologies
Add-ons
Add-ons (or supplemental characters) are commonly added to the end of UPC/EAN bar codes.
The scanner will read the add-ons if they are enabled and in the field of view. Three add-on types are supported: 2-digit, 5-digit and Code 128 add-ons. Supported options are:
None— This option directs the scanner to ignore add-on portion of a UPC/EAN bar code but still read the main portion of the bar code.
2 Digits— The scanner will optionally read 2-digit add-ons with the UPC/EAN label.
5 Digits— The scanner will optionally read 5-digit add-ons with the UPC/EAN label.
Code 128 Add-on— The scanner will optionally read Code 128 add-ons with the UPC/EAN label.
Contact Customer Support for advanced programming of optional and conditional add-ons.
NOTE
98
Magellan TM 3300HSi
Add-ons — continued
START / END
PROGRAMMING bar codes
Disable Optional 2-Digit Add-ons
DEFAULT
Enable Optional 2-Digit Add-ons
Disable Optional 5-Digit Add-ons
DEFAULT
Enable Optional 5-Digit Add-ons
³ 0 1 1 0 1
Disable Optional Code 128 Add-ons
DEFAULT
Enable Optional Code 128 Add-ons
Add-ons
Product Reference Guide 99
Symbologies
GS1 DataBar Omnidirectional / Stacked Omnidirectional
The following options apply to the GS1 DataBar Omnidirectional symbology.
Disable/Enable GS1 DataBar Omnidirectional
When this feature is disabled, the scanner will not read GS1 DataBar Omnidirectional bar codes.
START / END
PROGRAMMING bar codes
Disable GS1 DataBar Omnidirectional
DEFAULT
Enable GS1 DataBar Omnidirectional
UCC/EAN 128 Emulation
When enabled, GS1 DataBar Omnidirectional bar codes will be translated to the UCC/EAN
128 label data format.
START / END
PROGRAMMING bar codes
Disable UCC/EAN 128 Emulation
DEFAULT
Enable UCC/EAN 128 Emulation
100
Magellan TM 3300HSi
GS1 DataBar Expanded / Expanded Stacked
GS1 DataBar Expanded / Expanded Stacked
The following options apply to the GS1 DataBar Expanded symbology.
Disable/Enable GS1 DataBar Expanded
When this feature is disabled, the scanner will not read GS1 DataBar Expanded bar codes.
START / END
PROGRAMMING bar codes
Disable GS1 DataBar Expanded
DEFAULT
Enable GS1 DataBar Expanded
GS1-128 Emulation
When enabled, GS1 DataBar Expanded bar codes will be translated to the GS1-128 label data format.
START / END
PROGRAMMING bar codes
Disable GS1-128 Emulation
DEFAULT
Enable GS1-128 Emulation
Product Reference Guide 101
Symbologies
GS1 DataBar Expanded / Expanded Stacked — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable Length 1 and Length 2 values.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
GS1 DataBar Expanded Length 1, Length 2 Programming Instructions
See
Length 1, Length 2 Programming Instructions on page 154 for
detailed instructions on setting this feature.
For GS1 DataBar Expanded bar codes, only the data characters are included in the length calculations.
NOTE
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 01
Set Length 2
102
Magellan TM 3300HSi
GS1 DataBar Expanded / Expanded Stacked
GS1 DataBar Expanded / Expanded Stacked — continued
Coupon Read Control
This feature controls coupon reading.
START / END
PROGRAMMING bar codes
Disable coupon filtering
Enable UPCA coupon decoding
Disable GS1 DataBar coupon decoding
DEFAULT
Enable GS1 DataBar coupon decoding
Disable UPCA coupon decoding
Product Reference Guide 103
Symbologies
GS1 DataBar Limited
The following options apply to the GS1 DataBar Limited symbology.
Disable/Enable GS1 DataBar Limited
When this feature is disabled, the scanner will not read GS1 DataBar Limited bar codes.
START / END
Enable GS1 DataBar Limited
PROGRAMMING bar codes
Disable GS1 DataBar Limited
DEFAULT
GS1-128 Emulation
When enabled, GS1 DataBar Limited bar codes will be translated to the GS1-128 label data format.
START / END
PROGRAMMING bar codes
Disable GS1-128 Emulation
DEFAULT
Enable GS1-128 Emulation
104
Magellan TM 3300HSi
Code 39
Code 39
The following options apply to the Code 39 symbology.
Disable/Enable Code 39
When this feature is disabled, the scanner will not read Code 39 bar codes.
START / END
PROGRAMMING bar codes
Disable Code 39
Enable Code 39
DEFAULT
Check Character Calculation
When enabled, the scanner will calculate the check character of the labels. Turn this option on only when a checksum is present in the Code 39 labels.
START / END
PROGRAMMING bar codes
Disable Check Char Calculation
DEFAULT
Enable Check Char Calculation
Product Reference Guide 105
Symbologies
Check Character Transmit
Enable this option to transmit the check character with scanned bar code data.
START / END
PROGRAMMING bar codes
Disable Check Char Transmission
Enable Check Char Transmission
DEFAULT
Start/Stop Characters
Enables/disables transmission of Code39 start and stop characters.
START / END
PROGRAMMING bar codes
Don’t Transmit Start/Stop Characters
DEFAULT
Transmit Start/Stop Characters
106
Magellan TM 3300HSi
Code 39 Full ASCII
Enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters .
Code 39
START / END
PROGRAMMING bar codes
Disable Code 39 Full ASCII
DEFAULT
Enable Code 39 Full ASCII
Product Reference Guide 107
Symbologies
Code 39 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable Length 1 and Length 2 values.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Code 39 Length 1, Length 2 Programming Instructions
See
Length 1, Length 2 Programming Instructions on page 154 for
detailed instructions on setting this feature.
For Code 39 bar codes, all check, data and full
ASCII shift characters are included in the length calculations. Start/Stop characters are not included.
NOTE
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 02
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 50
108
Magellan TM 3300HSi
Code 32 Italian Pharmacode
Code 32 Italian Pharmacode
The following options apply to the Code 32 Italian Pharmacode symbology.
Disable/Enable Code 32 Italian Pharmacode
When this feature is disabled, the scanner will not read Code 32 Italian Pharmacode bar codes.
START / END
PROGRAMMING bar codes
Disable Code 32 Italian Pharmacode
DEFAULT
Enable Code 32 Italian Pharmacode
Start/Stop Characters
Enables or disables transmission of Code 32 Italian Pharmacode start/stop characters.
START / END
PROGRAMMING bar codes
Don’t Transmit Start/Stop Characters
DEFAULT
Transmit Start/Stop Characters
³ 0 0 6 0 1
Product Reference Guide 109
Symbologies
Code 32 Italian Pharmacode — continued
Check Character Transmit
Enable this option to transmit the check character with scanned bar code data.
START / END
PROGRAMMING bar codes
Disable Check Char Transmission
Enable Check Char Transmission
DEFAULT
110
Magellan TM 3300HSi
Code 128
The following options apply to the Code 128 symbology.
Disable/Enable Code 128
When this feature is disabled, the scanner will not read Code 128 bar codes.
START / END
PROGRAMMING bar codes
Disable Code 128
Enable Code 128
DEFAULT
Code 128
Disable/Enable EAN 128
When this feature is disabled, the scanner will not read EAN 128 bar codes.
START / END
PROGRAMMING bar codes
Disable EAN 128
Enable EAN 128
DEFAULT
Product Reference Guide 111
Symbologies
Code 128 — continued
Transmit Function Characters
Enables/disables transmission of Code 128 function characters 1, 2, 3, and 4.ï€
Function codes are transmitted as follows:
• FNC1 = 80 hex
• FNC2 = 81 hex
• FNC3 = 82 hex
• FNC4 = 83 hex
START / END
PROGRAMMING bar codes
Don’t Transmit Function Characters
DEFAULT
Transmit Function Characters
112
Magellan TM 3300HSi
Code 128
Code 128 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable Length 1 and Length 2 values.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Code 128 Length 1, Length 2 Programming Instructions
See
Length 1, Length 2 Programming Instructions on page 154 for
detailed instructions on setting this feature.
For Code 128 bar codes, only the data characters are included in the length calculations.
NOTE
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 01
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 80
Product Reference Guide 113
Symbologies
Code 128 Conversion to Code 39
Enables/disables expansion of Code 128 labels to Code 39.
START / END
PROGRAMMING bar codes
Disable
DEFAULT
Enable
Interleaved 2 of 5
The following options apply to the Interleaved 2 of 5 (I 2 of 5) symbology.
Disable/Enable Interleaved 2 of 5
When this feature is disabled, the scanner will not read Interleaved 2 of 5 bar codes.
START / END
PROGRAMMING bar codes
Disable Interleaved 2 of 5
DEFAULT
Enable Interleaved 2 of 5
114
Magellan TM 3300HSi
Interleaved 2 of 5
Check Digit Calculation
When enabled, the scanner will calculate the check digit of the labels.
START / END
PROGRAMMING bar codes
Disable Check Digit Calculation
DEFAULT
Enable Check Digit Calculation
Check Digit Transmit
Enable this option to transmit the check digit with scanned bar code data.
START / END
PROGRAMMING bar codes
Disable Check Digit Calculation
DEFAULT
Enable Check Digit Calculation
Product Reference Guide 115
Symbologies
Interleaved 2 of 5 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable Length 1 and Length 2 values.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Interleaved 2 of 5 Length 1, Length 2 Programming Instructions
See
Length 1, Length 2 Programming Instructions on page 154 for
detailed instructions on setting this feature.
For Interleaved 2 of 5 bar codes, lengths must be an even number. Additionally, all check and data characters are included in the length calculations.
NOTE
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 06
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 50
116
Magellan TM 3300HSi
Codabar
The following options apply to the Codabar symbology.
Disable/Enable Codabar
When this feature is disabled, the scanner will not read Codabar bar codes.
START / END
PROGRAMMING bar codes
Disable Codabar
DEFAULT
Enable Codabar
Check Character Verification
When enabled, the scanner will verify the check character of the labels.
START / END
PROGRAMMING bar codes
Disable Check Char Verification
DEFAULT
Enable Check Char Verification
Codabar
Product Reference Guide 117
Symbologies
Check Character Transmit
Enable this option to transmit the check character with scanned bar code data.
START / END
PROGRAMMING bar codes
Disable Check Char Transmission
Enable Check Char Transmission
DEFAULT
118
Magellan TM 3300HSi
Codabar
Codabar — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable Length 1 and Length 2 values.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Codabar Length 1, Length 2 Programming Instructions
See
Length 1, Length 2 Programming Instructions on page 154 for
detailed instructions on setting this feature.
For Codabar bar codes, all start, stop, check and data characters are included in the length calculations.
NOTE
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 03
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 50
Product Reference Guide 119
Symbologies
Codabar — continued
Start/Stop Character Type
Codabar has four pairs of Start/Stop patterns. Select one pair to match your application.
START / END
PROGRAMMING bar codes
Start/Stop Type: ABCD/TN*E
Start/Stop Type: ABCD/ABCD
Start/Stop Type: abcd/tn*e
Start/Stop Type: abcd/abcd
DEFAULT
Start/Stop Character Transmission
The transmission of start and end characters of Codabar is selected below.
START / END
PROGRAMMING bar codes
Disable Start/Stop Char Transmission
Enable Start/Stop Char Transmission
DEFAULT
120
Magellan TM 3300HSi
Start/Stop Character Match
This feature enables/disables the requirement that start and stop characters match .
START / END
PROGRAMMING bar codes
Disable Start/Stop Char Match
DEFAULT
Enable Start/Stop Char Match
Code 93
The following options apply to the Code 93 symbology.
Disable/Enable Code 93
When this feature is disabled, the scanner will not read Code 93 bar codes.
START / END
PROGRAMMING bar codes
Disable Code 93
DEFAULT
Enable Code 93
Code 93
Product Reference Guide 121
Symbologies
Code 93 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable Length 1 and Length 2 values.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Code 93 Length 1, Length 2 Programming Instructions
See
Length 1, Length 2 Programming Instructions on page 154 for
detailed instructions on setting this feature.
For Code 93 bar codes, only the data characters are included in the length calculations.
NOTE
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 01
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 50
122
Magellan TM 3300HSi
MSI
The following options apply to the MSI symbology.
Disable/Enable MSI
When this feature is disabled, the scanner will not read MSI bar codes.
START / END
PROGRAMMING bar codes
Disable Code 93
DEFAULT
Enable Code 93
MSI Check Character Transmit
Enable this option to transmit the check character with scanned bar code data.
Applies when
MSI Check Character Calculation is enabled.
START / END
PROGRAMMING bar codes
Disable Check Char Transmission
Enable Check Char Transmission
DEFAULT
MSI
Product Reference Guide 123
Symbologies
MSI — continued
MSI Check Character Calculation
Enables/disables calculation and verification of optional MSI check characters. When disabled, any check characters in an MSI label are treated as data characters.
START / END
PROGRAMMING bar codes
Disable Check Character Calculation
Enable Check Character Calculation
DEFAULT
MSI Number of Check Characters
Specifies number of MSI check characters to be calculated and verified.
START / END
PROGRAMMING bar codes
One Check Character
DEFAULT
Two Check Characters
124
Magellan TM 3300HSi
MSI
MSI — continued
MSI Length Control
Specifies either variable-length decoding or fixed-length decoding for MSI.
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable Length 1 and Length 2 values.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
MSI Length 1, Length 2 Programming Instructions
1. See Length 1, Length 2 Programming Instructions on page 154 for detailed instructions on setting this feature .
For MSI bar codes, length includes the barcode's check and data characters.
NOTE
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 04
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 10
Product Reference Guide 125
Symbologies
NOTES
126
Magellan TM 3300HSi
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 9 Getting Started
- 9 About This Manual
- 9 Manual Conventions
- 10 Connecting the Scanner
- 10 RS-232 Serial Connection
- 11 USB Connection
- 11 IBM Connection
- 11 Keyboard Wedge Connection
- 12 Error Codes
- 12 Installation
- 12 1. Decide the best situation for the scanner by considering...
- 12 2. The countertop must be modified to accept the scanner. At the time of this writing, three options are available.
- 12 3. Remove the Connector Cover, then connect and route the cables at the scanner.
- 12 4. Seat the scanner or in the countertop opening (or adapter).
- 12 5. Switch the terminal OFF.
- 13 6. Connect the interface cable to the terminal.
- 13 7. If required, connect the scanner’s AC Adapter to the AC outlet.
- 13 8. Switch the terminal ON.
- 13 9. Verify operation by scanning a few known-good bar code labels. The scanner should now be communicating the bar code data to the POS terminal.
- 13 10. This concludes the installation instructions.
- 14 LED and Beeper Indicators
- 14 Table 1 . Green LED Indications
- 15 Table 2 . Beeper Functions
- 16 Programming
- 16 Using the Programming Bar Codes
- 16 Resetting the Standard Product Defaults
- 16 Data Matrix Programming Labels
- 17 Bar Code Mask
- 18 Going Green
- 18 LED Class
- 19 General Features
- 19 Double Read Timeout for Linear Labels
- 21 Double Read Timeout for 2D Labels
- 22 Scanner Button Options
- 23 Camera Button Mode
- 24 LED Level
- 25 Auxiliary Port Mode
- 26 Auxiliary Port Baud Rate
- 27 Productivity Index Reporting (PIR)
- 28 Sleep Mode
- 30 Wake Up Intensity
- 32 LED and Beeper Indicators
- 32 Power On Alert
- 32 External Read Indicator (ERI) Active State High
- 33 ERI Timeout
- 34 Good Read: When to Indicate
- 35 Good Read Beep Control
- 35 Good Read Beep Frequency
- 36 Good Read Beep Length
- 37 Good Read Beep Volume
- 38 Cell Phone Mode
- 39 Image Capture
- 39 Image Capture
- 39 How to Capture an Image
- 39 Image Capture to a microSD Card by Scanning a Special Label
- 40 Image Capture to the Host by Host Command
- 41 Image Capture to a microSD Card by Optional Remote Camera Button Press
- 42 Image Compression
- 42 1. Scan the START bar code.
- 42 2. Scan the Set Image Compression bar code.
- 42 3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero-padded) representing the desired compression. The configurable range is 01-0x64 by increments of 01.
- 42 4. Scan the END bar code.
- 42 Image Format
- 43 Image Size
- 44 Image Brightness
- 44 1. Scan the START bar code.
- 44 2. Scan the Set Image Brightness bar code.
- 44 3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero-padded) representing the desired brightness in decimal notation. The configurable range is 01-0x0A by increments of 01.
- 44 4. Scan the END bar code.
- 44 Image Contrast
- 44 1. Scan the START bar code.
- 44 2. Scan the Set Image Contrast bar code.
- 44 3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero-padded) representing the desired contrast in decimal notation. The configurable range is 01-0x0A by increments of 01.
- 44 4. Scan the END bar code.
- 45 Interface Related Features
- 45 Table 4-1 . Interfaces Supported
- 46 Table 4-2 . Keyboard Wedge Interface Reference
- 47 Interface Selection
- 49 Interface Features
- 49 Obey/Ignore Host Commands
- 50 Host Transmission Buffers
- 51 RS-232 Interface Features
- 53 Hardware Flow Control
- 53 Disable Hardware Control
- 53 Enable CTS Flow Control
- 53 Enable CTS Scan Control
- 54 Intercharacter Delay
- 55 Software Flow Control
- 56 Host Echo
- 57 Host Echo Quiet Interval
- 58 Signal Voltage: Normal/TTL
- 59 RS-232 Invert
- 59 Beep on ASCII BEL
- 60 Beep on Not on File
- 61 ACK NAK Options
- 62 ACK Character
- 62 NAK Character
- 63 Retry on ACK NAK Timeout
- 63 ACK NAK Timeout Value
- 64 ACK NAK Retry Count
- 65 ACK NAK Error Handling
- 66 Transmission Failure Indication
- 66 Single Cable RS-232
- 66 Single Cable RS-232 Options
- 67 Single Cable RS-232 RTS CTS Selection
- 68 Single Cable RS-232 Use BCC
- 68 Single Cable RS-232 Use ACK/NAK
- 69 Single Cable RS-232 Use STX
- 69 Set Single Cable RS-232 STX Character
- 69 1. Scan the START/END bar code.
- 69 2. Scan the bar code, SET SINGLE CABLE RS-232 STX CHARACTER below. You’ll need to cover any unused bar codes on this and the facing page to ensure the scanner reads only the bar code you intend to scan.
- 69 3. Scan the appropriate characters/digits from the keypad in Appendix C, Alpha-Numeric Pad that represent the decimal designation for the desired character. A table containing the ASCII Character Set and their corresponding hex values is available in...
- 69 4. The scanner will automatically exit Programming Mode when the appropriate amount of digits have been scanned.
- 70 Single Cable RS-232 Use ETX
- 70 Set Single Cable RS-232 ETX Character
- 70 1. Scan the START/END bar code.
- 70 2. Scan the bar code, SET SINGLE CABLE RS-232 ETX CHARACTER below. You’ll need to cover any unused bar codes on this and the facing page to ensure the scanner reads only the bar code you intend to scan.
- 70 3. Scan the appropriate characters/digits from the keypad in Appendix C, Alpha-Numeric Pad that represent the decimal designation for the desired character. A table containing the ASCII Character Set and their corresponding hex values is available in...
- 70 4. The scanner will automatically exit Programming Mode when the appropriate amount of digits have been scanned.
- 71 Single Cable Pacesetter Plus
- 71 Single Cable Datalogic Extensions
- 72 USB-OEM Interface Features
- 72 USB-OEM Device usage
- 72 IBM
- 72 IBM Transmit Labels in Code 39 Format
- 73 Keyboard Wedge
- 73 USB Keyboard
- 75 Caps Lock State
- 79 USB COM Interface Set-up
- 79 1. Execute the DLS-USB-COM driver file.
- 79 2. When the scanner is first plugged into the PC, Windows will bring up the “Found New Hardware” message.
- 79 3. The installation is complete.
- 81 Data Editing
- 81 Data Editing Overview
- 81 Please Keep In Mind...
- 82 Global Prefix/Suffix
- 83 AIM ID
- 84 Label ID
- 90 Case Conversion
- 91 Character Conversion
- 91 1. Scan the START/END bar code.
- 91 2. Scan the Character Conversion bar code.
- 91 3. Determine the desired string. Up to sixteen positions can be determined as in the above example. Next, turn to the ASCII Character Set on the inside back cover of this manual and find the equivalent hex digits needed to fulfill the string.
- 91 4. Turn to Appendix C, Alpha-Numeric Pad and scan the bar codes representing the hex characters determined in the previous step. When the last character is scanned, the scanner will sound a triple beep.
- 91 5. Scan the START/END bar code to exit Programming Mode.
- 93 Symbologies
- 93 Factory Defaults
- 93 UPC-A
- 93 Disable/Enable UPC-A
- 94 Check Digit Transmission
- 94 Number System Transmission
- 95 Expand UPC-A to EAN-13
- 96 UPC-E
- 96 Disable/Enable UPC-E
- 96 Check Digit Transmission
- 97 Number System Digit
- 97 Expand to UPC-E to UPC-A
- 98 Expand UPC-E to EAN13
- 99 GTIN
- 99 Expand UPC/EAN to GTIN
- 100 EAN-13
- 100 Disable/Enable EAN-13
- 100 Check Digit Transmission
- 101 EAN-13 Flag 1 Character
- 101 ISBN
- 102 EAN-8
- 102 Disable/Enable EAN-8
- 102 Check Digit Transmission
- 103 Expand EAN-8 to EAN-13
- 104 EAN Two-Label
- 104 EAN Two-Label Combined Transmission
- 105 Price Weight Check Digit
- 106 Add-ons
- 106 None
- 106 2 Digits
- 106 5 Digits
- 106 Code 128 Add-on
- 108 GS1 DataBar Omnidirectional / Stacked Omnidirectional
- 108 Disable/Enable GS1 DataBar Omnidirectional
- 108 UCC/EAN 128 Emulation
- 109 GS1 DataBar Expanded / Expanded Stacked
- 109 Disable/Enable GS1 DataBar Expanded
- 109 GS1-128 Emulation
- 110 Length Control
- 110 Fixed Length Decoding
- 110 Variable Length Decoding
- 110 GS1 DataBar Expanded Length 1, Length 2 Programming Instructions
- 111 Coupon Read Control
- 112 GS1 DataBar Limited
- 112 Disable/Enable GS1 DataBar Limited
- 112 GS1-128 Emulation
- 113 Code 39
- 113 Disable/Enable Code 39
- 113 Check Character Calculation
- 114 Check Character Transmit
- 114 Start/Stop Characters
- 115 Code 39 Full ASCII
- 116 Length Control
- 116 Fixed Length Decoding
- 116 Variable Length Decoding
- 116 Code 39 Length 1, Length 2 Programming Instructions
- 117 Code 32 Italian Pharmacode
- 117 Disable/Enable Code 32 Italian Pharmacode
- 117 Start/Stop Characters
- 118 Code 32 Italian Pharmacode — continued
- 118 Check Character Transmit
- 119 Code 128
- 119 Disable/Enable Code 128
- 119 Disable/Enable EAN 128
- 120 Transmit Function Characters
- 121 Length Control
- 121 Fixed Length Decoding
- 121 Variable Length Decoding
- 121 Code 128 Length 1, Length 2 Programming Instructions
- 122 Code 128 Conversion to Code 39
- 122 Interleaved 2 of 5
- 122 Disable/Enable Interleaved 2 of 5
- 123 Check Digit Calculation
- 123 Check Digit Transmit
- 124 Length Control
- 124 Fixed Length Decoding
- 124 Variable Length Decoding
- 124 Interleaved 2 of 5 Length 1, Length 2 Programming Instructions
- 125 Codabar
- 125 Disable/Enable Codabar
- 125 Check Character Verification
- 126 Check Character Transmit
- 127 Length Control
- 127 Fixed Length Decoding
- 127 Variable Length Decoding
- 127 Codabar Length 1, Length 2 Programming Instructions
- 128 Start/Stop Character Type
- 128 Start/Stop Character Transmission
- 129 Start/Stop Character Match
- 129 Code 93
- 129 Disable/Enable Code 93
- 130 Length Control
- 130 Fixed Length Decoding
- 130 Variable Length Decoding
- 130 Code 93 Length 1, Length 2 Programming Instructions
- 131 MSI
- 131 Disable/Enable MSI
- 131 MSI Check Character Transmit
- 132 MSI Check Character Calculation
- 132 MSI Number of Check Characters
- 133 MSI Length Control
- 133 Fixed Length Decoding
- 133 Variable Length Decoding
- 133 MSI Length 1, Length 2 Programming Instructions
- 133 1. See Length 1, Length 2 Programming Instructions on page 154 for detailed instructions on setting this feature.
- 135 2D Symbologies
- 135 2D Symbologies
- 135 Factory Defaults
- 136 PDF 417
- 136 Disable/Enable PDF 417
- 136 Allow Zero Length PDF 417 Reading
- 137 Length Control
- 137 Fixed Length Decoding
- 137 Variable Length Decoding
- 137 1. Scan the START bar code.
- 137 2. Scan the Fixed Length Decoding bar code.
- 137 3. Scan the END bar code.
- 137 4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming Instructions below.
- 137 5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the PDF 417 Length 1, Length 2 Programming Instructions below.
- 137 1. Scan the START bar code.
- 137 2. Scan the Variable Length Decoding bar code.
- 137 3. Scan the END bar code.
- 137 4. Set Length 1 to the minimum length by following the PDF 417 Length 1, Length 2 Programming Instructions below.
- 137 5. Set Length 2 to the maximum length by following the PDF 417 Length 1, Length 2 Programming Instructions below.
- 138 PDF 417 Length 1, Length 2 Programming Instructions
- 138 1. Scan the START bar code.
- 138 2. Scan either the Set Length 1 or Set Length 2 bar code.
- 138 3. Turn to Appendix C, Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
- 139 Micro PDF 417
- 139 Disable/Enable Micro PDF 417
- 140 Length Control
- 140 Fixed Length Decoding
- 140 Variable Length Decoding
- 140 1. Scan the START bar code.
- 140 2. Scan the Fixed Length Decoding bar code.
- 140 3. Scan the END bar code.
- 140 4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming Instructions below.
- 140 5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the Micro PDF 417 Length 1, Length 2 Programming Instructions below.
- 140 1. Scan the START bar code.
- 140 2. Scan the Variable Length Decoding bar code.
- 140 3. Scan the END bar code.
- 140 4. Set Length 1 to the minimum length by following the Micro PDF 417 Length 1, Length 2 Programming Instructions below.
- 140 5. Set Length 2 to the maximum length by following the Micro PDF 417 Length 1, Length 2 Programming Instructions below.
- 141 Micro PDF 417 Length 1, Length 2 Programming Instructions
- 141 1. Scan the START bar code.
- 141 2. Scan either the Set Length 1 or Set Length 2 bar code.
- 141 3. Turn to Appendix C, Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
- 142 Datamatrix
- 142 Disable/Enable Datamatrix
- 143 Length Control
- 143 Fixed Length Decoding
- 143 Variable Length Decoding
- 143 1. Scan the START bar code.
- 143 2. Scan the Fixed Length Decoding bar code.
- 143 3. Scan the END bar code.
- 143 4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming Instructions below.
- 143 5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the Datamatrix Length 1, Length 2 Programming Instructions below.
- 143 1. Scan the START bar code.
- 143 2. Scan the Variable Length Decoding bar code.
- 143 3. Scan the END bar code.
- 143 4. Set Length 1 to the minimum length by following the Datamatrix Length 1, Length 2 Programming Instructions below.
- 143 5. Set Length 2 to the maximum length by following the Datamatrix Length 1, Length 2 Programming Instructions below.
- 144 Datamatrix Length 1, Length 2 Programming Instructions
- 144 1. Scan the START bar code.
- 144 2. Scan either the Set Length 1 or Set Length 2 bar code.
- 144 3. Turn to Appendix C, Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
- 145 QR Code
- 145 Disable/Enable QR Code
- 146 Length Control
- 146 Fixed Length Decoding
- 146 Variable Length Decoding
- 146 1. Scan the START bar code.
- 146 2. Scan the Fixed Length Decoding bar code.
- 146 3. Scan the END bar code.
- 146 4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming Instructions below.
- 146 5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the QR Code Length 1, Length 2 Programming Instructions below.
- 146 1. Scan the START bar code.
- 146 2. Scan the Variable Length Decoding bar code.
- 146 3. Scan the END bar code.
- 146 4. Set Length 1 to the minimum length by following the QR Code Length 1, Length 2 Programming Instructions below.
- 146 5. Set Length 2 to the maximum length by following the QR Code Length 1, Length 2 Programming Instructions below.
- 147 QR Code Length 1, Length 2 Programming Instructions
- 147 1. Scan the START bar code.
- 147 2. Scan either the Set Length 1 or Set Length 2 bar code.
- 147 3. Turn to Appendix C, Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
- 148 Maxicode
- 148 Disable/Enable Maxicode
- 149 Length Control
- 149 Fixed Length Decoding
- 149 Variable Length Decoding
- 149 1. Scan the START bar code.
- 149 2. Scan the Fixed Length Decoding bar code.
- 149 3. Scan the END bar code.
- 149 4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming Instructions below.
- 149 5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the Maxicode Length 1, Length 2 Programming Instructions below.
- 149 1. Scan the START bar code.
- 149 2. Scan the Variable Length Decoding bar code.
- 149 3. Scan the END bar code.
- 149 4. Set Length 1 to the minimum length by following the Maxicode Length 1, Length 2 Programming Instructions below.
- 149 5. Set Length 2 to the maximum length by following the Maxicode Length 1, Length 2 Programming Instructions below.
- 150 Maxicode Length 1, Length 2 Programming Instructions
- 150 1. Scan the START bar code.
- 150 2. Scan either the Set Length 1 or Set Length 2 bar code.
- 150 3. Turn to Appendix C, Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
- 151 Aztec
- 151 Disable/Enable Aztec
- 152 Length Control
- 152 Fixed Length Decoding
- 152 Variable Length Decoding
- 152 1. Scan the START bar code.
- 152 2. Scan the Fixed Length Decoding bar code.
- 152 3. Scan the END bar code.
- 152 4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming Instructions below.
- 152 5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the Aztec Length 1, Length 2 Programming Instructions below.
- 152 1. Scan the START bar code.
- 152 2. Scan the Variable Length Decoding bar code.
- 152 3. Scan the END bar code.
- 152 4. Set Length 1 to the minimum length by following the Aztec Length 1, Length 2 Programming Instructions below.
- 152 5. Set Length 2 to the maximum length by following the Aztec Length 1, Length 2 Programming Instructions below.
- 153 Aztec Length 1, Length 2 Programming Instructions
- 153 1. Scan the START bar code.
- 153 2. Scan either the Set Length 1 or Set Length 2 bar code.
- 153 3. Turn to Appendix C, Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
- 154 Composite Labels
- 154 Disable/Enable GS1 DataBar Omnidirectional 2D Component
- 154 Disable/Enable GS1 DataBar Expanded 2D Component
- 155 Disable/Enable GS1 DataBar Limited 2D Component
- 157 Advanced Decoding Features
- 157 Inverse Label Reading
- 158 UPC/EAN Quiet Zone
- 159 References
- 160 Global Prefix/Suffix
- 160 1. Determine which ASCII character(s) are to be added to scanned bar code data. In this example, we’ll add a dollar sign (‘$’) as a prefix.
- 160 2. Scan the START bar code.
- 160 3. Scan the SET PREFIX bar code.
- 160 4. Reference the ASCII Character Set on the inside back cover of this manual, to find the hex value assigned to the desired character. The corresponding hex number for the ‘$’ character is 24. To enter this selection code, scan the ‘2’ and ...
- 160 5. Scan the END bar code once to finish the string, then scan END again to exit Programming Mode.
- 160 6. The resulting message string would appear as follows:
- 161 Label ID
- 161 1. Scan the START bar code.
- 161 2. Select Label ID position as either BEFORE or AFTER by scanning the appropriate bar code.
- 161 3. Scan a bar code to select the symbology for which you wish to configure a custom Label ID.
- 161 4. Determine the desired character(s) (you may choose up to three) which will represent the Label ID for the selected symbology. Next, turn to the ASCII Character Set on the inside back cover of this manual and find the equivalent hex digits associat...
- 161 5. Turn to Appendix C, Alpha-Numeric Pad and scan the bar codes representing the hex characters determined in the previous step. For example, to make an equal sign (=), scan ‘3’ and ‘D’ followed by ‘0’ six times. Since this is a three-cha...
- 161 6. Scan the END bar code to exit programming mode.
- 162 Length Control
- 162 Fixed Length Decoding
- 162 Variable Length Decoding
- 162 1. Scan the START/END bar code.
- 162 2. Scan the Fixed Length Decoding bar code for the desired symbology.
- 162 3. Scan the START/END bar code.
- 162 4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming Instructions below.
- 162 5. Set Length 2 to the second fixed length (or to ‘00’ if there is only one fixed length) by following the Length 1, Length 2 Programming Instructions below.
- 162 1. Scan the START/END bar code.
- 162 2. Scan the Variable Length Decoding bar code for the desired symbology.
- 162 3. Scan the START/END bar code.
- 162 4. Set Length 1 to the first variable length by following the Length 1, Length 2 Programming Instructions below.
- 162 5. Set Length 2 to the second variable length by following the Length 1, Length 2 Programming Instructions below.
- 162 Length 1, Length 2 Programming Instructions
- 162 1. Scan the START/END bar code.
- 162 2. Scan either the Set Length 1 or Set Length 2 bar code for the desired symbology.
- 162 3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero padded) representing the length in decimal notation. The number of characters that can be set varies, depending upon the symbology. Reference the page for your selected symbology ...
- 162 4. Scan the START/END bar code
- 163 Product Specifications
- 163 Optical and Read Performance Parameters
- 163 Scanner Dimensions
- 164 Physical Properties
- 164 Electrical Parameters
- 164 Environmental Parameters
- 164 Other Parameters
- 165 Cable Pinouts
- 165 Standard Cable Pinouts (Primary Interface Cables)
- 167 Alpha-Numeric Pad
- 169 Factory Default Settings
- 169 Factory Defaults by Interface
- 175 Keyboard Function Key Mappings
- 175 Keyboard Model Cross Reference
- 175 Table 1 . Keyboard Model Cross Reference
- 176 Table 2 . USB Function Key Usage Map
- 177 Table 3 . Scanset 1 Function Key Map
- 177 Table 4 . Scanset 2 Function Key Map
- 178 Table 5 . Scanset 3, 102-Key Function Key Map
- 179 Table 6 . Scanset 3 122-Key Function Key Map
- 180 Table 7 . Japanese DOS Function Key Map
- 181 Table 8 . NEC 9801-Key Function Key Map
- 183 Host Commands
- 183 Accepting RS-232 Commands
- 185 Sample Symbols
- 185 1D Symbol Samples
- 187 2D Sample Symbols
- 188 Composite Sample Symbols
- 189 microSD Card
- 189 microSDHC Compatibility
- 189 microSD Card Insertion
- 189 1. Read all of these instructions before starting.
- 189 2. If you have not already done so, remove the scanner from its installed position to allow access to the microSD card slot.
- 189 3. Use a coin or similar blunt object to lever the top cover from the scanner, then grasp the lift handles and carefully lift the unit from the counter.
- 189 4. Ensure there are no other cables attached to the scanner, then apply power and wait for the reset beep.
- 189 5. Lift and rotate the rubber cover to access the card slot, then carefully insert the microSD card into the slot until it "clicks" into place.
- 189 6. If installed properly, you should immediately hear an audible signal upon insertion or removal of a microSD card. Various operations will also be indicated by the scanner’s good read LED.
- 190 microSD Card Removal
- 190 1. Push in gently using your finger or thumbnail to disengage and remove the microSD card. Remember to keep your finger in place atop the card’s edge to avoid accidentally “launching” the card from the springloaded slot.
- 190 2. Reconnect all cables which were disconnected earlier.
- 190 Autorun File Processing
- 190 microSD Function Summary
- 191 microSD Function Details
- 191 From Scanner to microSD Card
- 191 Capture and save an image to a microSD card by scanning a label.
- 191 1. Insert the microSD card into the scanner
- 191 2. Scan the Capture Label
- 191 3. Place the item to be captured in front of the scanner.
- 191 4. Upon scanner audio indication of completion, an image is saved to the microSD card.
- 191 Export a Configuration file from the Scanner to the microSD card
- 191 1. Generate a text file by any text editor as follows and save it as AUTORUN.DLS.
- 191 2. Save or copy file AUTORUN.DLS to microSD card
- 191 3. Insert the microSD card to scanner
- 191 4. Wait for 3 seconds,
- 191 Export Scanner Status to microSD card
- 192 1. Insert the microSD card into the scanner
- 192 2. Scan the status export label
- 192 3. Upon scanner audio indication of completion, the scanner status text file named status.txt is saved to the microSD card.
- 192 1. Generate a text file by any text editor as follows and save it as AUTORUN.DLS
- 192 2. Save or copy the AUTORUN.DLS file to the microSD card
- 192 3. Insert the microSD card into the scanner
- 192 4. Wait for about 3 seconds.
- 192 From microSD Card to Scanner
- 192 Application code load to scanner
- 192 1. Generate a text file by any text editor as follows and save it as AUTORUN.DLS
- 192 2. Step 2: Save or copy file autorun.dls to microSD card and copy the application code (example R96- APP1.BIN) to the microSD card.
- 192 3. Insert the microSD card into the scanner.
- 192 4. Upon scanner audio indication of completion, the application code R96-APP1.BIN is loaded to the scanner. Typically, this takes about 45 seconds.
- 193 Configuration load to scanner
- 193 1. Generate a text file by any text editor as follows and save it as AUTORUN.DLS
- 193 2. Save or copy the autorun.dls file, and copy the CPLD code (example R96-CFG1.TEX) to the microSD card
- 193 3. Insert the microSD card into to the scanner
- 193 4. Upon scanner audio indication of completion, configuration R96-CFG1.TEX is loaded to the scanner.
- 195 Handheld Data Format Requirements
- 195 Handheld Data Format Requirements General
- 196 Datalogic Handheld Data Format Requirements
- 196 RSS-14
- 196 RSS Expanded
- 196 UPC-A
- 196 UPC-A with 2-Digit Supplemental
- 196 UPC-A with 5-Digit Supplemental
- 196 UPC-A with Code 128 Supplemental
- 197 UPC-E
- 198 UPC-E with 2-Digit Supplemental
- 198 UPC-E with 5-Digit Supplemental
- 198 UPC-E with Code 128 Supplemental
- 199 EAN-8
- 199 EAN-8 with 2-Digit Supplemental
- 199 EAN-8 with 5-Digit Supplemental
- 199 EAN-8 with Code 128 Supplemental
- 199 EAN-13
- 199 EAN-13 with 2-Digit Supplemental
- 199 EAN-13 with 5-Digit Supplemental
- 200 EAN-13 with Code 128 Supplemental
- 200 Code 39
- 200 Code 39-Pharmacode
- 200 I 2 of 5
- 201 Codabar
- 201 Code 128
- 202 MSI
- 202 Code 93
- 202 PDF417
- 203 AIM Formats
- 203 UPC-A
- 203 UPC-E
- 203 EAN-13
- 203 EAN-8
- 203 2-Digit Supplemental
- 204 5-Digit Supplemental
- 204 Code 128 Supplemental
- 204 Bookland
- 204 Code 39
- 205 Codabar
- 205 MSI
- 205 Code 93
- 205 RSS-14
- 205 RSS Expanded
- 206 I 2 of 5
- 206 Code 128 / EAN128
- 206 PDF417
- 206 “Unknown” AIM ID (an AIM ID which is not specified above)