advertisement
2D Symbologies
The features in this section are available ONLY for models with 2D features activated.
NOTE
2D Symbologies
The scanner supports the 2D symbologies (bar code types) listed below. Available options for each 2D symbology are included in this chapter.
Factory Defaults— for the standard RS-232 interface are indicated in bold text throughout.
Product Reference Guide
127
2D Symbologies
PDF 417
Disable/Enable PDF 417
When disabled, the scanner will not read PDF 417 bar codes.
START / END
PROGRAMMING bar codes
Disable PDF 417
Enable PDF 417
DEFAULT
Allow Zero Length PDF 417 Reading
This enables/disables the scanner’s ability to read PDF417 bar codes containing a zero length codeword.
START / END
PROGRAMMING bar codes
Disable Zero Length PDF 417 Reading
DEFAULT
Enable Zero Length PDF 417 Reading
128
Magellan TM 3300HSi
2D Symbologies
PDF 417 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START bar code.
2. Scan the Fixed Length Decoding bar code.
3. Scan the END bar code.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the
PDF 417 Length 1, Length 2 Programming Instructions
below.
Configuring Variable Length Decoding:
1. Scan the START bar code.
2. Scan the Variable Length Decoding bar code.
3. Scan the END bar code.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Product Reference Guide 129
2D Symbologies
PDF 417 — continued
PDF 417 Length 1, Length 2 Programming Instructions
1. Scan the START bar code.
2. Scan either the Set Length 1 or Set Length 2 bar code.
3. Turn to Appendix C, Alpha-Numeric Pad
and scan the four digits (zero-padded) representing the length.
For PDF 417 bar codes, only the data characters are included in the length calculations.
Any value set higher than 2710 will be considered to be 2710.
NOTE
Scan the END bar code.
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 2710
130
Magellan TM 3300HSi
Micro PDF 417
Disable/Enable Micro PDF 417
When disabled, the scanner will not read Micro PDF 417 bar codes.
START / END
PROGRAMMING bar codes
Disable Micro PDF 417
DEFAULT
2D Symbologies
Enable Micro PDF 417
Product Reference Guide 131
2D Symbologies
Micro PDF 417 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START bar code.
2. Scan the Fixed Length Decoding bar code.
3. Scan the END bar code.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the
Micro PDF 417 Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START bar code.
2. Scan the Variable Length Decoding bar code.
3. Scan the END bar code.
4. Set Length 1 to the minimum length by following the Micro PDF 417 Length 1, Length 2
Programming Instructions below.
5. Set Length 2 to the maximum length by following the Micro PDF 417 Length 1, Length 2
Programming Instructions below.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
132
Magellan TM 3300HSi
2D Symbologies
Micro PDF 417 — continued
Micro PDF 417 Length 1, Length 2 Programming Instructions
1. Scan the START bar code.
2. Scan either the Set Length 1 or Set Length 2 bar code.
3. Turn to Appendix C, Alpha-Numeric Pad
and scan the four digits (zero-padded) representing the length.
For Micro PDF 417 bar codes, only the data characters are included in the length calculations.
Any value set higher than 366 will be considered to be 366.
NOTE
Scan the END bar code.
START / END
PROGRAMMING bar codes
Set Length 1
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 0366
Product Reference Guide 133
2D Symbologies
Datamatrix
Disable/Enable Datamatrix
When disabled, the scanner will not read Datamatrix bar codes.
START / END
PROGRAMMING bar codes
Disable Datamatrix
Enable Datamatrix
DEFAULT
134
Magellan TM 3300HSi
2D Symbologies
Datamatrix — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START bar code.
2. Scan the Fixed Length Decoding bar code.
3. Scan the END bar code.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the
Datamatrix Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START bar code.
2. Scan the Variable Length Decoding bar code.
3. Scan the END bar code.
START / END
Fixed Length Decoding
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Product Reference Guide 135
2D Symbologies
Datamatrix — continued
Datamatrix Length 1, Length 2 Programming Instructions
1. Scan the START bar code.
2. Scan either the Set Length 1 or Set Length 2 bar code.
3. Turn to Appendix C, Alpha-Numeric Pad
and scan the four digits (zero-padded) representing the length.
For Datamatrix bar codes, only the data characters are included in the length calculations.
Any value set higher than 800 will be considered to be 800.
NOTE
Scan the END bar code.
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 0800
136
Magellan TM 3300HSi
QR Code
Disable/Enable QR Code
When disabled, the scanner will not read QR Code labels.
START / END
PROGRAMMING bar codes
Disable QR Code
DEFAULT
Enable QR Code
2D Symbologies
Product Reference Guide 137
2D Symbologies
QR Code — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START bar code.
2. Scan the Fixed Length Decoding bar code.
3. Scan the END bar code.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the
QR Code Length 1, Length 2 Programming Instructions
below.
Configuring Variable Length Decoding:
1. Scan the START bar code.
2. Scan the Variable Length Decoding bar code.
3. Scan the END bar code.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
138
Magellan TM 3300HSi
2D Symbologies
QR Code — continued
QR Code Length 1, Length 2 Programming Instructions
1. Scan the START bar code.
2. Scan either the Set Length 1 or Set Length 2 bar code.
3. Turn to Appendix C, Alpha-Numeric Pad
and scan the four digits (zero-padded) representing the length.
For 2d Code labels, only the data characters are included in the length calculations.
Any value set higher than 2710 will be considered to be 2710.
NOTE
Scan the END bar code.
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 2710
Product Reference Guide 139
2D Symbologies
Maxicode
Disable/Enable Maxicode
When disabled, the scanner will not read Maxicode labels.
START / END
PROGRAMMING bar codes
Disable Maxicode
DEFAULT
Enable Maxicode
140
Magellan TM 3300HSi
2D Symbologies
Maxicode — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START bar code.
2. Scan the Fixed Length Decoding bar code.
3. Scan the END bar code.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the
Maxicode Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START bar code.
2. Scan the Variable Length Decoding bar code.
3. Scan the END bar code.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Product Reference Guide 141
2D Symbologies
Maxicode — continued
Maxicode Length 1, Length 2 Programming Instructions
1. Scan the START bar code.
2. Scan either the Set Length 1 or Set Length 2 bar code.
3. Turn to Appendix C, Alpha-Numeric Pad
and scan the four digits (zero-padded) representing the length.
For Maxicode labels, only the data characters are included in the length calculations.
Any value set higher than 138 will be considered to be 138.
NOTE
Scan the END bar code.
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 0138
142
Magellan TM 3300HSi
Aztec
Disable/Enable Aztec
When disabled, the scanner will not read Aztec labels.
START / END
PROGRAMMING bar codes
Disable Aztec
DEFAULT
Enable Aztec
2D Symbologies
Product Reference Guide 143
2D Symbologies
Aztec — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a bar code if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a bar code if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START bar code.
2. Scan the Fixed Length Decoding bar code.
3. Scan the END bar code.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by following the
Aztec Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START bar code.
2. Scan the Variable Length Decoding bar code.
3. Scan the END bar code.
below.
below.
START / END
PROGRAMMING bar codes
Variable Length Decoding
DEFAULT
Fixed Length Decoding
144
Magellan TM 3300HSi
2D Symbologies
Aztec — continued
Aztec Length 1, Length 2 Programming Instructions
1. Scan the START bar code.
2. Scan either the Set Length 1 or Set Length 2 bar code.
3. Turn to Appendix C, Alpha-Numeric Pad
and scan the four digits (zero-padded) representing the length.
For Aztec labels, only the data characters are included in the length calculations.
Any value set higher than 3700 will be considered to be 2710.
NOTE
Scan the END bar code.
START / END
PROGRAMMING bar codes
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 2710
Product Reference Guide 145
2D Symbologies
Composite Labels
Disable/Enable GS1 DataBar Omnidirectional 2D Component
When enabled, if a GS1 DataBar Omnidirectional label is decoded which has the 2D linkage flag set, the 2D component must also be decoded or the base label will be discarded.
When disabled, only the GS1 DataBar Omnidirectional base label will be decoded and transmitted regardless of the state of the linkage flag.
START / END
PROGRAMMING bar codes
Disable GS1 DataBar Omnidirectional 2D Component
DEFAULT
Enable GS1 DataBar Omnidirectional 2D Component
Disable/Enable GS1 DataBar Expanded 2D Component
When enabled, if a GS1 DataBar Expanded label is decoded which has the 2D linkage flag set, the 2D component must also be decoded or the base label will be discarded.
When disabled, only the GS1 DataBar Expanded base label will be decoded and transmitted regardless of the state of the linkage flag.
START / END
PROGRAMMING bar codes
Disable GS1 DataBar Expanded 2D Component
DEFAULT
Enable GS1 DataBar Expanded 2D Component
146
Magellan TM 3300HSi
2D Symbologies
Disable/Enable GS1 DataBar Limited 2D Component
When enabled, if a GS1 DataBar Limited label is decoded which has the 2D linkage flag set, the
2D component must also be decoded or the base label will be discarded.
When disabled, only the GS1 DataBar Limited base label will be decoded and transmitted regardless of the state of the linkage flag.
START / END
PROGRAMMING bar codes
Disable GS1 DataBar Limited 2D Component
DEFAULT
Enable GS1 DataBar Limited 2D Component
Product Reference Guide 147
2D Symbologies
NOTES
148
Magellan TM 3300HSi
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement